Page 1 When it comes to service, remember that your Toyota dealer knows your vehicle very well and is interested in your complete satisfaction. He will provide quality maintenance and any other assistance you may require. If there is not a Toyota dealer near you, or you need emergency assistance for any reason, please call the following number: Toyota Customer Assistance Center U.S.
Page 2: Important Information About This Manual
You are informed about what you must or must not do in order to avoid or reduce the risk of damage to your vehicle and its equipment. 2004 SIENNA from Aug. ’04 Prod. (OM45422U)
Page 3 04 SIENNA_U (L/O 0408) Important information about your Toyota New vehicle warranty Important health and safety information about your Toyota Your new vehicle is covered by the following Toyota limited warranties: CAUTION D New vehicle warranty D Emission control systems warranty...
Page 4 Toyota Toyota A wide variety of non−genuine spare parts and accessories The spark ignition system in your Toyota meets all require- for Toyota vehicles are currently available in the market. ments of the Canadian Interference−Causing Equipment You should know that Toyota does not warrant these prod- Standard.
Page 5 Be sure to have the systems of the SRS airbag and seat belt preten- sioner removed and disposed of by the qualified service shop or by your Toyota dealer before you dispose of your vehicle. 2004 SIENNA from Aug. ’04 Prod. (OM45422U)
Page 6 04 SIENNA_U (L/O 0408) 2004 SIENNA from Aug. ’04 Prod. (OM45422U)
Page 7: Operation Of Instruments And
........Indicator symbols on the instrument panel ..... . . 2004 SIENNA from Aug. ’04 Prod. (OM45422U)
Page 8: Instrument Panel Overview
12. Glove box 13. Power window switches 14. Power door lock switches 15. Automatic transmission selector lever 16. Audio remote control switches 17. Hood lock release lever 18. Parking brake pedal 19. Window lock switch 2004 SIENNA from Aug. ’04 Prod. (OM45422U)
Page 9: Controls
11. Cup holder and coin holder 12. Power outlets 13. Personal light main switch 14. Ignition switch 15. “TRAC OFF” switch 16. Cruise control switch or dynamic laser cruise control switch 17. Dynamic laser cruise control distance switch 2004 SIENNA from Aug. ’04 Prod. (OM45422U)
Page 10 (“SLIDE DOOR OFF” switch) 21. Power back door main switch (“BACK DOOR OFF” switch) 22. Power rear view mirror control switches 23. Power quarter window switch (“REAR VENT” switch) 24. Headlight beam level control dial 2004 SIENNA from Aug. ’04 Prod. (OM45422U)
Page 11: Instrument Cluster Overview
6. Dynamic laser cruise control master 2. Speedometer warning light 9. Odometer and two trip meters 3. Engine coolant temperature gauge 7. Dynamic laser cruise control display 10. Tachometer 4. Low fuel level warning light 2004 SIENNA from Aug. ’04 Prod. (OM45422U)
Page 12: Indicator Symbols On The Instrument Panel
∗ 1 Malfunction indicator lamp Low windshield washer fluid level warning ∗ 1 light ∗ 1 Engine oil replacement reminder light ∗ 1 Low engine oil pressure warning light (for vehicles sold in U.S.A.) 2004 SIENNA from Aug. ’04 Prod. (OM45422U)
Page 13 Traction control system off indicator light (two−wheel drive models) ∗ 2 Cruise control indicator light or dynamic laser ∗ 3 cruise control indicator light Dynamic laser cruise control ready mode indicator light Conventional cruise control mode indicator light 2004 SIENNA from Aug. ’04 Prod. (OM45422U)
Page 14 04 SIENNA_U (L/O 0408) 2004 SIENNA from Aug. ’04 Prod. (OM45422U)
Page 15: Table Of Contents
......... . . 2004 SIENNA from Aug. ’04 Prod. (OM45422U)
Page 16: Keys
If you should lose your keys or if you with a built−in transponder chip. glove box. need additional keys, duplicates can be made by a Toyota dealer using the key 2. Sub key (gray)—This key will not work To protect items locked in the glove box number.
Page 17 (includ- or may stop soon after it starts. ing keys of other vehicles) from the ring or while gripping or covering them with your hand to start the engine. 2004 SIENNA from Aug. ’04 Prod. (OM45422U)
Page 18 If you should lose your keys or if you need additional keys, duplicates can be made by a Toyota dealer using the key number. We recommend writing down the key num- ber and storing it in a safe place.
Page 19: Engine Immobilizer System
The indicator light will go off. For your Toyota dealer to make you a new key with built−in transponder chip, your dealer will need your key number and master key. However, there is a limit to the number of additional keys your Toyota dealer can make for you.
Page 20: Wireless Remote Control
Locking operation (type A) CAUTION Changes modifications pressly approved by the party respon- sible for compliance could void the user’s authority to operate the equip- ment. Unlocking operation (type A) 2004 SIENNA from Aug. ’04 Prod. (OM45422U)
Page 21 10 sec- and/or “Ignition switch light” on page 158 onds. However, if the key is in the igni- in Section 1−4.) tion, a beep will not sound. Unlocking operation (type B) 2004 SIENNA from Aug. ’04 Prod. (OM45422U)
Page 22 Right side power sliding door— To open: Push the “ ” switch. To close: Push the “ ” switch again. Right side power sliding door (type B) 2004 SIENNA from Aug. ’04 Prod. (OM45422U)
Page 23 The sliding door stops at the half−opened position when the window is opened more than about 15 cm (6 in.). The left side power sliding door does not operate when fuel filler door opened. Type B 2004 SIENNA from Aug. ’04 Prod. (OM45422U)
Page 24 ” (panic) switch is used to deter The back door is between the fully− vehicle theft when you witness anyone at- closed position and half−opened posi- tempting to break into or damage your tion. vehicle. 2004 SIENNA from Aug. ’04 Prod. (OM45422U)
Page 25 Do not leave the transmitter in places where the temperature becomes high such as on the dashboard. Do not disassemble it. Avoid knocking it hard against other objects or dropping it. Avoid putting it in water. 2004 SIENNA from Aug. ’04 Prod. (OM45422U)
Page 26 Do not bend the terminals. Toyota dealer. z Dispose of used batteries according to the local laws. Replace the transmitter battery by follow- ing these procedures: 2004 SIENNA from Aug. ’04 Prod. (OM45422U)
Page 27: Front Doors
For details, contact your Toyota deal- 2004 SIENNA from Aug. ’04 Prod. (OM45422U)
Page 28 To lock: Push the knob forward. To unlock: Pull the knob backward. The front doors can be opened by pulling the inside handles even if the lock knobs are in the locked position. 2004 SIENNA from Aug. ’04 Prod. (OM45422U)
Page 29 It also helps prevent the doors from being opened unintentionally. Front passenger’s side 2004 SIENNA from Aug. ’04 Prod. (OM45422U)
Page 30 To set function (c) opened once. Push and hold the front of the driver’s side power door lock switch for 5 sec- onds with the selector lever in any position except “P”. 2004 SIENNA from Aug. ’04 Prod. (OM45422U)
Page 31: Sliding Doors
When the vehicle is stopped on a slope, the door will slide faster when opening or closing, so be es- pecially careful that the passengers do not get hit or pinched by the door. 2004 SIENNA from Aug. ’04 Prod. (OM45422U)
Page 32 Do not leave the sliding door at half− door is opened. Otherwise, the fuel opened position. the vehicle is filler door may be damaged. stopped on a downward slope, it may move and cause an unexpected injury. 2004 SIENNA from Aug. ’04 Prod. (OM45422U)
Page 33: Power Sliding Doors
We door system is on.) To disable the pow- recommend using this feature whenever er sliding door feature, push in the small children are in the vehicle. switch. 2004 SIENNA from Aug. ’04 Prod. (OM45422U)
Page 34 To unlock: Move the knob backward. Closing the sliding door with the lock knob in the lock position will also lock the slid- ing door. Be careful not to lock your keys in the vehicle. 2004 SIENNA from Aug. ’04 Prod. (OM45422U)
Page 35 When the vehicle is stopped on a slope, the door will slide faster when opening or closing, so be es- pecially careful that the passengers do not get hit or pinched by the door. 2004 SIENNA from Aug. ’04 Prod. (OM45422U)
Page 36 Otherwise, the fuel opened position because the door will filler door may be damaged. unlock after 30 minutes. If the vehicle is stopped on a downward slope, it may move and cause an unexpected injury. 2004 SIENNA from Aug. ’04 Prod. (OM45422U)
Page 37 We recommend using this not to get your fingers trapped as feature whenever small children are in the the sliding door automatically opens vehicle. or closes. Never allow a child to operate the sliding door. 2004 SIENNA from Aug. ’04 Prod. (OM45422U)
Page 38 The sliding door is unlocked. The power sliding door system is on. (The “SLIDE DOOR OFF” switch is pushed out.) The sliding door is between the fully− closed position and half−opened posi- tion. Center pillar 2004 SIENNA from Aug. ’04 Prod. (OM45422U)
Page 39 The length of time required to push the manually by the outside or inside handle. switches for operating the sliding door can be changed. For details, contact your Toyota dealer. 2004 SIENNA from Aug. ’04 Prod. (OM45422U)
Page 40 Never try jamming any part of your than 2 times, the sliding door will be body to make the jam protection stopped at that position and the power function work intentionally. sliding door system will be canceled. 2004 SIENNA from Aug. ’04 Prod. (OM45422U)
Page 41: Back Door
Operate the power door lock switch. (See “Front doors” on page 21 in this Section.) Operate the wireless remote control. (See “Wireless remote control” on page 14 in this Section.) 2004 SIENNA from Aug. ’04 Prod. (OM45422U)
Page 42: Power Back Door
To disable the pow- See “—Stowage precautions” on page 389 back door feature, push in Section 2 for precautions when loading switch. luggage. 2004 SIENNA from Aug. ’04 Prod. (OM45422U)
Page 43 (See “Wireless remote control” on page 14 in this Section.) All the side doors and back door are locked unlocked simultaneously with the driver’s door. (See “Front doors” on page 21 in this Section.) 2004 SIENNA from Aug. ’04 Prod. (OM45422U)
Page 44 Otherwise, the back door closer may try pulling it up to make sure it is secure- be damaged. ly closed. See “—Stowage precautions” on page 389 in Section 2 for precautions when loading luggage. 2004 SIENNA from Aug. ’04 Prod. (OM45422U)
Page 45 Careful attention is needed so as this switch once again. The door opens not to get your fingers trapped as and closes completely. the back door automatically closes. Never allow a child to operate the back door. 2004 SIENNA from Aug. ’04 Prod. (OM45422U)
Page 46 For details, contact your tion. stopped at that position. Toyota dealer. The time of pushing the switches for oper- ating the back door can be changed. For details, contact your Toyota dealer. 2004 SIENNA from Aug. ’04 Prod. (OM45422U)
Page 47 When anyone closes the power back door, make sure he or she operates the door safely. 2004 SIENNA from Aug. ’04 Prod. (OM45422U)
Page 48: Power Windows
Key off operation: If both front doors are closed, the front door windows and sliding door windows work for 43 seconds even after the ignition switch is turned off. It stops working when either front door is opened. 2004 SIENNA from Aug. ’04 Prod. (OM45422U)
Page 49 If the window receives a strong impact, checked by your Toyota dealer. this function may work even if nothing is caught. Type B (to open and close) 2004 SIENNA from Aug. ’04 Prod. (OM45422U)
Page 50 Never try jamming any part of your body to activate the jam protection function intentionally. The jam protection function may not work if something gets caught just before the window fully closed. 2004 SIENNA from Aug. ’04 Prod. (OM45422U)
Page 51 When small children are in the ve- hicle, never let them use the power window switches without supervi- sion. Use the window lock switch to prevent them from making unex- pected use of the switches. 2004 SIENNA from Aug. ’04 Prod. (OM45422U)
Page 52: Manual Quarter Windows
When small children are in the ve- Both the left and right rear quarter win- hicle, never let them use the power dows move as long as you hold the quarter window switches without switch. supervision. 2004 SIENNA from Aug. ’04 Prod. (OM45422U)
Page 53: Hood
CAUTION Before driving, be sure that the hood is closed and securely locked. Other- wise, the hood may open unexpected- ly while driving and an accident may occur. 2004 SIENNA from Aug. ’04 Prod. (OM45422U)
Page 54: Theft Deterrent System
Then lower the hood and make sure it locks into place. If necessary, press down gently on the front edge to lock it. 2004 SIENNA from Aug. ’04 Prod. (OM45422U)
Page 55 3. Close and lock all the side doors, back door and hood. The indicator light will remain on when all the side doors, back door and hood are closed and locked. 2004 SIENNA from Aug. ’04 Prod. (OM45422U)
Page 56: Fuel Tank Cap
If the system does not work properly, have it checked by your Toyota dealer. 2004 SIENNA from Aug. ’04 Prod. (OM45422U)
Page 57 When opening the cap, do not re- move the cap quickly. In hot weath- er, fuel under pressure could cause injury by spraying out of the filler neck if the cap is suddenly re- moved. 2004 SIENNA from Aug. ’04 Prod. (OM45422U)
Page 58 Make sure the cap is tightened securely. The indicator lamp goes off after driving several times. If the indicator lamp does not go off, contact your Toyota dealer as soon as possible. CAUTION 3. The removed cap can be stored on Make sure the cap is installed se- the back side of the fuel filler door.
Page 59: Electric Moon Roof
To close: Push the switch on the “TILT When you quickly push and release the UP” side. switch, the moon roof will tilt down while Tilting operation the switch is being pushed and stop when released. 2004 SIENNA from Aug. ’04 Prod. (OM45422U)
Page 60 “TILT UP” side until make sure it is safe to do so. the moon roof tilts all the way up and then tilts down a little automatically. 2004 SIENNA from Aug. ’04 Prod. (OM45422U)
Page 61 ..........2004 SIENNA from Aug. ’04 Prod. (OM45422U)
Page 62: Seats
Move your seat to the rear as far as you can while still reaching the pedals comfortably. 2004 SIENNA from Aug. ’04 Prod. (OM45422U)
