Test Mode - Sony HCD-DZ150K Service Manual

HCD-DZ150K/DZ151KB
Ver. 1.1
QQ
3 7 63 1515 0
Note: Incorrect operations may be performed if the test mode is not
entered properly.
In this case, press the ?/1 button to turn the power off, and retry
to enter the test mode.
1. Cold Reset
• The cold reset clears all data including preset data stored in
the RAM to initial conditions. Execute this mode when
returning the set to the customers.
Procedure:
1. Press the ?/1 button to turn the power on.
2. Press three buttons x , A and ?/1 simultaneously.
3. When this button is operated, display as "COLD RESET" for
a while and all of the settings are reset.
2. Panel Test Mode
• This mode is used to check the software version, FL, and KEY.
2-1. Display Test Mode
Procedure:
1. Press the ?/1 button to turn the power on.
2. Press three buttons X , . and A simultaneously.
3. When the display test mode is activated, all segments are turned
on.
4. To exit from this mode, press three buttons X , . and A
simultaneously.
2-2. Version Test Mode
Procedure:
1. When the display test mode is activated, press the . button
TE
and the message "DS1K" is displayed, the version test mode L 13942296513
is activated.
2. Whenever the . button is pressed, the display changes in
the following order.
"DS1K" (Model name) t "ASIA2
*1: ASIA2 changes depending on destination.
3. Press the > button and the date of the software production
is displayed.
4. Press the > button again and the version is displayed.
5. To exit from this mode, press three buttons X , . and A
simultaneously.
2-3. Key Test Mode
Procedure:
1. When the display test mode is activated, press the H button,
to select the key test mode.
2. To enter the KEY test mode, the fluorescent indicator displays
"K0 V0". Each time an another button is pressed, "KEY" value
increases. However, once a button is pressed, it is no longer
taken into account. When all keys are pressed correctly, "K8
V0" is displayed.
3. When the VOLUME control is turned in the direction of (+),
"V0" is changed to "V1", then ... "V9".
When the VOLUME control is turned in the direction of (–),
"V0" is changed to "V9", then ... "V1".
4. To exit from this mode, press three buttons X , . and A
simultaneously.
www
.
22
http://www.xiaoyu163.com
SECTION 4

TEST MODE

*1
" (Destination) t MC
x ao u163
y
i
http://www.xiaoyu163.com
2 9
8
3. Disc Tray Lock
The disc tray lock function for the antitheft of an demonstration
disc in the store is equipped.
Setting Procedure :
1. Press the ?/1 button to turn the power on.
2. Press the FUNCTION button to set DVD function.
3. Insert a disc.
4. Press the x button and the A button simultaneously for five
seconds.
5. The message "LOCKED" is displayed and the tray is locked.
Releasing Procedure :
1. Press the x button and the A button simultaneously for five
seconds again.
2. The message "UNLOCKED" is displayed and the tray is
unlocked.
Note: When "LOCKED" is displayed, the tray lock is not released by turning
power on/off with the ?/1 button.
4. DVD Ship Mode
Use this mode when returning the set to the customer after repair.
Procedure:
1. Press the ?/1 button to turn the power on.
2. Press the FUNCTION button to set the function "DVD".
3. Remove all discs, and then press two buttons H and ?/1
simultaneously.
4. After a message "MECHA LOCK" is displayed on the
fluorescent indicator tube, pull out the AC plug.
5. To exit from this mode, press the ?/1 button to turn the set
on.
Q Q
3 6 7 1 3 1 5
5. AM Step Change (Except for RU and E3 models)
• A step of AM channels can be changed over between 9 kHz
and 10 kHz.
Procedure:
1. Press the ?/1 button to turn the power on.
2. Select the function "TUNER", and press FUNCTION button
to select the BAND "AM".
3. Press the ?/1 button to turn the power off.
4. Press two buttons > and ?/1 simultaneously, and the
display of fluorescent indicator tube changes to "AM 9k STEP"
or "AM 10k STEP", and thus the channel step is changed over.
6. Product Out
This mode moves the optical pick-up to the position durable to
vibration and clears all data including preset data stored in the RAM
to initial conditions. Use this mode when returning the set to the
customer after repair.
Procedure:
1. Press the ?/1 button to turn the power on.
2. Press the FUNCTION button to set the function "DVD".
3. Remove all discs, and then press three buttons > , A and
?/1 simultaneously.
4. After the "STANDBY" blinking display finishes, the message
"MECHA LOCK" is displayed on the fluorescent indicator
tube disconnect the AC power plug, then the ship mode is set.
co
.
9 4 2 8
0 5 8 2 9 9 4 2 8
• Abbreviation
E3 : 220 – 240V AC area in E model
m
RU : Russian model
9 9
9 9