Table of Contents
Advertisement
Quick Links
Advertisement
Table of Contents
Subscribe to Our Youtube Channel
Related Manuals for ASUSTOR AS6 Series
Summary of Contents for ASUSTOR AS6 Series
- Page 1 Memory Installation Guide For ASUSTOR AS6 and AS7 Series NAS Ver.1.0.2.0225...
-
Page 2: Table Of Contents
For AS7 Rackmount Series ................10 2.3.1. Removing the Cover ................... 10 2.3.2. Installing Memory ..................11 2.3.3. Replacing the Cover ................... 12 Appendix ......................14 3.1. Troubleshooting ..................... 14 3.2. Contact ASUSTOR Technical Support ..............14 Page 2 of 14... -
Page 3: Introduction
ASUSTOR NAS Memory Installation Guide 1.1. Notes and Precautions All AS6 Series NAS devices support up to 3GB of memory. Before adding or removing memory modules, please read the following precautions thoroughly. Your NAS and memory modules use high precision components and electronic connector •... -
Page 4: Parts And Tools Needed
ASUSTOR NAS Memory Installation Guide 1.2. Parts and Tools Needed • Phillips head screwdriver Page 4 of 14... -
Page 5: Installation Guide
ASUSTOR NAS Memory Installation Guide 2.1. For AS 6 & AS7 Tower Series Shutdown the NAS by selecting [Shut down] from the ADM User Menu. • Disconnect all cables and devices connected to the NAS including the power cord. •... -
Page 6: Installing Memory
ASUSTOR NAS Memory Installation Guide • Grip the cover from both sides with two hands and then gently push it back to remove it from the chassis. When inserting the memory module into the empty slot, please make sure to align •... -
Page 7: Replacing The Cover
ASUSTOR NAS Memory Installation Guide Using two fingers, carefully push down and then back on the memory module until it • clicks into place. You should be able to hear an audible “click”. • Replace the cover and tighten the three screws that were removed previously. -
Page 8: Installing Memory
ASUSTOR NAS Memory Installation Guide Shutdown the NAS by selecting [Shut down] from the ADM User Menu. • Disconnect all cables and devices connected to the NAS including the power cord. • Use a screwdriver to loosen the three screws found on the rear of the NAS as shown •... -
Page 9: Replacing The Cover
ASUSTOR NAS Memory Installation Guide • Using two fingers, carefully push down and then back on the memory module until it clicks into place. You should be able to hear an audible “click”. Replace the cover and tighten the three screws that were removed previously. -
Page 10: For As7 Rackmount Series
ASUSTOR NAS Memory Installation Guide • Reconnect all cables including the power cord and then start up the NAS. 2.3. For AS7 Rackmount Series Shutdown the NAS by selecting [Shut down] from the ADM User Menu. • Disconnect all cables and devices connected to the NAS including the power cord. -
Page 11: Installing Memory
ASUSTOR NAS Memory Installation Guide Use a screwdriver to loosen the three screws found on the rear of the NAS as shown • in the illustration. Grip the cover from both sides with two hands and then gently push it back to •... -
Page 12: Replacing The Cover
ASUSTOR NAS Memory Installation Guide • Using two fingers, carefully push down on the memory module until the ejector clips lock it into place. Replace the cover and tighten the three screws that were removed previously. • Page 12 of 14... - Page 13 ASUSTOR NAS Memory Installation Guide • Reconnect all cables including the power cord and then start up the NAS. Page 13 of 14...
-
Page 14: Appendix
ASUSTOR NAS Memory Installation Guide 3.1. Troubleshooting Q: After installing new memory my NAS won’t start. What’s wrong? A: Please follow the steps below to resolve this issue: 1. Check if the LED indicators, system buzzer, and LCD display panel are operating normally.
Need help?
Do you have a question about the AS6 Series and is the answer not in the manual?
Questions and answers