Page 63 2004 SIENNA from Aug. ’04 Prod. (OM45422U)
Page 64 To change the seat height, turn the knob either way. 3. SEATBACK ANGLE ADJUSTING LEVER Lean forward and pull the lever up. Then lean back to the desired angle and release the lever. 2004 SIENNA from Aug. ’04 Prod. (OM45422U)
Page 65 Releasing the switch will stop the seat- back at that position. 4. SEAT LUMBAR SUPPORT ADJUSTING KNOB To change the amount of lumber sup- port, turn the knob either way. 2004 SIENNA from Aug. ’04 Prod. (OM45422U)
Page 66 In the event of a frontal collision, the more the seat is re- clined, the greater the risk of death or personal injury. 2004 SIENNA from Aug. ’04 Prod. (OM45422U)
Page 67 1. Pull the seatback angle adjusting le- 2. Pull the seatback folding lever and ver and raise the seatback to its up- fold the seatback down. right position. 2004 SIENNA from Aug. ’04 Prod. (OM45422U)
Page 68: Rear Seats
Do not sit on the folded seatback. Make sure the front passenger’s seat is securely locked in sliding position when you set the seat as a temporary table. 2004 SIENNA from Aug. ’04 Prod. (OM45422U)
Page 69 Folding the seats up will enlarge the lug- gage compartment. See “—Stowage pre- cautions” on page 389 in Section 2 for precautions when loading luggage. Outer seat Center seat 2004 SIENNA from Aug. ’04 Prod. (OM45422U)
Page 70 After passengers are in, return the seat until it locks securely, and lift up the seat back by pulling the lever or strap. 2004 SIENNA from Aug. ’04 Prod. (OM45422U)
Page 71 (position 2) to its from operating properly. tumbled position (position 1), you must return the folded−down seat (position 2) original position (position 3) once. (It is possible to operate the seat in the order 1→2→3→1.) 2004 SIENNA from Aug. ’04 Prod. (OM45422U)
Page 72 The seat belt must be removed from To prevent damage to the seat belt the hanger when the seat belt is in buckles, the buckles must be stowed use. before you fold the seatback. 2004 SIENNA from Aug. ’04 Prod. (OM45422U)
Page 73 The holding strap must be stowed damaged if the seat hits them. into the pocket when it is not in To avoid serious injury, do not sit use. on the folded seatback. 2004 SIENNA from Aug. ’04 Prod. (OM45422U)
Page 74 When you fold down the seatback from its putting heavy loads on the temporary upright position, the rear leg locks will table. disengage. In this case, lift up the seat and fold down again to engage the rear leg locks. 2004 SIENNA from Aug. ’04 Prod. (OM45422U)
Page 75 Make sure the seat belts are not twisted or caught in the seatback and are arranged in their proper position and are ready to use. 2004 SIENNA from Aug. ’04 Prod. (OM45422U)
Page 76 If the seat is not in the rear−most lock position, the rear leg will not unlock. In this case, slide the seat to the rear−most lock position and then do the above op- eration again. 2004 SIENNA from Aug. ’04 Prod. (OM45422U)
Page 77 NOTICE z Do not use anything other than the assist grip to hold the second seat. z The holding strap must be stowed into the pocket when it is not in use. 2004 SIENNA from Aug. ’04 Prod. (OM45422U)
Page 78 Make sure the second seat is se- and are arranged in their proper curely locked in position when you position and are ready to use. set the second seat as a temporary table. 2004 SIENNA from Aug. ’04 Prod. (OM45422U)
Page 79 The seat belt must be removed from To prevent damage to the seat belt the hanger when the seat belt is in buckles, the buckles must be stowed use. before you fold the seatback. 2004 SIENNA from Aug. ’04 Prod. (OM45422U)
Page 80 Be careful not to get your hands or on the folded seatback. feet pinched in the seat. Be careful not to hit the removed seat against a person or drop it on yourself. 2004 SIENNA from Aug. ’04 Prod. (OM45422U)
Page 81 Otherwise, the seat may slide and not installed properly. If you slide the removed seat, return the seat to the rear−most position be- fore it is installed. 7−passenger models 8−passenger models 2004 SIENNA from Aug. ’04 Prod. (OM45422U)
Page 82 NOTICE You must install the seat in its origi- nal position. If it is installed in the wrong position, the seat lock or bezel will be damaged. 2004 SIENNA from Aug. ’04 Prod. (OM45422U)
Page 83 If you align the legs with the front front legs will reach the striker. Make sure strikers, the bezel in the floor will be the front legs align with the striker, swing damaged. up the seat. 2004 SIENNA from Aug. ’04 Prod. (OM45422U)
Page 84 Failure to do so will prevent the seat belt from oper- ating properly. 2004 SIENNA from Aug. ’04 Prod. (OM45422U)
Page 85 Otherwise, the seat may slide and not be installed properly. If you slide the removed seat, return the seat to the rear−most position before it is installed. 2004 SIENNA from Aug. ’04 Prod. (OM45422U)
Page 86 In lever and pull it up. Then slide the this case, slide the seat to the rear−most seat to the rear−most lock position. lock position and then do the above op- eration again. 2004 SIENNA from Aug. ’04 Prod. (OM45422U)
Page 87 Do not leave removed seat loose in the vehicle. Do not try to sit on or place any- thing on the removed seat. 2004 SIENNA from Aug. ’04 Prod. (OM45422U)
Page 88 NOTICE You must install the seat in its origi- nal position. If it is installed in the wrong position, the seat lock or bezel will be damaged. 2004 SIENNA from Aug. ’04 Prod. (OM45422U)
Page 89 Then slide the seat forward along the groove of the bezel until the front legs will reach the striker. Make sure the front legs align with the striker, swing up the seat. 2004 SIENNA from Aug. ’04 Prod. (OM45422U)
Page 90 If you align the legs with the front strikers, the bezel in the floor will be damaged. 2004 SIENNA from Aug. ’04 Prod. (OM45422U)
Page 91 POSITION lease lever and fold the table down. 1. Slide the front seats forward from the rear−most position, stand the seatbacks to the upright position. 2004 SIENNA from Aug. ’04 Prod. (OM45422U)
Page 92 (center seat)” on page 80 in this Section.) Align the front leg hook with the rear striker of the forward pair. Then swing the seat until it reaches the folded seat side table. 2004 SIENNA from Aug. ’04 Prod. (OM45422U)
Page 93 Failure to do so will prevent the seat belt from oper- ating properly. 2004 SIENNA from Aug. ’04 Prod. (OM45422U)
Page 94 The seat belt must be stowed before belt. In the event of a frontal colli- you fold the seatback. sion, the more the seat is reclined, the greater the risk of death or per- sonal injury. 2004 SIENNA from Aug. ’04 Prod. (OM45422U)
Page 95 04 SIENNA_U (L/O 0408) STOWING THIRD SEATS 2. Pull the seatback angle adjusting strap (“TO FOLD/LIFT SEATBACK” 1. Lower the head restraint to the low- printed on its surface), then fold est position. down the seatback. 2004 SIENNA from Aug. ’04 Prod. (OM45422U)
Page 96 Lift the seatback by pulling on the seat- back angle adjusting strap (“TO FOLD/ LIFT SEATBACK” printed on its surface). Then push the seatback down again. 2004 SIENNA from Aug. ’04 Prod. (OM45422U)
Page 97 (“TO FOLD/ strap (“TO FOLD/LIFT SEATBACK” LIFT SEATBACK” printed on its surface). printed on its surface) and raise the Then push the seatback down again. seatback. 2004 SIENNA from Aug. ’04 Prod. (OM45422U)
Page 98 It may cause an acci- dent or severe injury in the event of emergency braking or collision. 2004 SIENNA from Aug. ’04 Prod. (OM45422U)
Page 99: Head Restraints
To prevent damage to the armrest, After adjusting the head restraint, avoid putting heavy loads on it. make sure it is locked in position. Do not drive with the head re- straints removed. Third seats 2004 SIENNA from Aug. ’04 Prod. (OM45422U)
Page 100: Seat Heaters
To turn it off, move the dial downward until it stops. When the seat heater is not in use, move the dial fully downward. The key must be in the “ON” position to operate seat heaters. 2004 SIENNA from Aug. ’04 Prod. (OM45422U)
Page 101: Seat Belts
Inspect the belt system periodically. tion of the airbag may cause death or Check for cuts, fraying, and loose serious injury to the child. parts. Damaged parts should be re- placed. disassemble modify the system. 2004 SIENNA from Aug. ’04 Prod. (OM45422U)
Page 102 Toyota dealer. Do not use the seat slow, easy motion will allow the belt to until the seat belt is fixed. It cannot extend, and you can move around freely. protect an adult occupant or your child from injury. 2004 SIENNA from Aug. ’04 Prod. (OM45422U)
Page 103 Always wear the belt with the shoul- der portion over the outside armrest and the lap portion under the outside armrest. Failure to do so may in- crease the chance of injury in an ac- cident. 2004 SIENNA from Aug. ’04 Prod. (OM45422U)
Page 104 Then portion upward through the latch plate. make sure it remains untwisted as it re- tracts. 2004 SIENNA from Aug. ’04 Prod. (OM45422U)
Page 105 Buckle 1—Properly matches with hooked operation. end tab Make sure buckle securely Buckle 2—Properly matches with round latched for ready use of the center seat end tab belt of the third seats. 2004 SIENNA from Aug. ’04 Prod. (OM45422U)
Page 106 Do not use the center seat belt of the third seats with either buckle re- leased. Fastening only the shoulder belt or lap belt may cause serious personal injury in case of a sudden braking or a collision. Third 2004 SIENNA from Aug. ’04 Prod. (OM45422U)
Page 107 (See “—Stowing third seats” on page 88 in this Section.) NOTICE Stow the center seat belt of the third seats except when you are wearing it. 2004 SIENNA from Aug. ’04 Prod. (OM45422U)
Page 108 Be sure to another person, or at a different wear the seat belt with the seat belt seating position than the one origi- extender. nally intended. 2004 SIENNA from Aug. ’04 Prod. (OM45422U)
Page 109 This helps prevent crosses the shoulder. damage to the vehicle interior and extend- er itself. When not in use, remove the extender and store in the vehicle for future use. 2004 SIENNA from Aug. ’04 Prod. (OM45422U)
Page 110 The seat belt pretensioners and SRS air- details, see “Service reminder indicators bags may not operate together in case of and warning buzzers” on page 167 in Sec- collisions at certain speeds and angles. tion 1−5.) 2004 SIENNA from Aug. ’04 Prod. (OM45422U)
Page 111 Repairs made on or near the front trolled by the airbag sensor assembly. The fenders, front end structure or con- airbag sensor assembly consists of a saf- sole ing sensor and airbag sensor. 2004 SIENNA from Aug. ’04 Prod. (OM45422U)
Page 112: Srs Driver Airbag And Front Passenger Airbag
Be sure to wear your seat belt properly. front seat belt pretensioner. 2004 SIENNA from Aug. ’04 Prod. (OM45422U)
Page 113 (For details, see “Service reminder indicators and warning buzzers” on page 167 in Sec- tion 1−5.) 2004 SIENNA from Aug. ’04 Prod. (OM45422U)
Page 114 SRS front airbags and the seat belt pretensioners may not activate together. For the safety of all occupants, always wear your seat belts properly. 2004 SIENNA from Aug. ’04 Prod. (OM45422U)
Page 115 The windshield may be damaged by 7. Airbag module for driver absorbing some of the force of the inflat- (airbag and inflator) ing airbag. The airbag sensor assembly consists of a safing sensor and airbag sensor. 2004 SIENNA from Aug. ’04 Prod. (OM45422U)
Page 116 “Seat belts” on page 95 in this Sec- tion. 2004 SIENNA from Aug. ’04 Prod. (OM45422U)
Page 117 Sit up straight and well back bag could cause death or serious in the seat, and always use your injury to the child. seat belt properly. 2004 SIENNA from Aug. ’04 Prod. (OM45422U)
Page 118 For instruc- hold objects in their arms or on tions concerning the installation of their knees. a child restraint system, see “Child restraint” on page 121 in this Sec- tion. 2004 SIENNA from Aug. ’04 Prod. (OM45422U)
Page 119 Contact your bar, kangaroo bar, etc.), snowplow, The front of the vehicle (shaded in the Toyota dealer as soon as possible to ser- winches or any other equipment to illustration) was involved in an accident vice the vehicle.
Page 120: Srs Side Airbags And Curtain Shield Airbags
SRS side airbags and curtain shield airbags are inflated. 2004 SIENNA from Aug. ’04 Prod. (OM45422U)
Page 121 For the safety of all occupants, always connecting wiring and power sources. (For wear your seat belts properly. details, see “Service reminder indicators and warning buzzers” on page 167 in Sec- tion 1−5.) 2004 SIENNA from Aug. ’04 Prod. (OM45422U)
Page 122 5. Side and curtain shield airbag sensors inflate with considerable force. While the system is designed to reduce serious inju- 6. Airbag sensor assembly ries, it may also cause minor burns or abrasions and swelling. 2004 SIENNA from Aug. ’04 Prod. (OM45422U)
Page 123 For instructions and precautions concerning seat belt system, see “Seat belts” on page 95 in this Section. 2004 SIENNA from Aug. ’04 Prod. (OM45422U)
Page 124 Do not apply excessive weight to the outer side of the front seats with a side airbag, and to the front pillar, rear pillar and roof side rail with a curtain shield airbag. 2004 SIENNA from Aug. ’04 Prod. (OM45422U)
Page 125 2004 SIENNA from Aug. ’04 Prod. (OM45422U)
Page 126 The light comes on or flashes while Such changes may disable the sys- driving. tem or cause the curtain shield air- bags to inflate accidentally, result- ing in death or serious injury. 2004 SIENNA from Aug. ’04 Prod. (OM45422U)
Page 127: Child Restraint
(padding) containing the curtain shield airbags in- side (shaded illustration) scratched, cracked, or otherwise dam- aged. NOTICE Do not disconnect the battery cables before contacting your Toyota dealer. 2004 SIENNA from Aug. ’04 Prod. (OM45422U)
Page 128 In the event of an accident, the force of the rapid inflation of the airbag can cause death or serious injury if a rear−facing child restraint system is installed on the front seat. 2004 SIENNA from Aug. ’04 Prod. (OM45422U)
Page 129 This will prevent it from in- juring passengers in the event of a sud- den stop or accident. 2004 SIENNA from Aug. ’04 Prod. (OM45422U)
Page 130 135 in this Section. The child restraint lower anchorages ap- proved for your vehicle may also be used. See “—Installation with child restraint low- er anchorages” on page 138 in this Sec- tion. (B) Convertible seat 2004 SIENNA from Aug. ’04 Prod. (OM45422U)
