Table of Contents
Advertisement
Quick Links
Advertisement
Table of Contents
Related Manuals for GPI GPR-R220L
Summary of Contents for GPI GPR-R220L
- Page 1 INSTRUCTIONS FOR USE Rotary Laser GPR-R220L...
-
Page 2: Table Of Contents
Content 1) What is included with your GPR-R220L ............... - 2 - 2) Find your way around the GPR-R220L ..............- 3 - 3) Getting set up ......................- 5 - 4) Horizontal Leveling ....................- 6 - 5) Sloping Leveling ...................... - 7 - 6) Vertical Lines ...................... -
Page 3: What Is Included With Your Gpr-R220L
1) What is included with your GPR-R220L Your GPR-R220L includes the following parts: A) Main Instrument B) Laser line detector and Bracket C) Remote Control for Instrument D) Charger E) Target F) Glasses G) Hard Case with Foam Insert H) A replaceable battery Pack Please contact your supplier if any of the above parts are missing. -
Page 4: Find Your Way Around The Gpr-R220L
2) Find your way around the GPR-R220L Plumb up glass Laser module Optical glass Handle Keypad panel Charge socket - 3 -... - Page 5 Slope setting Plus/Right spin X/Y axis switch Minus/Left spin Speed up Scanning On/Off Tilt/H.I alert automatic/Manual - 4 -...
-
Page 6: Getting Set Up
3) Getting set up Charging the Battery The instrument normally comes with some charge in the battery, however it is recommended before initial use the battery is fully charged. Insert the charger into the mains and the charging socket into the instrument or the battery pack. -
Page 7: Horizontal Leveling
The instrument should be set on a solid base，ideally a tripod which is stable. The instrument should be attached to the tripod using the screw that inserts into the underside of the instrument. The instrument will only self level if it is set up within 5 degrees of horizontal. If the instrument appears level by eye then it should be within this range. -
Page 8: Sloping Leveling
5) Sloping Leveling a) Set up the instrument to work horizontally as shown in stages to c)on the previous page b) Press the“CAL”button to get the“X”value flashing on the screen。 c) Use the + and-buttons to get the required gradient in the “X” direction ( the X direction is Parallel to the screen/digital Panel) d) Press the “X/Y”... -
Page 9: Vertical Lines
and the unit will re- start and return to the grade previously set. 6) Vertical Lines a) Once the instrument is in the position shown above press the green button on the bottom left hand side of the Panel. b) The instrument will Auto level and start spinning giving a Vertical beam. - Page 10 b) Press the [Sean Button] for a single point c) Press the same button to get angles of approximately 10°,45°，90° and 180° d) To change the direction of the point/ scan you can Press the+ or-button to move the direction the beam is pointing B) Speed Control a) To change the speed of the rotating beam pres「Hare/Tortoise Button」.
-
Page 11: The Detector
b) When the instrument is in this mode ，there will be a signal on the LCD display to alert user that the position of the instrument has changed. 8) The Detector The detector will pick up a spinning beam when it crosses the electronic sensor window. -
Page 12: The Remote Control
9) The remote control The remote control will work to a distance of approximately 20m and is ideal for adjusting the instrument while at the same time not disturbing it. It is powered by two 1.5V AA batteries. When any of the buttons is activated a red LED light is emitted. There are 7 buttons on the remote.(There is no Power button.) The top triangle corresponds to the “CAL”... -
Page 13: Trouble Shooting
10) Trouble shooting The majority of problems that occur arise from the power source. 1) Cheek the batteries are installed correctly with the + and - in the correct orientation. 2) Check the Power rating of the batteries are correct - particularly if you are using rechargeable batteries. -
Page 14: Specifications
11) Specifications ±20〞(±3mm@30m) Accuracy ±10.00﹪ Slope range Automatic self-leveling range 5° Laser source Visible Laser Diode 635nmm Classification Class 2M or Class 3R Operational range 500m dia . (with detector) Rotational head speed 60,120,300,600,R.P.M Approximate scan angles 10°;45°;90°;180° IR Remote control Available remote distanee:20m Operation temperature -20°C~+50°C(-4°F~+122°F) -
Page 15: Warnings And Precautions
Warnings and Precautions While the instrument is in operation be careful to avoid exposing your eyes to the laser beam for long Periods. A long exposure may be hazardous to your eyesight the laser beam is equivalent to a Class 2 laser. - Page 16 Store the instrument inside its carrying ease and away from moisture，dust and vibration.(Do not store in the back of your vehicle) .Avoid sudden changes in temperature. Allow the instrument to acclimatize before use. Transport the instrument in its carrying case and always handle with Care. ...
- Page 17 Memo - 5 -...
- Page 18 Giant Precision Instrument Co., Ltd. No.16, Ln. 134, Liancheng Rd., Zhonghe Dist., New Taipei City 235, Taiwan TEL：886-2-2246-7302 FAX：886-2-2246-7301...