Sony HCD-DZ150K Service Manual page 59

QQ
3 7 63 1515 0
Pin No. Pin Name
133
134
135
136
137, 138
139 to 141 RA10, 0, 1
142 DVDD18
143, 144
145
146
147
148
149 to 155 RA11, 9 to 4
156
157 to 159 SMPTE_Y[7] to [5]
160 DVDD18
161 to 165 SMPTE_Y[4] to [0]
166
167
168
169
TE
L 13942296513 170
171 MUTE123
172, 173 REV, FWD
174 DVDD18
175 RGB_SEL
176 Fixed_low
177
178
179 VBUS_OE
180 xMAMUTE
181 VBUS_OC
182
183
184 DACVSSA
185
186 DACVDDA
187
188 DACVSSB
189
190 DACVDDB
191
192 DACVSSC
www
193
194
195
.
196 DACVDDC
197 ASDATA0
198 TRG_SW
http://www.xiaoyu163.com
I/O
RWE# O Write enable output to SDRAM (IC1104)
CAS# O Column address strobe output to SDRAM (IC1104)
RAS# O Row address strobe output to SDRAM (IC1104)
RCS# O Chip select output to SDRAM (IC1104)
BA0, 1 O Bank address 0, 1 output to SDRAM (IC1104)
O Address bus 10, 0, 1 output to SDRAM (IC1104)
— Power supply (+1.8V from IC1110)
RA2, 3 O Address bus 2, 3 output to SDRAM (IC1104)
DVDD3 — Power supply (SW+3.3V)
DRCLK O Clock output to SDRAM (IC1104)
CKE O Clock enable output to SDRAM (IC1104)
DVSS — Ground terminal
O Address bus 11,9 to 4 output to SDRAM (IC1104)
DVDD3 — Power supply (SW+3.3V)
O Video data output bit7 to 5 (not used (Open))
— Power supply (+1.8V from IC1110)
O Video data output bit4 to 0 (not used (Open))
VCLK O 27MHz synchronous clock output for Video data (not used (Open))
MIC I Karaoke microphone detect signal (H:MIC exist / L:MIC removed)
TSD_M I TSD signal input
MUTE O Mute output for Spindle motor
DVDD3 — Power supply (SW+3.3V)
O Mute output for Focus/Tracking/Sleding
O Direction control signal output for Loading motor
— Power supply (+1.8V from IC1110)
O RGB/YCbCr select output signal (H:RGB disable / L:RGB enable) (not used (Open))
O Reserved (not used (Open))
WIDE O WIDE select output for Multi connector (H:16:9 / L:4:3)
DVSS — Ground terminal
O VBUS_control OE (H:ON / L:OFF) (not used (Open))
O Main Audio Mute signal (H:Un Mute / L:Mute) (not used (Open))
I VBUS_control OC (H: Non_OVER / L:OVER) (Fixed to "H" (SW+3.3V))
R/Cr/Pr O CR/PR signal output
B/Cb/Pb O CB/PB signal output
— Ground terminal
Y/G O Y signal output
— Power supply (+3.3V from IC1105)
CVBS O Composite video signal output
— Ground terminal
C O Chroma signal output for S-Video
— Power supply (+3.3V from IC1105)
Y O Y signal output for S-Video
— Ground terminal
CIN O Compensation Capacitor (not used (Open))
x ao
FS I Full Scale Adjustment
y
VREF I Bandgap Ref Voltage
i
— Power supply (+3.3V from IC1105)
O Audio serial data 4: Down-mixed L/R
I Slot-in MECHA Triger SW detect (not used (Fixed to "H" (SW+3.3V)))
http://www.xiaoyu163.com
8
Q Q
3 6 7 1 3
u163
.
HCD-DZ150K/DZ151KB
2 9 9 4 2 8
Description
1 5 0 5 8 2 9 9 4
m
co
9 9
2 8 9 9
59