Page 131 If the driver’s seat position does not allow sufficient space for safe installation, install child straint system on the second right seat. 2004 SIENNA from Aug. ’04 Prod. (OM45422U)
Page 132 Otherwise, taking care not to twist the belt. Keep child restraint system cannot be se- the lap portion of the belt tight. curely restrained this cause death or serious injuries in a collision. 2004 SIENNA from Aug. ’04 Prod. (OM45422U)
Page 133 To hold the infant seat securely, make it is secure. Follow all the installation sure the belt is in the lock mode before instructions provided by its manufac- letting the belt retract. turer. 2004 SIENNA from Aug. ’04 Prod. (OM45422U)
Page 134 2004 SIENNA from Aug. ’04 Prod. (OM45422U)
Page 135 If the driver’s seat position does not allow sufficient space for safe installation, install child straint system on the second right seat. 2004 SIENNA from Aug. ’04 Prod. (OM45422U)
Page 136 Keep the lap portion of the belt curely restrained this tight. cause death or serious injuries in a collision. 2004 SIENNA from Aug. ’04 Prod. (OM45422U)
Page 137 To hold the convertible seat securely, it is secure. Follow all the installation make sure the belt is in the lock mode instructions provided by its manufac- before letting the belt to retract. turer. 2004 SIENNA from Aug. ’04 Prod. (OM45422U)
Page 138 A booster seat is used in forward−fac- belt to retract completely. The belt will ing position only. move freely again and be ready to work for an adult or older child passen- ger. 2004 SIENNA from Aug. ’04 Prod. (OM45422U)
Page 139 Make sure the shoulder belt is correctly collision. across the child’s shoulder and that the lap belt is positioned as low as possible on the child’s hips. See “Seat belts” on page 95 in this Section for details. 2004 SIENNA from Aug. ’04 Prod. (OM45422U)
Page 140 Do not insert coins, clips, etc. in the buckle as this may prevent your child from properly latching the tab and buckle. 2004 SIENNA from Aug. ’04 Prod. (OM45422U)
Page 141 Anchor bracket is installed for each sec- ond seating position. Anchor brackets 7−passenger models Follow the procedure below for a child restraint system that requires the use of a top strap. Anchor brackets 8−passenger models 2004 SIENNA from Aug. ’04 Prod. (OM45422U)
Page 142 Make sure the top strap is securely latched, and check that the child re- straint system is secure by pushing and pulling it in different directions. Follow all the installation instructions provided by its manufacturer. 2004 SIENNA from Aug. ’04 Prod. (OM45422U)
Page 143 1. Remove the head restraint. of a top strap. Anchor bracket is installed for right side and center seating position. 2004 SIENNA from Aug. ’04 Prod. (OM45422U)
Page 144 Latch hook onto the anchor turer. bracket and tighten the top strap. For instructions to install the child re- straint system, see “Child restraint” on page 121 in this Section. 8−passenger models 2004 SIENNA from Aug. ’04 Prod. (OM45422U)
Page 145 1st lock position (most upright position) and then to the 5th lock position. Make sure the seat and seatback is locked securely. Canada only Type A (anchor position indicated by buttons) 2004 SIENNA from Aug. ’04 Prod. (OM45422U)
Page 146 04 SIENNA_U (L/O 0408) Canada only Canada only Canada only Type A (anchor position indicated by Type B (anchor position indicated by Type B (anchor position indicated by tags) buttons) tags) 2004 SIENNA from Aug. ’04 Prod. (OM45422U)
Page 147 CMVSS213 specification den braking or a collision. can be fixed to these anchorages. In this case, it is not necessary to fix the child restraint system with a seat belt on the vehicle. 2004 SIENNA from Aug. ’04 Prod. (OM45422U)
Page 148 1st lock position (most upright position) until it locks into place. Adjust the seatback to the 11th lock position. Make sure the seatback is locked secure- Canada only Canada only Type A Type B 2004 SIENNA from Aug. ’04 Prod. (OM45422U)
Page 149: Tilt And Telescopic Steering Wheel
This can cause death or seri- lock release lever. tion manual equipped with each product. ous injury to the child and front passenger in case of sudden brak- ing or a collision. 2004 SIENNA from Aug. ’04 Prod. (OM45422U)
Page 150: Outside Rear View Mirrors
On some models, since the mirror surfaces can get hot, do not touch them when the defogger switch is 2004 SIENNA from Aug. ’04 Prod. (OM45422U)
Page 151 Both the driver and pas- Mirrors can be adjusted when the key is senger side rear view mirrors must in the “ACC” or “ON” position. be extended and properly adjusted before driving. 2004 SIENNA from Aug. ’04 Prod. (OM45422U)
Page 152: Anti−Glare Inside Rear View Mirror
Night driving—Lever at position 2 mode. Remember that by reducing glare you also The indicator illuminates to show you that lose some rear view clarity. the function is on. 2004 SIENNA from Aug. ’04 Prod. (OM45422U)
Page 153: Vanity Mirrors
20 minutes. hicle and an accident may occur re- sulting in death or serious injuries. 2004 SIENNA from Aug. ’04 Prod. (OM45422U)
Page 154 Turning off all the “ON” lights. All the lights are cut off when all the side doors and back door are locked by key or wireless remote control transmitter. The ignition switch must be turned off. 2004 SIENNA from Aug. ’04 Prod. (OM45422U)
Page 155 ....... . . 2004 SIENNA from Aug. ’04 Prod. (OM45422U)
Page 156: Headlights And Turn Signals
The lights automatically turn off when the for a long period when the engine is driver’s door is opened with the ignition not running. key in the “ACC” or “LOCK” position. 2004 SIENNA from Aug. ’04 Prod. (OM45422U)
Page 157 2004 SIENNA from Aug. ’04 Prod. (OM45422U)
Page 158 Position 1 or position 3 with the tail not running. lights on— The lights automatically turn off when the driver’s door is opened with the ignition key in the “ACC” or “LOCK” position. 2004 SIENNA from Aug. ’04 Prod. (OM45422U)
Page 159: Headlight Beam Level Control
“OFF”. lights) on the instrument panel flash faster dazzle other road users. than normal, a front or rear turn signal bulb is burned out. 2004 SIENNA from Aug. ’04 Prod. (OM45422U)
Page 160: Emergency Flashers
Always pull as far off the road as pos- sible. The turn signal light switch will not work when the emergency flashers are operat- ing. 2004 SIENNA from Aug. ’04 Prod. (OM45422U)
Page 161: Instrument Panel Light Control
To turn on the front fog lights, twist ment panel lights, turn the knob. the band of the headlight and turn sig- nal switch lever. They will come on only when the headlights are on low beam. 2004 SIENNA from Aug. ’04 Prod. (OM45422U)
Page 162: Front Personal Lights
All the side doors and back door are closed when the ignition key is in the “ACC” or “ON” position. All the side doors and back door are closed and locked. Personal light main switch 2004 SIENNA from Aug. ’04 Prod. (OM45422U)
Page 163: Rear Personal Lights
“DOOR” position When both the sliding doors and back for 20 minutes or more. door are closed, the lights can be turned on or off by pushing each lens. Personal light main switch 2004 SIENNA from Aug. ’04 Prod. (OM45422U)
Page 164: Luggage Compartment Light
All the side doors and back door are closed when the ignition key is in the “ACC” or “ON” position. All the side doors and back door are closed and locked. Personal light main switch 2004 SIENNA from Aug. ’04 Prod. (OM45422U)
Page 165: Windshield Wipers And Washer
Position 3 Fast Do not operate the wipers if the wind- shield is dry. It may scratch the For a single sweep of the windshield, glass. push the lever up and release it. 2004 SIENNA from Aug. ’04 Prod. (OM45422U)
Page 166: Rear Window Wiper And Washer
(position 3 or 4). The knob automatically returns from these positions after you release it. For instructions on adding washer fluid, see “Adding washer fluid” on page 479 in Section 7−3. 2004 SIENNA from Aug. ’04 Prod. (OM45422U)
Page 167: Rear Window And Outside Rear View Mirror Defoggers And Windshield Wiper De−Icer
Vehicles with the wind- damage the heater wires or connec- shield wiper de−icer, the windshield wiper tors. blades will be de−iced. 2004 SIENNA from Aug. ’04 Prod. (OM45422U)
Page 168 04 SIENNA_U (L/O 0408) 2004 SIENNA from Aug. ’04 Prod. (OM45422U)
Page 169 ....... . Service reminder indicators and warning buzzers ....2004 SIENNA from Aug. ’04 Prod. (OM45422U)
Page 170: Fuel Gauge
The indicator lamp goes off after driving several times. If the indicator lamp does not go off, contact your Toyota dealer as soon as possible. It is not a malfunction even if the needle of the fuel gauge returns to “E” when the...
Page 171: Tachometer
It is not a malfunction even if the needle of the tachometer returns to the bottom position when the ignition switch is turned to the “START” position. 2004 SIENNA from Aug. ’04 Prod. (OM45422U)
Page 172: Odometer And Two Trip Meters
You can use one trip meter to calculate the fuel economy and the other to measure the distance on each trip. All trip meter data is cancelled if the elec- trical power source is disconnected. 2004 SIENNA from Aug. ’04 Prod. (OM45422U)
Page 173: Service Reminder Indicators And Warning Buzzers
04 SIENNA_U (L/O 0408) Service reminder indicators and warning buzzers If the indicator or buzzer comes on... Do this. If parking brake is off, stop immediately and contact Toyota dealer. Fasten driver’s seat belt. (indicator and buzzer) Fasten front passenger’s seat belt.
Page 174 If the indicator or buzzer comes on... Do this. Take vehicle to Toyota dealer. If brake system warning light is also on, stop immediately and contact Toyota dealer. Close all doors. Take vehicle to Toyota dealer immediately. Take vehicle to Toyota dealer.
Page 175 If the indicator or buzzer comes on... Do this. Dynamic laser cruise control Check the condition according to the warning code. If the system malfunctions, contact Toyota dealer. master warning light Key reminder buzzer Remove key. 2004 SIENNA from Aug. ’04 Prod. (OM45422U)
Page 176 A warning light turning on briefly during light to come on. operation does not indicate a problem. 2004 SIENNA from Aug. ’04 Prod. (OM45422U)
Page 177: Discharge Warning Light
Have your vehicle Empty fuel tank checked by your Toyota dealer as soon as If the fuel tank is empty, refuel immedi- possible. ately. 2004 SIENNA from Aug. ’04 Prod. (OM45422U)
Page 178: Low Engine Oil Pressure Warning Light
In this case, the wheels could lock up indicate low oil level, and the oil level during a sudden braking or braking on must be checked using the level dipstick. slippery road surfaces. 2004 SIENNA from Aug. ’04 Prod. (OM45422U)
Page 179 The light does not come on when the ble during braking. ignition key is turned to the “ON” posi- tion or remains on. The light comes on or flashes while driving. 2004 SIENNA from Aug. ’04 Prod. (OM45422U)
Page 180 “TRAC OFF” switch is not pushed. The light warns that the windshield washer fluid level is too low. Add washer fluid at your earliest opportunity. (For instructions, see “Adding washer fluid” on page 479 in Section 7−3.) 2004 SIENNA from Aug. ’04 Prod. (OM45422U)
Page 181 If any service reminder indicator or warn- ing buzzer does not function as described above, have it checked by your Toyota dealer as soon as possible. 2004 SIENNA from Aug. ’04 Prod. (OM45422U)
Page 182 04 SIENNA_U (L/O 0408) 2004 SIENNA from Aug. ’04 Prod. (OM45422U)
Page 183 ....... . . 2004 SIENNA from Aug. ’04 Prod. (OM45422U)
Page 184: Ignition Switch With Steering Lock
Once you remove the key, the engine im- turned to the “START” position. mobilizer system is automatically set. (See “Engine immobilizer system” on page 13 in Section 1−2.) 2004 SIENNA from Aug. ’04 Prod. (OM45422U)
Page 185: Automatic Transmission
4: Engine braking (shifting into overdrive not possible) 3, 2: Stronger engine braking Shift with the brake pedal L: Maximum engine braking depressed. (The ignition switch must be in “ON” position.) Shift normally. 2004 SIENNA from Aug. ’04 Prod. (OM45422U)
Page 186 Two−wheel drive models 3. Release the parking brake and brake 91 km/h (57 mph) pedal. Depress the accelerator pedal All−wheel drive models slowly for smooth starting. 88 km/h (55 mph) 2004 SIENNA from Aug. ’04 Prod. (OM45422U)
Page 187 3. With the brake pedal pressed down, shift the selector lever to the “P” posi- tion. 2004 SIENNA from Aug. ’04 Prod. (OM45422U)
Page 188: Traction Control System
CAUTION speed for the present road condi- tions. Always keep your foot on the brake pedal while stopped with the engine running. This prevents the vehicle from creeping. 2004 SIENNA from Aug. ’04 Prod. (OM45422U)
Page 189 The vehicle stability control system is al- ways activated, even if the traction control system is turned off. To turn on: Push “TRAC OFF” switch once again. The “TRAC OFF” indicator light will go off. 2004 SIENNA from Aug. ’04 Prod. (OM45422U)
Page 190 “ON” and will go off after a few seconds. If the light comes on while driving, the system does not work. However, as con- ventional braking operates when applied, there is no problem to continue your driv- ing. 2004 SIENNA from Aug. ’04 Prod. (OM45422U)
Page 191 This means drive at an appropriate and cautious that the traction control system is in the speed for the present road condi- self−check mode, but does not indicate a tions. malfunction. 2004 SIENNA from Aug. ’04 Prod. (OM45422U)
Page 192: Vehicle Stability Control System
“ON” and will go off after a few seconds. If the light comes on while driving, the system does not work. However, as con- ventional braking operates when applied, there is no problem to continue your driv- ing. 2004 SIENNA from Aug. ’04 Prod. (OM45422U)
Page 193 “Checking and replacing tires” on contact your Toyota dealer. system does not work. However, as con- page 466 in Section 7−2.) ventional braking operates when applied, there is no problem to continue your driv- ing. 2004 SIENNA from Aug. ’04 Prod. (OM45422U)
Page 194: Tire Pressure Warning System
If the warning light comes on: Vehicles with standard tires— Adjust the tire pressure to the specified level as soon as possible. (See “Tires” on page 491 in Section 8.) 2004 SIENNA from Aug. ’04 Prod. (OM45422U)
