LC-37HV4E SERVICE MANUAL S33Y3LC37HV4E LCD COLOUR TELEVISION LC-37HV4E MODEL In the interests of user-safety (Required by safety regulations in some countries) the set should be restored to its original condition and only parts identical to those specified should be used.
LC-37HV4E IMPORTANT SERVICE SAFETY PRECAUTION Ë Service work should be performed only by qualified service technicians who are thor- oughly familiar with all safety checks and the servicing guidelines which follow: » Use an AC voltmeter having with 5000 ohm per volt,...
Page 3
LC-37HV4E Precautions for using lead-free solder 1 Employing lead-free solder "PWBs" of this model employs lead-free solder. The LF symbol indicates lead-free solder, and is attached on the PWBs and service manuals. The alphabetical character following LF shows the type of lead-free solder.
LC-37HV4E REMOVING OF MAJOR PARTS 1.Take off the center and lower terminal covers. 2.Remove the two speaker fixing screws each and the speaker connecting terminal, and take off the speaker. 3.Remove the four stand fixing screws and take off the stand.
Page 13
LC-37HV4E 9.Open six FFC cable holders and remove the three FFC holder (right & left) fixing screws each and all the connec- tors of flat cables (FFC), and take off the FFC holders (right & left). 10.Remove the Speaker-L and-R PWB fixing screws each and the connectors of them, and take off the Speaker-L and-R PWBs.
Page 14
LC-37HV4E 13.Remove the five main PWB fixing screws, and take off the main PWB. 14.Remove the six power PWB fixing screws, and take off the power PWB. 15.Remove the four audio PWB fixing screws, and take off the audio PWB.
Page 15
LC-37HV4E • Handling Precautions for LCD Panel 1. Work in a clean room. (Humidity above 50%) 2. Operators should wear an earthing band. 3. Do not give a shock such as falling and vibration. 4. Use the ionizer. (Within 30 cm) 21.Remove the six LCD panel fixing screws and take off the LCD panel unit.
LC-37HV4E ADJUSTMENT PROCEDURES Though the best adjustment is made at shipment from the factory, the following adjustment is required if the value should be deviated or some adjustment is needed after replacement of parts. Display Side: 1. Preparation for Adjustment The unit needs to be replaced when the AVC System CONFIGROM/IC2202, receiver IC2206 and HDCP key ROM/IC2208 are replaced.
Page 17
LC-37HV4E 5. Adjustment 5-1 VLSBIAS/15V voltage adjustment Shift to Item of VLS BIAS cursor up/down key, and select the value by cursor right/left key. Connect the digital voltage meter to MAIN PWB TP4101/No.30 pin of panel gate socket CN4102, and adjust to be 15.00±0.05V by the cursor up/down key.
Page 18
LC-37HV4E ~ In this state, enter the command, listed below, and "ENTER" on the keyboard for adjustment. Press "ENTER" and make sure that "OK" appears on the terminal software. If "ERR" appears, try again. RS232C commands list Command Function Remarks MSET1001 Background adjustment started.
Page 19
LC-37HV4E Lamp error detection [1] Function This LCD color TV set is equipped with automatic power-off (lamp error detection) function. This safety measure serves if the lamp or the lamp circuit gets in trouble. If by any chance the lamp or the lamp circuit gets in trouble, or if the lamp error detector gets activated for any other reasons, the following happens.
LC-37HV4E TROUBLE SHOOTING TABLE No image or sound comes out. Is the power LED lit up Is the power LED Is the AC cord Replace the AC normal? in green? flashing in red? Is it flashing once in Proceed to "The backlight does one cycle? not light up".
Page 23
LC-37HV4E TROUBLE SHOOTING TABLE (Continued) No image comes out. Is a HIGH appearing Check the circuits at the RESET terminal around X2201 of pin (3) of IC2206? connected to pin (161) of IC2206. Is a clock (91.3 MHz) Is X2201 connected to pin...
Page 24
LC-37HV4E TROUBLE SHOOTING TABLE (Continued) Noise appears on the moving image when the QS drive is turned ON. Is OSTEMP.AD on the 3rd page Check IC4701, IC4901 and of the process adjustment the circuits around them. mode set to 255?
Page 25
LC-37HV4E TROUBLE SHOOTING TABLE (Continued) No sound comes out. (Connect to the AVC System and check.) Check around the Is power supplied to each power regulator circuit IC in the audio unit? (IC3809, IC3810). Is an audio signal appearing Is an audio signal...
LC-37HV4E DESCRIPTION OF SCHEMATIC DIAGRAM VOLTAGE MEASUREMENT CONDITION: 1. When the exclusive-use AC adapter is used, the colour bar signal of colour bar generator for service is input to get the normal screen. When the audio is minimized, the voltage value is measured with the 20 kΩ/V tester.
LC-37HV4E Ref. No. Part No. Description Code Ref. No. Part No. Description Code PARTS LIST DKEYHB453FE50 PARTS REPLACEMENT MAIN Unit (Display) Replacement parts which have these special safety characteristics identified in this manual: electrical components having such features INTEGRATED CIRCUITS are identified by "å"...
Need help?
Do you have a question about the LC-37HV4E and is the answer not in the manual?
Questions and answers