Download Print this page

Whirlpool WHEMB40 Installation And Operation Manual

Hide thumbs

Advertisement

Quick Links

Model WHEMB40
How to install, operate
and maintain your
Microbiological
Drinking Water Purifier
Do not return unit to store
If you have any questions or concerns when
installing, operating or maintaining your drinking
water purifier, call our toll free number:
1-866-986-3223
Monday- Friday, 8 AM - 7 PM EST or visit
www.ecodynewatertreatment.com
When you call, please be prepared to provide
the model, date code and serial number of your
product, found on the rating decal, located
inside the cover.
System tested and certified by NSF International
against NSF/ANSI Standards 42 & 53.
See performance data sheet for details.
Manufactured and warranted by
Ecodyne Water Systems
1890 Woodlane Drive
Woodbury, MN 55125
7312474 (Rev G 5/12/14)

Advertisement

loading

  Also See for Whirlpool WHEMB40

  Related Manuals for Whirlpool WHEMB40

  Summary of Contents for Whirlpool WHEMB40

  • Page 1 Model WHEMB40 How to install, operate and maintain your Microbiological Drinking Water Purifier Do not return unit to store If you have any questions or concerns when installing, operating or maintaining your drinking water purifier, call our toll free number:...
  • Page 2: Table Of Contents

    This warranty applies to consumer-owned installations only. ® Registered trademark/TM Trademark of Whirlpool, USA. Manufactured under license by Ecodyne Water Systems, Woodbury, Minnesota. © 2010 Whirlpool Corporation. All rights reserved.
  • Page 3: What The Microbiological Drinking Water Purifier Will Do

    The WHEMB40 utilizes patented technology to ensure a safe water supply for the user. Replace all filters every 6 months or 350 gallons. The purifier technology is designed to stop flowing when its capability to protect the user has been exhausted.
  • Page 4: Parts Of The System

    Parts of the System Filter system assembly Water supply fitting Filtered water faucet for sink or countertop mounting Color coded 3/8" tubing to make all needed connections Materials and Tools Needed NOTE: Gather the required tools before starting installation. Read and follow the instructions provided with any tools listed here.
  • Page 5: Installation Instructions

    Installation Instructions Step A - Install Supply Water Fitting Check and comply with local plumbing codes as you plan, then install a cold feed (supply) water fitting. The fitting must provide a leak-tight connection to the water filter 3/8" tubing. A typical connection using the included water supply fitting is shown in Figure 3A.
  • Page 6: Step B - Make Hole For Filtere Water Faucet

    Installation Instructions Step C - Install Faucet 1. Feed the 3/8" tubing that is attached to the faucet through the mounting hole. Slide the toggle bolts through the mounting hole. Tighten the screws to secure the base flat on the mounting surface. Do not overtighten.
  • Page 7: Step E - Turn On Water, Check For Leaks And Rinse Carbon Fines

    Installation Instructions continued from the previous page Connect Tubing: 1. Use a sharp cutter or knife to cut the end of tubing square. 2. Inspect the end (about 1") of the tubing to be sure there are no nicks, scratches or other rough spots. If needed cut the tubing again.
  • Page 8: Filter Cartridges

    Whilrpool Microbiological Drinking Water Purifier system model WHEMB40 with replacement element pack WHEMBF0 conforms to NSF/ANSI 42 and 53 for the specific performance claims as verified and substantiated by test data.
  • Page 9: Faucet Electronics & Battery Change

    Faucet Electronics Faucet Timer Inside the faucet base is a battery operated 6 month timer. An amber LED indicator is also located in the front of the faucet base. This LED will flash continuously after 6 months have passed. This indicates that it is time to replace the battery and filters. Battery Change To change the battery, complete the following steps.
  • Page 10: Exploded View & Parts List

    Exploded View Questions? Call Toll Free 1-866-986-3223 Monday- Friday, 8 AM - 7 PM EST or visit www.ecodynewatertreatment.com When you call, please be prepared to provide the model, date code and serial number, found on the rating decal, located inside the cover.
  • Page 11: Parts List

    Parts List Key No. Part No. Description 7292674 Faucet, Chrome, with base & electronics 7315121 Cover (order decal below) – 7313585 Decal, Cover 7228536 Tee, Feed Adaptor 7168435 Tubing, 3/8” OD x 72” long, White 7313682 Repl. Head Assembly Repl. Filter Cartridges, WHEMBF0 1 each of Sediment, LTO (Lead, Taste &...