Page 195 20 psi), con- roads. The low tire pressure warning system sult your Toyota dealer. If the tire is needs to be initialized. Reset the system The vehicle speed is less than 30 km/h flat or the tire pressure is below 100...
Page 196 If the vehicle dard. tires deteriorate, you could lose control of the steering wheel or the brakes, causing death or serious in- jury. 2004 SIENNA from Aug. ’04 Prod. (OM45422U)
Page 197 If you push the reset switch while the vehicle is moving, initialization is not per- formed. 2004 SIENNA from Aug. ’04 Prod. (OM45422U)
Page 198: Parking Brake
Avoid vehicle speed increases when driving downhill. vehicle speed is too fast in relation to the cruise control set speed, cancel the cruise control then downshift the transmission to use engine braking to slow down. Type B 2004 SIENNA from Aug. ’04 Prod. (OM45422U)
Page 199 To use tap changes the set speed by 1.6 km/h cruise control again, press the “ON−OFF” (1.0 mph). You can now take your foot off button again to turn it on. the accelerator pedal. 2004 SIENNA from Aug. ’04 Prod. (OM45422U)
Page 200 If this is the case, contact your Toyota pedal. If you use the brake pedal, cruise dealer and have your vehicle inspected. control is cancelled.
Page 201: Dynamic Laser Cruise Control
Steering wheel not use cruise control except in ap- propriate road and traffic conditions. Always drive carefully and attentively. Before using dynamic laser cruise control, read and understand the fol- lowing instructions. Instrument cluster 2004 SIENNA from Aug. ’04 Prod. (OM45422U)
Page 202 “—Conventional (fixed speed) conditions while using dynamic laser cruise control mode” on page 207. cruise control. Conventional (fixed speed) cruise control mode 2004 SIENNA from Aug. ’04 Prod. (OM45422U)
Page 203 VEHICLE DISTANCE” on page 203. 4. Acceleration cruising function: If the vehicle ahead changes lanes, your ve- hicle cruising speed will be gradually increased up to the preset speed, and your vehicle resumes fixed−speed cruising. 2004 SIENNA from Aug. ’04 Prod. (OM45422U)
Page 204 When using the windshield wipers ing the nose of your vehicle to tilt at high or low speeds the dynamic laser radar cruise control turns off. 2004 SIENNA from Aug. ’04 Prod. (OM45422U)
Page 205 When the alarm sounds frequently (because acceleration or decelera- tion was repeated or sufficient ve- hicle−to−vehicle distance was not maintained), an appropriate vehicle speed cannot be attained and an accident may occur. 2004 SIENNA from Aug. ’04 Prod. (OM45422U)
Page 206 “ON−OFF” button again to turn it on. tempt to accelerate the vehicle to the faster preset speed. 2004 SIENNA from Aug. ’04 Prod. (OM45422U)
Page 207 You can now take your foot light goes off in the instrument panel. In off the accelerator pedal. this case, preset speed data cleared, and you must set the speed from the beginning. 2004 SIENNA from Aug. ’04 Prod. (OM45422U)
Page 208 If you use the using the control lever. Confirm the brake pedal, cruise control is cancelled. setting on the display. 2004 SIENNA from Aug. ’04 Prod. (OM45422U)
Page 209 When the vehicle−to−vehicle distance con- trol mode is activated or the “READY” indicator comes on, the vehicle−to−vehicle distance setting can be changed. The vehicle−to−vehicle distance is always set to LONG when the ignition switch is turned on. 2004 SIENNA from Aug. ’04 Prod. (OM45422U)
Page 210 At become closer to the vehicle ahead of you this time, the display flashes. and the display will flash and beep. 2004 SIENNA from Aug. ’04 Prod. (OM45422U)
Page 211 Do not affix a sticker (including a The accelerator pedal is depressed not be detected. transparent sticker) or attach an ac- or has just been released. cessory around the laser radar sen- sor. 2004 SIENNA from Aug. ’04 Prod. (OM45422U)
Page 212 “E3” appears display, driving, please contact your Toyota dealer. “CRUISE” indicator light in the instrument cluster also flashes. 2004 SIENNA from Aug. ’04 Prod. (OM45422U)
Page 213 Pay special attention to the distance between your vehicle and the vehicle ahead. Always confirm the setting in the display. 2004 SIENNA from Aug. ’04 Prod. (OM45422U)
Page 214 When you release the accelerator pedal, the vehicle will return to the speed set prior to acceleration. 2004 SIENNA from Aug. ’04 Prod. (OM45422U)
Page 215 The slip indicator light blinks and an alarm sounds. (This occurs when the vehicle is about to skid.) If cancelled by a. or b., the preset speed data is cleared and you must set the speed from the beginning. 2004 SIENNA from Aug. ’04 Prod. (OM45422U)
Page 216 If a system malfunction is detected when the conventional cruise control mode is in the ready mode or operating, the master warning light comes on, an alarm sounds and the above code appears. 2004 SIENNA from Aug. ’04 Prod. (OM45422U)
Page 217 ..... . . For vehicle equipped with Navigation system, please refer to the separate “Navigation System Owner’s Manual”. 2004 SIENNA from Aug. ’04 Prod. (OM45422U)
Page 218: Reference
Type 1−1: AM·FM radio/cassette player/ Type 1−2: AM·FM radio/cassette player/ Type 2: AM·FM radio/cassette player/com- compact disc player (with compact disc compact disc player (with compact disc pact disc player with changer changer controller) changer controller) 2004 SIENNA from Aug. ’04 Prod. (OM45422U)
Page 219: Using Your Audio System
If the another function was pre- viously playing, it will come on again. SWITCHING BETWEEN FUNCTIONS Push “AM”, “FM”, “TAPE”, “DISC” “LOAD” if the system is already on but you want to switch from one function to another. 2004 SIENNA from Aug. ’04 Prod. (OM45422U)
Page 220 The player is intended for use with 12 cm (4.7 in.) discs only. 2004 SIENNA from Aug. ’04 Prod. (OM45422U)
Page 221 04 SIENNA_U (L/O 0408) —Controls and features "Type 1−1 Details of specific buttons, controls and features are described in the alphabetical list that follows. 2004 SIENNA from Aug. ’04 Prod. (OM45422U)
Page 222 04 SIENNA_U (L/O 0408) "Type 1−2 Details of specific buttons, controls and features are described in the alphabetical list that follows. 2004 SIENNA from Aug. ’04 Prod. (OM45422U)
Page 223 If a tape rewinds completely, the cassette player will stop and then play that same side. If a tape fast−forwards completely, the cassette will play the other side of the tape using the auto−reverse feature. 2004 SIENNA from Aug. ’04 Prod. (OM45422U)
Page 224 “ERROR 4”: Dolby Laboratories Licensing Corporation. “DOLBY” and the track, or track and disc number currently Toyota dealer to inspect. double D symbol are trademarks of Dolby Laboratories being played. Licensing Corporation. 2004 SIENNA from Aug. ’04 Prod. (OM45422U)
Page 225 Compact disc player random order. To turn off the random fea- There are two repeat features—You can ture, push this button again. either replay a disc track or a whole com- pact disc. 2004 SIENNA from Aug. ’04 Prod. (OM45422U)
Page 226 When the beginning of a tape is reached, The discs in the compact disc changer the player automatically resumes play. can be scanned up only. 2004 SIENNA from Aug. ’04 Prod. (OM45422U)
Page 227 If this button is pushed while a compact disc that does not contain text data is playing, “NO TITLE” will appear on the display. 2004 SIENNA from Aug. ’04 Prod. (OM45422U)
Page 228 04 SIENNA_U (L/O 0408) "Type 2 Details of specific buttons, controls and features are described in the alphabetical list that follows. 2004 SIENNA from Aug. ’04 Prod. (OM45422U)
Page 229 If a tape rewinds completely, the cassette player will stop and then play that same side. If a tape fast−forwards completely, the cassette will play the other side of the tape using the auto−reverse feature. 2004 SIENNA from Aug. ’04 Prod. (OM45422U)
Page 230 If the player malfunctions, your audio sys- want to listen to appears on the display. the front and rear speakers. The display tem will display one of the six following ranges from F7 to R7. error messages. 2004 SIENNA from Aug. ’04 Prod. (OM45422U)
Page 231 If no compact disc is inserted, the shutter display. will close after 15 seconds. PWR·VOL (Power and Volume) Push “PWR·VOL” to turn the audio system on and off. Turn “PWR·VOL” to adjust the volume. 2004 SIENNA from Aug. ’04 Prod. (OM45422U)
Page 232 5 seconds, and then scan again to the next station. To stop To turn the RDS off, push the button until scanning, push this button again. you hear a beep again. 2004 SIENNA from Aug. ’04 Prod. (OM45422U)
Page 233 The discs in the compact disc changer of tion. separate unit can be scanned up only. TAPE Push the “TAPE” button to play a cassette tape. 2004 SIENNA from Aug. ’04 Prod. (OM45422U)
Page 234 The rest of order of most to least recent. the title will appear. 2004 SIENNA from Aug. ’04 Prod. (OM45422U)
Page 235 Each time you push this button, the pro- gram type changes as in the following: ROCK EASY LIS (Easy listening) CLS/JAZZ (Classical music and Jazz) R&B (Rhythm and Blues) INFORM (Information) RELIGION MISC (Miscellaneous) ALERT (Emergency message) 2004 SIENNA from Aug. ’04 Prod. (OM45422U)
Page 236: Audio Remote Controls
Some parts of the audio system can be adjusted using the switches on the steer- ing wheel. Details of the specific switches, controls, and features are described below. 1. Volume control switch 2. “ ” switch 3. “MODE” switch 2004 SIENNA from Aug. ’04 Prod. (OM45422U)
Page 237 Do this again to find tape using the auto−reverse feature. tracks remaining on the current side of the next station. the cassette. 2004 SIENNA from Aug. ’04 Prod. (OM45422U)
Page 238: Rear Seat Audio System
You can enjoy the rear seat audio system with commercial headphone. See “—Head- To turn the audio system on, push the phone input jacks” on page 240 in this “MODE” switch. Section for details. 2004 SIENNA from Aug. ’04 Prod. (OM45422U)
Page 239 Be sure to adjust the volume with this in mind. Make sure the volume is not in- creased, before you turn on the headphone. 2004 SIENNA from Aug. ’04 Prod. (OM45422U)
Page 240 A battery is already set in the control- plode or leak. ler with an insulating sheet, which pre- vents battery from being dis- charged. Before using the controller, remove the insulating sheet. 2004 SIENNA from Aug. ’04 Prod. (OM45422U)
Page 241 To reduce the chance of injury in case of an accident or a sudden stop while driving, stow the controller in the console box or front seat side table when it is not in use. 2004 SIENNA from Aug. ’04 Prod. (OM45422U)
Page 242 Auto−reverse feature: After the cassette player reaches the end of a tape side, it automatically reverses and begins to play the other side. This is true whether the cassette was playing or fast forwarding. 2004 SIENNA from Aug. ’04 Prod. (OM45422U)
Page 243 If you push the button 10 times, the skip feature will be turned off. 2004 SIENNA from Aug. ’04 Prod. (OM45422U)
Page 244 4. “OFF” button receiving an emergency broadcast, a beep Push “OFF” button to turn off the rear sounds and “INVALID” appears on the seat audio system. screen to indicate that no button can be operated. 2004 SIENNA from Aug. ’04 Prod. (OM45422U)
Page 245 Do not replace the battery with wet hands. Water may cause rust. z Do not touch or move any compo- nents inside of the controller, or it may interfere with proper operation. 2004 SIENNA from Aug. ’04 Prod. (OM45422U)
Page 246 16 Ω to 32 Ω. Please contact your Toyota dealer for fur- ther details. CAUTION Adjust the volume when you connect the headphones to the jack. Loud sounds may have a significant impact on the human body. 2004 SIENNA from Aug. ’04 Prod. (OM45422U)
Page 247: Rear Seat Entertainment System
1. Rear seat entertainment system display 2. Headphone input jacks 3. Headphone volume control dials 4. Front audio system 5. Power outlet main switch 6. Power outlets 7. Input terminal adapter 8. Rear seat entertainment system controller 2004 SIENNA from Aug. ’04 Prod. (OM45422U)
Page 248 Make sure the volume is not in- to the input terminal adapter. For details, creased, before you turn on the refer to the manufacturer’s instructions. headphone. 2004 SIENNA from Aug. ’04 Prod. (OM45422U)
Page 249 CAUTION scratched. To reduce the chance of injury in case of an accident or sudden stop while driving, close the display when it is not in use. 2004 SIENNA from Aug. ’04 Prod. (OM45422U)
Page 250 It may cause an accident, fire or electric shock. NOTICE Keep the controller away from direct sunlight, high heat and high humidity. These conditions could cause case to deform or the battery to ex- plode or leak. 2004 SIENNA from Aug. ’04 Prod. (OM45422U)
Page 251 04 SIENNA_U (L/O 0408) 1. Remove the cover of the controller 2. Remove the insulating sheet. as shown. 2004 SIENNA from Aug. ’04 Prod. (OM45422U)
Page 252 To reduce the chance of injury in case of an accident or a sudden stop while driving, stow the controller in the console box or front seat side table when it is not in use. 2004 SIENNA from Aug. ’04 Prod. (OM45422U)
Page 253 This device may not cause harmful sound. interference, and (2) this device must accept any interference received, In- cluding interference that may cause undesired operation. 2004 SIENNA from Aug. ’04 Prod. (OM45422U)
Page 254 7. “""” button This button fast forwards a screen when the DVD player is operated. 8. “RETURN” button This button skips to the predetermined scene for the disc. 2004 SIENNA from Aug. ’04 Prod. (OM45422U)
Page 255 22. “VIDEO” button ated. This button turns on the video mode 15. “SEARCH” button when your personal audio device is This button indicates the title search connected. screen when the DVD player is oper- ated. 2004 SIENNA from Aug. ’04 Prod. (OM45422U)
Page 256 This button also can be used when you lose sight of the controller. 6. Joy stick This joy stick selects a control switch, mode switch on the screen or the menu for the disc. 2004 SIENNA from Aug. ’04 Prod. (OM45422U)
Page 257 CD, a CD text, a dts−CD or a DVD audio Controller disc is not loaded on the front audio sys- tem or the DVD player, only the radio mode can be selected on the rear seat entertainment system. DVD player unit 2004 SIENNA from Aug. ’04 Prod. (OM45422U)
