Laser Pegs G870B INDY CAR Model Instructions

G870B

Please read manual before you begin!

Failure to follow this manual's instructions may
result in damage to the Triangle Power Base,
INDY CAR
AC adapter and/or Laser Pegs®. Not adhering to
these instructions will void the manufacturer's
AGES 5+
warranty. The packaging must be kept because
it contains important information.
12 Models+
Any creation you can build
LIGHTED
WARNING:
CONSTRUCTION SET INCLUDES:
CHOKING HAZARD
-
Small parts.
• 20 Laser Pegs®
Not for children under 3 yrs.
Do not submerge in water.
• 84 Construction Parts
• Triangle Power Base
• Instruction Manual
Requires 3 AA Batteries
EN71, RoHS COMPLIANT
Batteries NOT
Included
This product complies to
all safety requirements
of ASTM F 963
Model Instructions
All additional model instructions can
be downloaded at www.LaserPegs.com
Laser Peg® Parts List
There is No LED In The 90 Degree Peg
x3 x6 x1 x4
x2
Y PEG SQUARE 45° PEG 90° PEG WHEEL PEG Stackable
PEG
Each Laser Peg® is color coded on the circuit board inside
Color
Code each shape. There is No LED In The 90 Degree Peg.
Sound Activated Laser Pegs
®
Triangle Power Base Peg Cord
Construction Parts List
x1
x2
x12
x2
x6
x2
x6
x10
x2
x3
x5
x3 x2
x5
x2
x4
x1
www.LaserPegs.com
This manual is copyright and cannot be reproduced or used online without Laser
Pegs®Ventures LLC permission. Copyright 2014 © All Rights Reserved US Patent
#7,731,558 Additional Global & Multiple Patents Pending. Laser Pegs®Ventures
LLC. 8304 Consumer Ct Sarasota FL. 34240. Contact: Support@LaserPegs.com

Connecting Pegs

To construct with Laser Pegs®, slide two pieces together to form a
connection. Slide each piece on and off smoothly. The 90° Pegs are
essential to construction but they DO NOT LIGHT UP.

Environmental Phenomena

* The unit may malfunction if subjected to radio-frequency interference. It SHOULD revert to
normal operation when the interference stops. If not, it may become necessary to turn the power
off and back on, or remove and reinstall the batteries.
* In the unlikely event of an electrostatic discharge, the unit may malfunction and lose memory,
requiring the user to reset the devise by removing and reinstalling the batteries.
Push Red
Red
Power Button
Power Button
to turn on/off
Push Red Power Button to
cycle through 4 different
light settings.
AC Adapter
SOUND/ON/FLASH/FLASH FASTER Connection
WARNING: STROBE LIGHTS
The toy is not to be connected to more than
MAY CAUSE SEIZURES the recommended number of power supplies

Replacing Batteries

1. Remove the three (3) screws.
Remove the 3 Phillips head screws
2. Place three (3) AA batteries in the correct
position - as displayed inside the Triangle
Power Base.
3. Reassemble the Triangle Power Base.
4. Replace the three (3) screws.
5. Push RED Power Button to turn on!
6. Do not mix old and new batteries.
7. Do not mix alkaline, standard (carbon-
x4 zinc), or rechargeable (nickel-cadmium,
NiMH) batteries!
8. Exhausted batteries are to be removed
from the Triangle Power Base.
9. Never connect more than 200 Laser Pegs®
10. Non-rechargeable batteries are not to be
recharged.
11. Rechargeable batteries are only to be
recharged under adult supervision.
12. Rechargeable batteries are to be removed
from the toy before being recharged.
13. Batteries are to be inserted with the
correct polarity.
14. The supply terminals are not to be short-
circuited. Remove the three Phillips head
15. DO NOT THROW BATTERIES INTO FIRE!
screws with a 4mm screw driver.
Please dispose of batteries properly as per state and local regulations.
Using an
AC Adapt
er
Remove all batteries
from Laser Pegs® power
base before using the
5-volt AC adapter.
*To avoid short-circuits, keep metal objects and
x4
other unauthorized materials from obstructing
the peg holes.
The AC adapter and the Triangle Power Base are to be regularly examined for
x4
damage to the cord, plug, enclosure and other parts, and in the event of such
x6 damage, they must not be used until the damage has been repaired.
x2
WARNING! Each Laser Peg® draws current from the batteries. Therefore, the more
pegs you use, the quicker you will deplete your battery power! As the power
weakens, the current will slowly fail and some Laser Pegs® will illuminate (typically
the reds and yellows) and some won't. When the Laser Pegs® dim the Laser Pegs®
are not broken, they just need stronger batteries or an AC Adapter.
You have 3 simple options...
1. Use a 5-volt AC Adapter –available from www.LaserPegs.com
2. Change the batteries.
3. Use high quality batteries. They will last a little longer, but they will still deplete
rapidly the more laser pegs you connect!
DO NOT SUBMERGE IN WATER
INDY CAR — A high performance automobile built for racing at incredible speeds.
INDY CAR
Model
Difficulty
Level
Peg Holes
A
STEP
1
STEP
2
STEP
3-AA Batteries
3
STEP
4
Requires (3AA) Batteries
STEP
When using an AC
5
Adapter, NEVER
place the adapter
plug into the Tri-
angle Power Base
top peg holes.
STEP
Never connect more than 200
6
Laser Pegs® when using a 5-volt
(2000mA) AC Adapter.
STEP
7
B
STEP
12
STEP
8
STEP
13
C
STEP
14
STEP
9
STEP
15
D
STEP
16
STEP
10
STEP
11