Page 258 To turn off the system, push the “OFF” button. When the front audio system is turned off, the rear audio system and the DVD player will be turned off simultaneously. DVD player unit 2004 SIENNA from Aug. ’04 Prod. (OM45422U)
Page 259 “ENT” button is pushed, the mode display changes to green. If the mode display is gray, it cannot be selected. The “Speaker sound” on the mode display is selected on the front audio system. Radio 2004 SIENNA from Aug. ’04 Prod. (OM45422U)
Page 260 The station frequency will appear on Compact disc mode the screen. “CD” appears on the screen while this mode is selected. The screen shows the track, or track and disc number currently being played. DVD player unit 2004 SIENNA from Aug. ’04 Prod. (OM45422U)
Page 261 Push and hold the “ ” side of the “TUNE/ TRACK” button until “REW” appears on the screen to rewind a tape. Use this button to skip up or down to locate a song or recording. 2004 SIENNA from Aug. ’04 Prod. (OM45422U)
Page 262 Toyota dealer. 1. Remove the cover of the controller as shown. z Dispose of used batteries according to local regulations. 2004 SIENNA from Aug. ’04 Prod. (OM45422U)
Page 263 “DVD ERROR” appears screen: There is a problem inside the player. Eject the disc. Set the disc again. If the malfunction still exists, take your vehicle to your Toyota dealer. 2004 SIENNA from Aug. ’04 Prod. (OM45422U)
Page 264 “DISC” indicator light turns on while the disc is loaded. If the label faces down, the disc cannot be played. In this case, “DISC CHECK” and disc number appear on the screen. 2004 SIENNA from Aug. ’04 Prod. (OM45422U)
Page 265 To select the DVD mode, push the “DVD” button on the controller. You can also select the DVD mode on the mode selection screen mentioned above. EJECTING THE DISC Push the “ ” button. 2004 SIENNA from Aug. ’04 Prod. (OM45422U)
Page 266 4. “AUDIO” button 5. “SUB TITLE” button 6. “ANGLE” button 7. “SET UP” button 8. “SEARCH” button 9. “TOP MENU” button 10. “ ”, “"”, “AA” and “""” buttons DVD player unit 2004 SIENNA from Aug. ’04 Prod. (OM45422U)
Page 267 When the switch is selected by the joy stick, the outline of the switch changes to blue. Push the “ENT” button, and the switch will be highlighted in green. Controller DVD player unit 2004 SIENNA from Aug. ’04 Prod. (OM45422U)
Page 268 04 SIENNA_U (L/O 0408) Top page (DVD video operation switch) Top page (DVD audio operation switch) Top page (video CD) Second page (DVD video operation Second page (DVD audio operation Second page (video CD) switch) switch) 2004 SIENNA from Aug. ’04 Prod. (OM45422U)
Page 269 To change the screen, push the “Top Page” or “Second Page” switch on the screen. On the screen If “ ” appears on the screen when you select a switch, it indicates that the switch cannot work. Controller 2004 SIENNA from Aug. ’04 Prod. (OM45422U)
Page 270 As audio will not play in this case, verify that the video tracks are play- ing and then activate playback. title/chapter number and playback time display may not appear while playing back certain DVD video discs. 2004 SIENNA from Aug. ’04 Prod. (OM45422U)
Page 271 “TOP MENU” driving hazard. Keep this in mind switch on the controller. when you adjust the volume. For the operation of the menu screen, see the separate manual for the DVD disc. 2004 SIENNA from Aug. ’04 Prod. (OM45422U)
Page 272 To turn on the “ ” switch. switch again, push the “ON” switch on the screen. To return to the previous screen, push the “Back” switch on the screen. 2004 SIENNA from Aug. ’04 Prod. (OM45422U)
Page 273 DVD video only— Push the “AA” or “""” switch/button while pausing, the DVD video plays the slow−motion video replay or the slow−mo- tion video replay in reverse. 2004 SIENNA from Aug. ’04 Prod. (OM45422U)
Page 274 You can also display the “SEARCH” button on the controller. screen by pushing the “RETURN” button on the controller. For further details of the predetermined screen, see the separate manual for the DVD disc. 2004 SIENNA from Aug. ’04 Prod. (OM45422U)
Page 275 If you enter the wrong number, push the “Clear” switch to delete the number. Push the “Enter” switch on the screen. The player starts playing the disc from the selected bonus group number. DVD audio 2004 SIENNA from Aug. ’04 Prod. (OM45422U)
Page 276 “SUB TITLE” button on the controller. CHANGING THE STILL PICTURE DVD audio only— Push the “Still Prev.” or “Still Next” switch on the screen to forward or reverse the still pictures. 2004 SIENNA from Aug. ’04 Prod. (OM45422U)
Page 277 To turn off the subtitles, push the “Hide” switch. Push the “Back” switch to return to the previous screen. The selected subtitle language will appear on the screen. 2004 SIENNA from Aug. ’04 Prod. (OM45422U)
Page 278 Push the “Back” switch to return to the previous screen. DVD video— The selected audio language will appear on the screen. DVD audio— The sound condition which is playing at DVD video present will appear on the screen. DVD audio 2004 SIENNA from Aug. ’04 Prod. (OM45422U)
Page 279 The angle number which you can select will appear on the screen. To turn off the screen, push the “Hide” switch. Push the “Back” switch to return to the previous screen. 2004 SIENNA from Aug. ’04 Prod. (OM45422U)
Page 280 When the “Initial Setting” switch on “Setup Menu 2” is pushed, all menus are initial- ized. Setup Menu 1 screen Setup Menu 2 screen 2004 SIENNA from Aug. ’04 Prod. (OM45422U)
Page 281 “Others” switch. The “Enter again. read, push the “Others” switch. The “Enter Audio Lang. Code” screen will appear. Subtitle Lang. Code” screen will appear. To return to the “Select Audio Language” screen, push the “Back” switch. 2004 SIENNA from Aug. ’04 Prod. (OM45422U)
Page 282 To return to the “Select DVD Language” screen, push the “Back” switch on the read, push the “Others” switch. The “Enter screen, push the “Back” switch on the screen. DVD Language Code” screen will appear. screen. 2004 SIENNA from Aug. ’04 Prod. (OM45422U)
Page 283 “Clear” 1” screen. The “Enter Personal Code” switch ten times to initialize the password. screen will appear. To return to the “Setup Menu 1” screen, push the “Back” switch. 2004 SIENNA from Aug. ’04 Prod. (OM45422U)
Page 284 “Setup Menu 2” screen, the “Setup Menu 1” screen. display mode is changed from wide mode 1821 Russian to auto mode. 1115 Korean 0512 Greek 0101 Afar 0102 Abkhazian 0106 Afrikaans 0113 Amharic 0118 Arabic 0119 Assamese 2004 SIENNA from Aug. ’04 Prod. (OM45422U)
Page 285 Inupiak 1311 Macedonian 0515 Esperanto 0914 Indonesian 1312 Malayalam 0520 Estonian 0919 Icelandic 1314 Mongolian 0521 Basque 0923 Hebrew 1315 Moldavian 0601 Persian 1009 Yiddish 1318 Marathi 0609 Finnish 1023 Javanese 1319 Malay 2004 SIENNA from Aug. ’04 Prod. (OM45422U)
Page 286 Telugu 1814 Kirundi 2007 Tajik 1815 Romanian 2008 Thai 1823 Kinyarwanda 2009 Tigrinya 1901 Sanskrit 2011 Turkmen 1904 Sindhi 2012 Tagalog 1907 Sangho 2014 Setswana 1908 Serbo−Croatian 2015 Tonga 1909 Sinhalese 2018 Turkish 2004 SIENNA from Aug. ’04 Prod. (OM45422U)
Page 287 To stop scanning, push this switch again. If the player scanned all the tracks on the disc, it will stop scanning. DVD audio 2004 SIENNA from Aug. ’04 Prod. (OM45422U)
Page 288 “SEARCH” switch on the controller. Push the “Back” switch to return to the menu screen. Move up and down the switches by push- ing the “Shift keys” on the screen. 2004 SIENNA from Aug. ’04 Prod. (OM45422U)
Page 289 Video CD only— Push the “""” switch/button while paus- ing, the DVD video plays the slow−motion video replay. 2004 SIENNA from Aug. ’04 Prod. (OM45422U)
Page 290 You can change the initial setting. (See “CHANGING THE INITIAL SETTING” on page 274 in this Section for details.) After the setting is done, the player plays from the beginning of the chapter or the track. Audio CD 2004 SIENNA from Aug. ’04 Prod. (OM45422U)
Page 291 DVD player Push the “RPT” switch while the track will resume playing. is playing. When the track ends, it will automatically replay. To turn off the re- peat feature, push this switch again. 2004 SIENNA from Aug. ’04 Prod. (OM45422U)
Page 292 The screen may turn purple to deflect the Strengthens Strengthens sunlight. This is not a malfunction. COLOR the red the green color color Strengthens Weakens CONTRAST the contrast the contrast Strengthens Weakens TONE the tone the tone BRIGHTNESS Brightens Darkens 2004 SIENNA from Aug. ’04 Prod. (OM45422U)
Page 293 DVD video disc in this play- er, “REGION CODE ERROR” appears on the screen. Even if the DVD video disc does not have a region code, in some cases you cannot use it. 2004 SIENNA from Aug. ’04 Prod. (OM45422U)
Page 294 Chapter: A unit smaller than a title. A title which this video disc Level 2—7: DVD video discs for children comprises plural chapters. can be played. and G−rated movies can be played. ALL: all countries Number: region code 2004 SIENNA from Aug. ’04 Prod. (OM45422U)
Page 295 Close the input terminal adapter cover when the input terminal adapter is not in use. Inserting a foreign object oth- er than the appropriate plug that fits the adapter may cause electrical fail- ure or short circuit. 2004 SIENNA from Aug. ’04 Prod. (OM45422U)
Page 296 The power supply will restart automatically ing instruments, etc. when you use an appliance that operates within the 115 VAC/100W limits. 2004 SIENNA from Aug. ’04 Prod. (OM45422U)
Page 297 The maximum volume depends on the type of headphones. The recommended headphone impedance is from 16 Ω to 32 Ω. Please contact your Toyota dealer for fur- ther details. 2004 SIENNA from Aug. ’04 Prod. (OM45422U)
Page 298: Car Audio/Video System Operating Hints
2004 SIENNA from Aug. ’04 Prod. (OM45422U)
Page 299 Store cassettes in their cases and out cal motors. This results in static. of direct sunlight. 2004 SIENNA from Aug. ’04 Prod. (OM45422U)
Page 300 Compact disc player Video CDs Use only compact discs marked as shown above. The following products may not be playable on your compact disc player. SACD dts−CD Copy−protected CD CD−R (CD−Recordable) CD−RW (CD−Re−writable) CD−ROM 2004 SIENNA from Aug. ’04 Prod. (OM45422U)
Page 301 The following products may not be playable on your DVD player. SACD Copy−protected CD CD−R (CD−Recordable) CD−RW (CD−Re−writable) CD−ROM DVD−R DVD+R DVD+RW DVD−RW DVD−ROM Special shaped discs Low quality discs DVD−RAM Transparent/translucent discs Labeled discs 2004 SIENNA from Aug. ’04 Prod. (OM45422U)
Page 302 (To see a pin hole, hold the disc up to the light.) Remove discs from the compact disc player when you are not listening to them. Store them in their plastic cases away from moisture, heat, and direct sunlight. 2004 SIENNA from Aug. ’04 Prod. (OM45422U)
Page 303 ........2004 SIENNA from Aug. ’04 Prod. (OM45422U)
Page 304: Front Manual Air Conditioning System Controls
04 SIENNA_U (L/O 0408) Front manual air conditioning system— —Controls 1. “A/C” button 2. Air intake selector 3. Air flow selector 4. Temperature selector 5. Fan speed selector 2004 SIENNA from Aug. ’04 Prod. (OM45422U)
Page 305 For details about air flow selector settings, vents. see “—Air flow selector settings” on page Turning the air flow selector to the 301. floor/windshield position turns on the defogging function with the purpose of clearing the front view. 2004 SIENNA from Aug. ’04 Prod. (OM45422U)
Page 306 2. Fresh—Draws outside air into the sys- tem. To prevent fogging up of the windshield, the air intake mode may change automati- cally to FRESH depending on the condi- tion of the air conditioning system. 2004 SIENNA from Aug. ’04 Prod. (OM45422U)
Page 307: Air Flow Selector Settings
04 SIENNA_U (L/O 0408) —Air flow selector settings —Operating tips To cool off your Toyota after it has been parked in the hot sun, drive with the windows open for a few minutes. This vents the hot air, allowing the air conditioning to cool the interior more quickly.
Page 308 Choose floor/windshield air flow to heat tween the outside and inside tempera- the vehicle interior while defrosting or tures could make the fogging worse. defogging the windshield. 2004 SIENNA from Aug. ’04 Prod. (OM45422U)
Page 309 This is to clean up the front view more quickly. Press the “A/C” button for dehumidified heating. This setting clears the front view more quickly. To heat the vehicle interior while de- frosting windshield, choose floor/windshield air flow. 2004 SIENNA from Aug. ’04 Prod. (OM45422U)
Page 310: Front Automatic Air Conditioning System Controls
5. “MODE” button (air flow selector) 6. Windshield air flow button 7. Temperature selector (“REAR TEMP”) (individual setting on rear passenger side only) 8. Fan speed selector 9. Air intake selector 10. “OFF” button 11. “AUTO” button 2004 SIENNA from Aug. ’04 Prod. (OM45422U)
Page 311 With the “SYNC” button indicator on— tioning system. desire another fan speed mode. This button changes the temperature on the driver side, front passenger side and rear passenger side simultaneously. 2004 SIENNA from Aug. ’04 Prod. (OM45422U)
Page 312 To turn on the air conditioning, press the vents. “A/C” button. The “A/C” button indicator will come on. To turn the air conditioning flows mainly 4. Floor/Windshield—Air off, press the button again. from the floor vents and windshield vents. 2004 SIENNA from Aug. ’04 Prod. (OM45422U)
Page 313: Air Flow Selector Settings
04 SIENNA_U (L/O 0408) —Air flow selector settings —Operating tips To cool off your Toyota after it has been parked in the hot sun, drive with the windows open for a few minutes. This vents the hot air, allowing the air conditioning to cool the interior more quickly.
Page 314 Press the “A/C” button on for dehumidi- fied heating. Choose floor/windshield air flow to heat the vehicle interior while defrosting or defogging the windshield. 2004 SIENNA from Aug. ’04 Prod. (OM45422U)
Page 315: Side Vents
On humid days, do not blow cold air floor/windshield air flow. on the windshield—the difference be- tween the outside and inside tempera- tures could make the fogging worse. 2004 SIENNA from Aug. ’04 Prod. (OM45422U)
Page 316: Rear Manual Air Conditioning System Controls
04 SIENNA_U (L/O 0408) Rear manual air conditioning system— —Controls 1. Fan speed selector (rear) 2. Air flow selectors 3. Temperature selector 4. Fan speed selector (front) 2004 SIENNA from Aug. ’04 Prod. (OM45422U)
Page 317: Air Flow Selector Settings
2. Bi−level—Air flows from both the roof crease. panel vents and floor vent. Temperature selector 3. Floor—Air flows from the floor vent. Turn the knob to adjust the tempera- ture—to the right to warm, to the left to cool. 2004 SIENNA from Aug. ’04 Prod. (OM45422U)
Page 318: Rear Automatic Air Conditioning System Controls
04 SIENNA_U (L/O 0408) Rear automatic air conditioning system— —Controls 1. “AUTO” button 2. Air flow selectors 3. Temperature selector (rear) 4. Fan speed selectors 5. “OFF” button 6. “REAR” button 7. Temperature selector (front) 2004 SIENNA from Aug. ’04 Prod. (OM45422U)
Page 319 To turn on the rear air conditioning system using the front control panel, push the button. To turn it off, push the button again. “OFF” button Push the button to turn off the rear air conditioning system. 2004 SIENNA from Aug. ’04 Prod. (OM45422U)
Page 320: Air Flow Selector Settings
04 SIENNA_U (L/O 0408) —Air flow selector settings 2004 SIENNA from Aug. ’04 Prod. (OM45422U)
Page 321 ..........2004 SIENNA from Aug. ’04 Prod. (OM45422U)
Page 322: Multi−Information Display
04 SIENNA_U (L/O 0408) Multi−information display— 1. “E/M” button 2. Garage door opener buttons 3. “MODE” button 4. Garage door opener indicator 5. Outside temperature and cruise information display 6. Compass 2004 SIENNA from Aug. ’04 Prod. (OM45422U)
Page 323 Instantaneous fuel consumption/ When instrument panel lights Indication Distance to empty temperature Average fuel consumption turned on, the brightness of the display English/U.S. will be reduced. Customary System (E) Metric (M) L/100 km 2004 SIENNA from Aug. ’04 Prod. (OM45422U)
Page 324 The battery side of the hand−held trans- mitter must be pointed away from the HomeLink during the programming pro- cess. For Canadian users, follow the procedure in “Programming an entrance gate/Pro- gramming all devices in the Canadian market”. 2004 SIENNA from Aug. ’04 Prod. (OM45422U)
Page 325 The exact location and color of the and closes. button may vary by brand of garage door opener. Refer the owner’s guide supplied by the garage door opener manufacturer for the location of this “training” button. 2004 SIENNA from Aug. ’04 Prod. (OM45422U)
Page 326 6. Test the operation of the HomeLink pressing the newly programmed button. Check to see if the gate/device oper- ates correctly. 7. Repeat steps 1 through 6 for each re- maining HomeLink button to program another device. 2004 SIENNA from Aug. ’04 Prod. (OM45422U)
Page 327 (signaling the door to stop and re- verse), does not meet current feder- al safety standards. Using a garage door opener without these features increases risk of serious injury or death. 2004 SIENNA from Aug. ’04 Prod. (OM45422U)
Page 328 To reset the calculations, return the mode to “AVG” and push and hold the “MODE” The displayed value is updated every 1 and “E/M” button simultaneously for 2 sec- second. onds. 2004 SIENNA from Aug. ’04 Prod. (OM45422U)
Page 329 The compass works to calibrate the direc- Northeast tion automatically while the vehicle is in East motion, if deviation is small. Southeast For additional precision or for complete South calibrating, “CALIBRATING Southwest COMPASS” below. West Northwest 2004 SIENNA from Aug. ’04 Prod. (OM45422U)
Page 330 To select the zone where the vehicle is currently located, refer to the following map. 2004 SIENNA from Aug. ’04 Prod. (OM45422U)
Page 331 Guam: mode. Saipan: CAUTION Do not adjust the display while the vehicle is moving. Be sure to adjust the display only when the vehicle is stopped. Zone number 2004 SIENNA from Aug. ’04 Prod. (OM45422U)
Page 332 “MODE” and “E/M” buttons simultaneously switch the display to the outside tem- for 10 seconds again. perature. (To switch to this mode, see “—Outside temperature and cruise in- formation display” on page 321.) 2004 SIENNA from Aug. ’04 Prod. (OM45422U)
Page 333: Clock
During calibration, do not operate elec- With manual air conditioning system tric systems (moon roof, power win- dows, etc.) as they may interfere with the calibration. With automatic air conditioning system 2004 SIENNA from Aug. ’04 Prod. (OM45422U)
Page 334: Conversation Mirror
Be sure to adjust When instrument panel lights the mirror only when the vehicle is turned on, the brightness of the time in- stopped. dication will be reduced. To use the mirror, push it down. 2004 SIENNA from Aug. ’04 Prod. (OM45422U)
Page 335: Toyota Park Assist System
“R” position. The mirror angle can be adjusted by push- When the vehicle is forwarding, the ing its edge. front corner sensors work. 1: Rear sensors 2: Rear corner sensors 3: Front corner sensors 2004 SIENNA from Aug. ’04 Prod. (OM45422U)
Page 336 In the following cases, the buzzer will sound several times and the indicator will stay on to indicate that the system is not working properly. When the temperature is extremely low. When any of the sensors are malfunc- tion. 2004 SIENNA from Aug. ’04 Prod. (OM45422U)
Page 337 Distance shown as B in Indicator and mm (in.) buzzer Approximately Intermittent 850—520 (33.5—20.5) Approximately Fast 520—250 (20.5—9.8) intermittent Approximately Continuous 250 (9.8) or less 1: Front sensors 2: Rear corner sensors 3: Rear sensors 2004 SIENNA from Aug. ’04 Prod. (OM45422U)
Page 338 Therefore, always ob- serve the area around the vehicle and do not rely solely on the sys- tem. 2004 SIENNA from Aug. ’04 Prod. (OM45422U)
Page 339 This system works when the ignition key your vehicle. is at the “ON” position and the transmis- sion is in the “R” position. The sensors work only when the transmis- sion is in the “R” position. 2004 SIENNA from Aug. ’04 Prod. (OM45422U)
Page 340 In the following cases, the buzzer will sound several times and the indicator will stay on to indicate that the system is not working properly. When the temperature is extremely low. When any of the sensors are malfunc- tion. 2004 SIENNA from Aug. ’04 Prod. (OM45422U)
Page 341 Rear corner sensors Distance shown as B in Indicator and mm (in.) buzzer Approximately Intermittent 850—520 (33.5—20.5) Approximately Fast 520—250 (20.5—9.8) intermittent Approximately Continuous 250 (9.8) or less 1: Rear corner sensors 2: Rear sensors 2004 SIENNA from Aug. ’04 Prod. (OM45422U)
Page 342 When a radio antenna or fender pole is mounted on your vehicle. When a towing hitch is mounted on your vehicle. 2004 SIENNA from Aug. ’04 Prod. (OM45422U)
Page 343: Rear View Monitor System
Toyota dealer check the system. rors before proceeding. When the bumper is damaged. Do not use the system when the back door is not completely closed. When the indicator is continuously on. 2004 SIENNA from Aug. ’04 Prod. (OM45422U)
Page 344 When backing up, be sure to check behind and all around the vehicle visually and with mirror be- fore proceeding. Corners of bumper 2004 SIENNA from Aug. ’04 Prod. (OM45422U)
Page 345 In the following cases, it may become difficult to see the images on the screen, even when the system is functioning. In the dark (for example, at night) When the temperature near the lens is high or low 2004 SIENNA from Aug. ’04 Prod. (OM45422U)
Page 346: Power Outlets
Rear 2004 SIENNA from Aug. ’04 Prod. (OM45422U)
Page 347 Push the main switch once again to turn the power outlet off. When the power out- let is not in use, make sure that the main switch is turned off. Beside third seat 2004 SIENNA from Aug. ’04 Prod. (OM45422U)
Page 348: Glove Box
Measuring devices which process pre- closed while driving. cise data: medical equipment, measur- ing instruments, etc. Other appliances requiring an extremely stable power supply: microcomputer− controlled electric blankets, touch sen- sor lamps, etc. 2004 SIENNA from Aug. ’04 Prod. (OM45422U)
Page 349: Garage Door Opener Box
Velcro. Open the cover and remove the Velcro ter. loop. 2004 SIENNA from Aug. ’04 Prod. (OM45422U)
Page 350 Close the cover. the cover. 2004 SIENNA from Aug. ’04 Prod. (OM45422U)
Page 351: Auxiliary Boxes
If the transmitter is clattering during driv- ing, fill in a piece of felt or pad to prevent the transmitter from clattering. 2004 SIENNA from Aug. ’04 Prod. (OM45422U)
Page 352 250 g (0.55 lb.) in Type A (driver’s side roof) Position 1 Position 2 Type B (instrument panel) Type C (instrument panel, without seat heater) 2004 SIENNA from Aug. ’04 Prod. (OM45422U)
Page 353 Type D (instrument panel, with seat heat- Type F (front door) Type H (spare tire cover) Type G (quarter trim) Type I (front seat side table) Type E (upper side of the glove box) 2004 SIENNA from Aug. ’04 Prod. (OM45422U)
Page 354: Coin Holder
To reduce the chance of injury in case of an accident or a sudden stop while driving, keep the coin holder closed when it is not in use. Type K (front passenger’s seat) 2004 SIENNA from Aug. ’04 Prod. (OM45422U)
Page 355: Cup Holders
Type B (quarter trim) Type D (rear side of the front seat side table) 2004 SIENNA from Aug. ’04 Prod. (OM45422U)
Page 356 04 SIENNA_U (L/O 0408) Type E (front side of console box) Type G (console box tray) Type F (rear side of console box) 2004 SIENNA from Aug. ’04 Prod. (OM45422U)
Page 357: Bottle Holders
This box is designed to place things like bottles. Do not put a cup or open bottle in the bottle holder because the con- tents may spill when the door opens or closes. Sliding door 2004 SIENNA from Aug. ’04 Prod. (OM45422U)
Page 358: Removable Console Box
CAUTION To reduce the chance of injury in case of an accident or a sudden stop, always keep the console box closed while driving. 2004 SIENNA from Aug. ’04 Prod. (OM45422U)
Page 359 Open the auxiliary box of the rear side and pull up the lock release lever to disengage the rear lock. Then lift the console box and release the front hook. Between the second seats 2004 SIENNA from Aug. ’04 Prod. (OM45422U)
Page 360 Make sure the console box is se- curely locked by pushing forward, rearward, upward sideways. Failure to do so may cause an un- expected accident or severe injury in the event of emergency braking or a collision. 2004 SIENNA from Aug. ’04 Prod. (OM45422U)
Page 361 Make sure the console box is se- curely locked by pushing forward and rearward. Failure to do so may cause an unexpected accident or severe injury in the event of emer- gency braking or a collision. 2004 SIENNA from Aug. ’04 Prod. (OM45422U)
Page 362: Note Pad Holder
Make sure the cup holder and small tray are locked securely. 2004 SIENNA from Aug. ’04 Prod. (OM45422U)
Page 363: Front Seat Side Table
2004 SIENNA from Aug. ’04 Prod. (OM45422U)
Page 364: Coat Hooks
If the curtain shield airbag inflates, those items will be hurled away with great force or the curtain shield airbag may not activate cor- rectly. When you hang clothes, hang them on the coat hook directly. 2004 SIENNA from Aug. ’04 Prod. (OM45422U)
Page 365: Grocery Bag Hooks
4 kg (8.8 lb.) in z Type D—To prevent damage to the hook, avoid hanging heavy loads on Type B (front seats) Type D (under the back door) 2004 SIENNA from Aug. ’04 Prod. (OM45422U)
Page 366: Cargo Net Hooks
NOTICE To prevent damage to the hook, avoid hanging things other than a cargo net on it. Pattern 1 Pattern 3 Pattern 2 Pattern 4 2004 SIENNA from Aug. ’04 Prod. (OM45422U)
Page 367: Tie−Down Hooks
3. After adjusting, be sure to tighten the rectly. cross rails by turning knobs clockwise. Follow the manufacturer’s instructions and precautions when installing the attach- ments or their equivalent. 2004 SIENNA from Aug. ’04 Prod. (OM45422U)
Page 368: Sun Shade
NOTICE z Do place anything When loading the luggages, be careful shade. not to scratch the surface of the Rear window moon roof. Quarter window 2004 SIENNA from Aug. ’04 Prod. (OM45422U)
Page 369: Floor Mat
If the floor ing clips into the holes in the floor carpet. slips and interferes with movement of the pedals during driv- ing, it may cause an accident. 2004 SIENNA from Aug. ’04 Prod. (OM45422U)
Page 370 04 SIENNA_U (L/O 0408) 2004 SIENNA from Aug. ’04 Prod. (OM45422U)
Page 371 ..........2004 SIENNA from Aug. ’04 Prod. (OM45422U)
Page 372: Break−In Period
Also, light knocking for a short time while accel- this can increase maintenance costs. erating or driving up hills. This is normal and there is no need for concern. 2004 SIENNA from Aug. ’04 Prod. (OM45422U)
Page 373 If you use gasohol in your els. In the U.S., category 4 has been Toyota, be sure that it has an octane adopted. The WWFC improves air quali- rating no lower than 87. ty by providing for better emissions in...
Page 374: Fuel Pump Shut Off System
Operation in foreign countries The fuel pump shut off system stops sup- GASOLINE QUALITY If you plan to drive your Toyota in plying fuel to the engine to minimize the another country... In a very few cases, you may experience...
Page 375: Three−Way Catalytic Converter
The exhaust gas is very hot. Do not drive, idle or park your ve- hicle over anything that might burn easily such as grass, leaves, paper or rags. 2004 SIENNA from Aug. ’04 Prod. (OM45422U)
Page 376: Engine Exhaust Cautions
High tem- vehicle. perature exhaust gases also burn the oil used to lubricate the exhaust valve stems. 2004 SIENNA from Aug. ’04 Prod. (OM45422U)
Page 377: Iridium−Tipped Spark Plugs
2004 SIENNA from Aug. ’04 Prod. (OM45422U)
Page 378: Brake System
This means that the anti−lock brake system is in the self−check mode, and does not indicate a malfunction. 2004 SIENNA from Aug. ’04 Prod. (OM45422U)
Page 379 Compared with vehicles without an anti−lock brake system, your vehicle may require a longer stopping dis- tance in the following cases: 2004 SIENNA from Aug. ’04 Prod. (OM45422U)
Page 380 Toyota dealer. slippery road surfaces. In this case, not only the anti−lock brake system will fail but also the vehicle will become extremely unsta- ble during braking. Type B 2004 SIENNA from Aug. ’04 Prod. (OM45422U)
Page 381 “Service reminder indicators In this case, not only the anti−lock and warning buzzers” on page 167 in Sec- brake system will fail but also the tion 1−5. vehicle will become extremely unsta- ble during braking. 2004 SIENNA from Aug. ’04 Prod. (OM45422U)
Page 382: Brake Pad Wear Limit Indicators
This is the primary identification number checked and replaced by your Toyota for your Toyota. It is used in registering dealer as soon as possible. Expensive ro- the ownership of your vehicle. tor damage can result if the pads are not replaced when necessary.
Page 383: Theft Prevention Labels
NOTICE The engine number is stamped on the You should not attempt to remove the engine block as shown. theft prevention labels as it may vio- late certain state or federal laws. 2004 SIENNA from Aug. ’04 Prod. (OM45422U)
Page 384: Tire Information
“Checking and replacing tires” on page 466. 5. Tire ply composition and mate- rials—Plies mean a layer of rub- ber−coated parallel cords. Cords mean the strands forming the plies in the tire. 2004 SIENNA from Aug. ’04 Prod. (OM45422U)
Page 385 9. Load limit at maximum cold tire inflation pressure—For details, see “Checking and replacing tires” on page 466. 2004 SIENNA from Aug. ’04 Prod. (OM45422U)
Page 386 4. The location of the tread wear details, indicators—For “Checking and replacing tires” on page 466. 5. Load limit at maximum cold tire inflation pressure—For details, see “Checking and replacing tires” on page 466. 2004 SIENNA from Aug. ’04 Prod. (OM45422U)
Page 387 “RADIAL” on the 4. Tire size code sidewall. A tire not marked with 5. Manufacturer’s optional tire type “RADIAL” is a bias−ply tire. code 6. Manufacturing week 7. Manufacturing year 2004 SIENNA from Aug. ’04 Prod. (OM45422U)
Page 388 4. Tire construction code (R=Radial, 8. Carcass D=Diagonal) 9. Rim lines 5. Wheel diameter (in inches) 10.Bead wires 6. Load index (2 digits or 3 digits) 11. Chafer 7. Speed symbol (alphabet with one letter) 2004 SIENNA from Aug. ’04 Prod. (OM45422U)
Page 389 Safety Requirements in addi- tion to these grades. Quality grades can be found where appli- cable on the tire sidewall between tread shoulder and maximum sec- tion width. For example: Treadwear 200 Traction AA Temperature A 2004 SIENNA from Aug. ’04 Prod. (OM45422U)
Page 390 Excessive speed, underinfla- tion, or excessive loading, either sep- arately or in combination, can cause heat buildup and possible tire failure. 2004 SIENNA from Aug. ’04 Prod. (OM45422U)
Page 391 Maximum inflation pressure is shown on the sidewall of the tire the sum of— (a) curb weight; Maximum loaded vehicle weight (b) accessory weight; (c) vehicle capacity weight; and (d) production options weight 2004 SIENNA from Aug. ’04 Prod. (OM45422U)
Page 392 Vehicle maximum load on the tire its share of the maximum loaded vehicle weight and dividing by two 2004 SIENNA from Aug. ’04 Prod. (OM45422U)
Page 393 Designated seating capacity, Vehicle normal load, number of Occupant distribution in a normally number of occupants occupants loaded vehicle 2 through 4 2 in front 5 through 10 2 in front, 1 in second seat 2004 SIENNA from Aug. ’04 Prod. (OM45422U)
Page 394: Vehicle Load Limits
(weight) the weight of each person, the seat- and the number of occupants. For de- ing capacity given may exceed the tails, see “Capacity and distribution” total load capacity. that follows. 2004 SIENNA from Aug. ’04 Prod. (OM45422U)
Page 395: Cargo And Luggage
150 lb. as close to the floor as pos- passengers in your vehicle, the sible. amount of available cargo and lug- gage load capacity is 650 lbs. (1400–750 (5x150)=650 lbs). 2004 SIENNA from Aug. ’04 Prod. (OM45422U)
Page 396 (1160 lb. – 366 lb. = 794 lb.) From this condition, if 3 more passen- gers with the combined weight of 176 kg (388 lb.) get on, the available car- go and luggage load will be reduced as follows: 2004 SIENNA from Aug. ’04 Prod. (OM45422U)
Page 397 (Cargo capacity) = (Total load capac- ity) − (Total weight of occupants) + (Weight of the removed second seats) 2004 SIENNA from Aug. ’04 Prod. (OM45422U)
Page 398: Types Of Tires
D Do not use tires other than the conditions, as well as for use all year manufacturer’s designated round. tires, and never mix tires or wheels of the sizes different from the originally equipped tires and wheels. 2004 SIENNA from Aug. ’04 Prod. (OM45422U)
Page 399 ..........How to save fuel and make your vehicle last longer ... . . 2004 SIENNA from Aug. ’04 Prod. (OM45422U)
Page 400: Before Starting The Engine
If the engine stalls... Simply restart it, using the correct proce- dure given in normal starting. If the engine will not start... See “If your vehicle will not start” on page 406 in Section 4. 2004 SIENNA from Aug. ’04 Prod. (OM45422U)
Page 401: Tips For Driving In Various Conditions
If they still do not work safely, pull to the side of the road and call a Toyota dealer for assistance. 2004 SIENNA from Aug. ’04 Prod. (OM45422U)
Page 402: All−Wheel Driving Tips
Do not use tires (including snow tires) different brands, sizes, construction or tread patterns. (See “Checking and replacing tires” on page 466 and “Installing snow tires and chains” on page 471 in Section 7−2.) 2004 SIENNA from Aug. ’04 Prod. (OM45422U)
Page 403: Winter Driving Tips
When it is extremely cold, we recommend Depending on where you are driving, This product is available at your Toyota to use 60% solution for your Toyota, to we recommend you carry some emer- dealer and most auto parts stores. Follow provide protection down to about −50_C...
Page 404: Dinghy Towing
With towing package junk yard, etc. 3946 kg (8700 lb.) All−wheel drive models Without towing package 3311 kg (7300 lb.) With towing package 3992 kg (8800 lb.) 2004 SIENNA from Aug. ’04 Prod. (OM45422U)
Page 405 The load on either the front or rear axle resulting from distribution of the gross vehicle weight on both axles must not exceed the Gross Axle Weight Rating (GAWR) listed on the Certification Label. 2004 SIENNA from Aug. ’04 Prod. (OM45422U)
Page 406 The hitch ball and king pin should have a light coat of grease. 2004 SIENNA from Aug. ’04 Prod. (OM45422U)
Page 407 Have someone guide you when tial, wheel bearing, etc.) for the first for towing purpose. backing to reduce the risk of an acci- 800 km (500 miles) of driving. dent. 2004 SIENNA from Aug. ’04 Prod. (OM45422U)
Page 408 3. When the wheel blocks are in place, radius with your vehicle. release your brakes slowly until the blocks absorb the load. 4. Apply the parking brake firmly. 5. Shift into “P” and turn off the engine. 2004 SIENNA from Aug. ’04 Prod. (OM45422U)
Page 409: How To Save Fuel And Make Your Vehicle Last Longer
Driving with the selector lever in “4” will reduce the fuel economy. (For de- tails, see “Automatic transmission” on page 179 in Section 1−6.) Accelerate slowly smoothly. Avoid jackrabbit starts. Get into high gear as quickly as possible. 2004 SIENNA from Aug. ’04 Prod. (OM45422U)
Page 410 Supplement”.) Maintain a moderate speed on high- ways. The faster you drive, the greater the fuel consumption. By reducing your speed, you will cut down on fuel con- sumption. 2004 SIENNA from Aug. ’04 Prod. (OM45422U)
Page 411: In Case Of An Emergency
..If you cannot operate back door opener ..... . . 2004 SIENNA from Aug. ’04 Prod. (OM45422U)
Page 412: If Your Vehicle Will Not Start
Have with your foot off the accelerator pedal. checked at your Toyota dealer. If none of If the engine turns over at its normal If the engine does not start after 15 se- your keys work, there may be a malfunc- speed but will not start—...
Page 413 2000 rpm with the accelerator pedal the affected area with water imme- lightly depressed. diately. Then get immediate medical attention. If possible, continue to apply water with a sponge or cloth while en route to the medical office. 2004 SIENNA from Aug. ’04 Prod. (OM45422U)
Page 414 2004 SIENNA from Aug. ’04 Prod. (OM45422U)
Page 415: If Your Engine Stalls While Driving
“LOCK”, and try starting the engine vehicle at low speeds. Have your vehicle 7. Carefully dispose of the battery cover again. checked by your Toyota dealer as soon as cloths—they may now contain sulfuric If the engine will not start, see “If your possible.
Page 416: If Your Vehicle Overheats
Escaping steam or coolant is hot. Serious injury could result from a sign of very high pressure. scalding hot fluid and steam blown out under pressure. 2004 SIENNA from Aug. ’04 Prod. (OM45422U)
Page 417: If You Have A Flat Tire
When the tire goes flat or when the tire pressure is below 100 kPa (1.0 kgf/cm or bar, 15 psi), the tire must be replaced. If you are not sure, consult your Toyota dealer. Do not use the repaired tire. 2004 SIENNA from Aug. ’04 Prod. (OM45422U)
Page 418 If caught, resulting in damage. the vehicle tires deteriorate, you could lose control of the steering wheel or the brakes, causing death or serious inju- 2004 SIENNA from Aug. ’04 Prod. (OM45422U)
Page 419 420 kPa (4.2 economy and permits easier installa- kgf/cm or bar, 60 psi). tion in case of a flat tire. D Do not exceed 80 km/h (50 mph) when driving with the compact spare tire. 2004 SIENNA from Aug. ’04 Prod. (OM45422U)
Page 420 1. Wheel nut wrench 2. Jack handle 3. Jack 4. Spare tire To prepare yourself for an emergency, you should familiarize yourself with the use of the jack, each of the tools and their storage locations. 2004 SIENNA from Aug. ’04 Prod. (OM45422U)
Page 421 Open the right side sliding door and you will find the flap on the floor. Pull back the flap to find the spare tire clamp bolt. 2004 SIENNA from Aug. ’04 Prod. (OM45422U)
Page 422 Do not store the flat spare As the tire carrier is designed for the tire with the tire carrier so it compact spare tire, the standard tire may not be held securely. cannot be stored there. 2004 SIENNA from Aug. ’04 Prod. (OM45422U)
Page 423 1. Wheel nut wrench 2. Jack handle 3. Jack 4. Spare tire To prepare yourself for an emergency, you should familiarize yourself with the use of the jack, each of the tools and their storage locations. 2004 SIENNA from Aug. ’04 Prod. (OM45422U)
Page 424 3. Remove the spare tire cover. ward during a collision or sudden sure the wrench is securely held. 4. Loosen the bolt, then remove the stop. bolt and spacer. Then take the spare tire out of the vehicle. 2004 SIENNA from Aug. ’04 Prod. (OM45422U)
Page 425 CAUTION wheels or behind one of the rear wheels. Do not try to pull off the orna- ment by hand. Take due care in handling the ornament to avoid unexpected personal injury. 2004 SIENNA from Aug. ’04 Prod. (OM45422U)
Page 426 Be careful that the wrench does not slip off the nut. Do not remove the nuts yet—just un- screw them about one−half turn. 2004 SIENNA from Aug. ’04 Prod. (OM45422U)
Page 427 D When raising the vehicle, do not place any objects on top of or underneath the jack. D Raise the vehicle only high enough to remove and change the tire. 2004 SIENNA from Aug. ’04 Prod. (OM45422U)
Page 428 Wiggle the tire and press it and turn it clockwise. As the jack back over the other bolts. touches the vehicle and begins to lift, double−check that it is properly posi- tioned. 2004 SIENNA from Aug. ’04 Prod. (OM45422U)
Page 429 Press back on the cause wheel nuts to loosen and tire and see if you can tighten them eventually cause a wheel to come off more. while driving. 2004 SIENNA from Aug. ’04 Prod. (OM45422U)
Page 430 Tighten each nut a little at a time in the order shown. Repeat the process until all the nuts are tight. 2004 SIENNA from Aug. ’04 Prod. (OM45422U)
Page 431 491 in Sec- tion 8 with a torque wrench. Have a technician repair the flat tire and re- place the spare tire with it. 2004 SIENNA from Aug. ’04 Prod. (OM45422U)
Page 432: If Your Vehicle Becomes Stuck
During the rocking operation the vehicle may suddenly move forward or backward as it becomes unstuck, causing injury or damage to nearby people or ob- jects. 2004 SIENNA from Aug. ’04 Prod. (OM45422U)
Page 433: If Your Vehicle Needs To Be Towed
If towing is necessary, we recommend (a) Towing with wheel lift type truck— (a) Towing with wheel lift type truck— you to have it done by your Toyota —From front —From front dealer or a commercial tow truck ser- vice.
Page 434 Do not tow with sling type truck, ei- ther from the front or rear. This may cause body damage. From rear— Use a towing dolly under the front wheels. 2004 SIENNA from Aug. ’04 Prod. (OM45422U)
Page 435: If You Lose Your Keys
Toyota dealer as soon as Even if you lose only one key, contact possible to avoid the possibility of theft or your Toyota dealer to make a new key. If an accident. Then, have the identification you lose all your master keys, you cannot number of your new transmitter registered.
Page 436: If You Cannot Operate Back Door Opener
5. Insert the cover. 6. Start the engine. For your safety, keep the brake pedal depressed. Be sure to have the system checked by your Toyota dealer as soon as possible. With power back door system 2004 SIENNA from Aug. ’04 Prod. (OM45422U)
Page 437 04 SIENNA_U (L/O 0408) 2. Pull the lever with the back door motor, open the back door. Be sure to have the back door opener checked/repaired by your Toyota dealer. 2004 SIENNA from Aug. ’04 Prod. (OM45422U)
Page 438 04 SIENNA_U (L/O 0408) 2004 SIENNA from Aug. ’04 Prod. (OM45422U)
Page 439: Corrosion Prevention And Appearance Care
........2004 SIENNA from Aug. ’04 Prod. (OM45422U)
Page 440 Now, it is up to be dry. to see all the mud and dirt. It will do you. Proper care of your Toyota can help more harm than good to simply wet the High ambient temperatures can cause ensure long−term corrosion prevention.
Page 441 It may fly off damp as to cause corrosion. Even if your the wheel and cause accidents while garage is heated, a wet vehicle can cor- the vehicle is moving. rode if the ventilation is poor. 2004 SIENNA from Aug. ’04 Prod. (OM45422U)
Page 442 NOTICE the paint. If a nozzle becomes blocked, do not try to clear it with a pin or other object. The nozzle will be damaged. 2004 SIENNA from Aug. ’04 Prod. (OM45422U)
Page 443 (or mat) and NOTICE cause a malfunction; and it may Do not use solvent, thinner, gasoline cause body corrosion. or window cleaner on the interior. 2004 SIENNA from Aug. ’04 Prod. (OM45422U)
Page 444 If you use cleaners or polishing belts—it may weaken them. agents, make sure their ingredients do not include the substances men- z Do not use the belts until they be- tioned above. come dry. 2004 SIENNA from Aug. ’04 Prod. (OM45422U)
Page 445 Try to keep your upholstery always clean. z Long exposure to direct sunlight may cause the leather surface to harden and shrink. Keep your ve- hicle in a shaded area, especially in the summer. 2004 SIENNA from Aug. ’04 Prod. (OM45422U)
Page 446 04 SIENNA_U (L/O 0408) 2004 SIENNA from Aug. ’04 Prod. (OM45422U)
Page 447 ......Emissions Inspection and Maintenance (I/M) programs ..For scheduled maintenance information, please refer to the “Sched- uled Maintenance Guide” or “Owner’s Manual Supplement”. 2004 SIENNA from Aug. ’04 Prod. (OM45422U)
Page 448: Maintenance Requirements
Simple instructions for how to per- tablishment or individual without invali- or if you prefer, your Toyota dealer will be form them are presented on page 447 in dating this warranty. See “Owner’s War- pleased to do them at a nominal cost.
Page 449: General Maintenance
Toyota dealer or a quali- Radiator, condenser and hoses fied service shop immediately. It is recom- Check that the front of the radiator and...
Page 450 Steering wheel not pull to one side when applied. ing when the primary latch is released. Be alert for changes in steering condition, such as hard steering or strange noise. 2004 SIENNA from Aug. ’04 Prod. (OM45422U)
Page 451: Does Your Vehicle Need Repairing
Tire inflation pressure Check the pressure with a gauge ev- mance, sounds, and visual tip−offs that vehicle to your Toyota dealer as soon as indicate service is needed. Some impor- possible. It probably needs adjustment or ery two weeks, or at least once a tant clues are as follows: repair.
Page 452: Emissions Inspection And Maintenance (I/M) Programs
Also, if the malfunction indicator lamp had come on recently due to temporary mal- function such as a loose fuel tank cap, your vehicle may not pass the I/M test. 2004 SIENNA from Aug. ’04 Prod. (OM45422U)
Page 453 ..........2004 SIENNA from Aug. ’04 Prod. (OM45422U)
Page 454: Engine Compartment Overview
3. Engine oil level dipstick 4. Engine coolant reservoir 5. Engine oil filler cap 6. Brake fluid reservoir 7. Fuse block 8. Battery 9. Electric cooling fans 10. Condenser 11. Radiator 2004 SIENNA from Aug. ’04 Prod. (OM45422U)
Page 455: Fuse Locations
04 SIENNA_U (L/O 0408) Fuse locations Spare fuses Spare fuses 2004 SIENNA from Aug. ’04 Prod. (OM45422U)
Page 456: Do−It−Yourself Service Precautions
Do not dispose of used oil and fil- ways use automotive jack stands or ter in household trash, in sewers or other solid supports. onto the ground. Call your dealer or a service station for information concerning recycling or disposal. 2004 SIENNA from Aug. ’04 Prod. (OM45422U)
Page 457: Positioning The Jack
Use only spark plugs of the speci- fied type. Using other types will cause engine damage, loss of per- formance or radio noise. Rear (two−wheel drive models) 2004 SIENNA from Aug. ’04 Prod. (OM45422U)
Page 458 Never get under the vehicle when the vehicle is supported by the jack alone; use vehicle support stands. 2004 SIENNA from Aug. ’04 Prod. (OM45422U)
Page 459: Parts And Tools
Baking soda Screwdriver See page 458 in Section 7−2 for de- Grease tails about coolant type selection. Wrench Conventional wrench (for terminal Demineralized or distilled water clamp bolts) Tools: Funnel (only for adding coolant) 2004 SIENNA from Aug. ’04 Prod. (OM45422U)
Page 460 04 SIENNA_U (L/O 0408) 2004 SIENNA from Aug. ’04 Prod. (OM45422U)
Page 461 Aluminum wheel precautions ....... . 2004 SIENNA from Aug. ’04 Prod. (OM45422U)
Page 462: Checking The Engine Oil Level
3. Reinsert the dipstick—push it in as far 1.5 (1.6, 1.3) as it will go, or the reading will not be correct. 4. Pull the dipstick out and look at the oil level while holding a rag under the end. 2004 SIENNA from Aug. ’04 Prod. (OM45422U)
Page 463 API grade SL “Energy−Conserving” or ILSAC multigrade engine oil Recommended viscosity: SAE 5W−30 API service symbol Outside temperature SAE 5W−30 is the best choice for good fuel economy and good starting in cold weather. ILSAC certification mark 2004 SIENNA from Aug. ’04 Prod. (OM45422U)
Page 464: Checking The Engine Coolant Level
Oil”. radiator cap and drain cock and water pump. If you can find no leak, have your Toyota dealer test the cap pressure and check for leaks in the cooling system. 2004 SIENNA from Aug. ’04 Prod. (OM45422U)
Page 465 Further supplemental inhibitors or additives use in Toyota vehicles. are neither needed nor recommended. Please contact your Toyota dealer for fur- ther details about “Toyota Genuine Long Life Coolant”. 2004 SIENNA from Aug. ’04 Prod. (OM45422U)
Page 466: Checking The Radiator And Condenser
To maintain the air conditioning efficiency, dirty or you are not sure of their condi- inspect and replace the air conditioning tion, take your vehicle to a Toyota dealer. filter according to the maintenance sched- ule. In dusty areas or areas with heavy...
Page 467 1. Open the glove box, and slide off 2. Push in each side of the glove box 3. Remove the filter case from the filter the damper as shown. to disconnect the claws. outlet as shown in the illustration. 2004 SIENNA from Aug. ’04 Prod. (OM45422U)
Page 468: Checking Brake Fluid
NOTICE tioning performance. If you spill some of the fluid, be sure to wash it off with water to prevent it from damaging the parts or paint. 2004 SIENNA from Aug. ’04 Prod. (OM45422U)
Page 469: Checking Power Steering Fluid
(about room temperature, NOTICE 10_C—30_C or 50_F—85_F) if the engine Avoid overfilling, or the power steer- has not been run for about five hours. ing could be damaged. Type A 2004 SIENNA from Aug. ’04 Prod. (OM45422U)
Page 470 The smaller tire size can gain pressure very quickly. Add com- pressed air in small quantities and check the pressure often until it reaches the specified pressure. Type B 2004 SIENNA from Aug. ’04 Prod. (OM45422U)
Page 471 If a tire frequently needs refilling, valve. In case of applying too have it checked by your Toyota deal- much air, press the center of the valve and release the air to adjust. 2004 SIENNA from Aug. ’04 Prod. (OM45422U)
Page 472: Checking And Replacing Tires
D Wheel deformation and/or tire ∆ shown by the “TWI” or “ ” marks, separation etc., molded on the sidewall of D A greater possibility of tire each tire. damage from road hazards 2004 SIENNA from Aug. ’04 Prod. (OM45422U)
Page 473 CAUTION should be replaced. If you are not sure, consult with your Toyota dealer. Observe the following instruc- tions. Otherwise, an accident may occur resulting in death or serious injuries. 2004 SIENNA from Aug. ’04 Prod. (OM45422U)
Page 474: Rotating Tires
See “If you have a flat tire” on page 411 in Section 4 for tire change proce- dure. 2004 SIENNA from Aug. ’04 Prod. (OM45422U)
Page 475: Run−Flat Tires
When the tire goes flat or when the tire pressure is below 100 kPa (1.0 kgf/cm or bar, 15 psi), the tire must be replaced. If you are not sure, consult your Toyota dealer. Do not use the repaired tire. 2004 SIENNA from Aug. ’04 Prod. (OM45422U)
Page 476 Do not drive for longer than For details about the tire pressure 160 km (100 miles) or over 90 warning system, see “Tire pressure km/h (55 mph). warning system” on page 188 in Sec- tion 1−6. 2004 SIENNA from Aug. ’04 Prod. (OM45422U)
Page 477: Installing Snow Tires And Chains
Also, do not attempt to go through automatic wash as the vehicle may get caught, resulting in damage. 2004 SIENNA from Aug. ’04 Prod. (OM45422U)
Page 478 When the tires must be re- sult in damage to the vehicle as well placed or repaired, consult your as the tire. Toyota dealer authorized tire dealer. 2004 SIENNA from Aug. ’04 Prod. (OM45422U)
Page 479: Replacing Wheels
2004 SIENNA from Aug. ’04 Prod. (OM45422U)
Page 480: Aluminum Wheel Precautions
When balancing your wheels, use only Toyota balance weights or equivalent and a plastic or rubber hammer. As with any wheel, periodically check your aluminum wheels for damage. If damaged, replace immediately. 2004 SIENNA from Aug. ’04 Prod. (OM45422U)
Page 481 ........2004 SIENNA from Aug. ’04 Prod. (OM45422U)
Page 482: Checking Battery Condition
If possible, con- enough to keep the battery firmly in tinue to apply water with a sponge place. Overtightening may damage the or cloth while en route to the medi- battery case. cal office. 2004 SIENNA from Aug. ’04 Prod. (OM45422U)
Page 483: Battery Recharging Precautions
Never recharge the battery while the Clear or Have battery tric moon roof” on page 53 in Section engine is running. Also, be sure all light checked by your 1−2. accessories are turned off. yellow Toyota dealer. 2004 SIENNA from Aug. ’04 Prod. (OM45422U)
Page 484: Checking And Replacing Fuses
492 in Section 8 of this manual for the functions controlled by each circuit. Type C and D—When any of the fuses Type B Type D are blown, contact your Toyota dealer. 2004 SIENNA from Aug. ’04 Prod. (OM45422U)
Page 485: Adding Washer Fluid
Have your Toyota dealer correct it as light comes on, the washer tank may be soon as possible. empty. Add washer fluid.
Page 486: Replacing Light Bulbs
Do not touch the high voltage sock- pooled inside light, contact your et when the headlight turns on. Toyota dealer. 20000 V is momentarily generated and may cause severe injury by electric shock. 2004 SIENNA from Aug. ’04 Prod. (OM45422U)
Page 487 Stop/tail and rear side marker lights — 21/5 Tail lights — Back−up lights License plate lights — Front personal lights — Rear personal lights — Luggage compartment light — Vanity lights — Door courtesy lights — 2004 SIENNA from Aug. ’04 Prod. (OM45422U)
Page 488 If the connector is tight, wiggle it. Aiming is not necessary after replacing the bulb. When aiming adjustment is nec- essary, contact your Toyota dealer. 2004 SIENNA from Aug. ’04 Prod. (OM45422U)
Page 489 If either the left or right front fog light bulbs burns out, contact your Toyota dealer. NOTICE Do not try to replace the front fog light bulbs by yourself. You may dam- age the vehicle. 2004 SIENNA from Aug. ’04 Prod. (OM45422U)
Page 490 Remove the bolts. a: Rear turn signal light Remove the strap with a Phillips−head b: Stop/tail and rear side marker light screwdriver. Pull and hold the tab and remove the bulb unit. 2004 SIENNA from Aug. ’04 Prod. (OM45422U)
Page 491 When installing the back door trim, be careful not to jam any wire har- ness and connector. Otherwise, they may be damaged. Remove the strap with a Phillips−head screwdriver. a: Tail light b: Back−up light 2004 SIENNA from Aug. ’04 Prod. (OM45422U)
Page 492 04 SIENNA_U (L/O 0408) NOTICE When installing the back door trim, be careful not to jam any wire har- ness and connector. Otherwise, they may be damaged. 2004 SIENNA from Aug. ’04 Prod. (OM45422U)
Page 493 ........... . . 2004 SIENNA from Aug. ’04 Prod. (OM45422U)
Page 494: Dimensions And Weights
Vehicle without towing package 907 (2000) (trailer weight + cargo weight) kg (lb.) Vehicle with towing package 1587 (3500) ∗ 1 : Unladen vehicle ∗ 2 : With P215/65R16 tires ∗ 3 : With P225/60R17 tires 2004 SIENNA from Aug. ’04 Prod. (OM45422U)
Page 495: Fuel
“Toyota Genuine Motor Oil” or equivalent “Toyota Genuine Long Life Coolant” is satisfy following grade used in your Toyota vehicle. In order to viscosity. avoid technical problems, we strongly Oil grade: recommend using “Toyota Genuine Long API grade SL “Energy−Conserving” or Life Coolant”...
Page 496 Above −18_C (0_F) Fluid type: Toyota Genuine ATF Type T−IV SAE 90 SAE J1703 or FMVSS No.116 DOT 3 Change automatic transmission fluid only Below −18_C (0_F) as necessary. SAE 80W or 80W−90 2004 SIENNA from Aug. ’04 Prod. (OM45422U)
Page 497: Tires
Wheel nut torque, N·m (kgf·m, ft·lbf): 103 (10.5, 76) NOTE: For a complete information on tires (e.g. replacing tires or replacing wheels), see “Checking tire inflation pressure” through “Aluminum wheel precautions”, pages 463 through 474, in Section 7−2. 2004 SIENNA from Aug. ’04 Prod. (OM45422U)
Page 498: Fuses
4. DRL 20 A: Daytime running light sys- tion system tem, “H−LP RH” and “H−LP LH” fuses 5. ALT−S 7.5 A: Charging system Engine compartment 6. H−LP LL 15 A: Left−hand headlight (low beam), front fog lights 2004 SIENNA from Aug. ’04 Prod. (OM45422U)
Page 499 04 SIENNA_U (L/O 0408) 13. DOME 10 A: Interior lights, personal 26. PWR OUTLET 15 A: Power outlets 38. ECU−IG 10 A: Toyota park assist sys- lights, vanity lights, door courtesy tem, rear view monitor system, multi- 27. CIG 15 A: Cigarette lighter...
Page 500 53. AM2 30 A: “INJ”, “IGN” and “GAUGE2” Fuse (type D) fuses 67. ALT 140 A: Charging system, “RR 54. P/SEAT 30 A: Power seats A/C”, “HTR”, “FAN”, “PBD”, “R−PSD”, “L−PSD” and “DEF” fuses 55. PWR 30 A: Power windows 2004 SIENNA from Aug. ’04 Prod. (OM45422U)
Page 501 Reporting safety defects for U.S. owners Reporting safety defects for U.S. owners ..... . 2004 SIENNA from Aug. ’04 Prod. (OM45422U)
Page 502 However, NHTSA cannot become involved in individual problems between you, your dealer, or Toyota Motor Sales, U.S.A., Inc. 2004 SIENNA from Aug. ’04 Prod. (OM45422U)
Page 503 API grade SL “Energy−Conserving” or ILSAC multigrade engine oil is recommended. See page 457 for detailed information. Tire information: See pages 463 through 474. Tire inflation pressure: See page 491. Publication No. OM45422U Part No. 01999-45422 Printed in Japan 01−0408−00 2004 SIENNA from Aug. ’04 Prod. (OM45422U)
Page 504 The Toyota authorized Repair Manual is packed with literally everything you need to know to perform your own maintenance in virtually every area of your new vehicle. 2004 SIENNA from Aug. ’04 Prod. (OM45422U)
Page 505 Toyota dealer. Areas covered include such things as spark plug re- Pub. Name: 2004 SIENNA Repair Manual placement, valve clearance adjustment and engine oil Pub. No.: RM1025U1 and filter replacement. RM1025U2 2004 SIENNA from Aug. ’04 Prod. (OM45422U)

Toyota 2004 Sienna Owner's Manual

1 2 Section −

1 3 Section −

1 4 Section −

1 5 Section −

1 6 Section −

1 7 Section −

1 8 Section −

1 9 Section −

2 Section

3 Section

4 Section

6 Section

7 1 Section −

7 2 Section −

Quick Links

Chapters

Related Manuals for Toyota 2004 Sienna

Summary of Contents for Toyota 2004 Sienna