Table of Contents
Advertisement
Advertisement
Table of Contents
Related Manuals for Mitsubishi Electric MSZ-GL25VGD
Summary of Contents for Mitsubishi Electric MSZ-GL25VGD
- Page 1 SPLIT-TYPE AIR CONDITIONERS INDOOR UNIT MSZ-GL25VGD MSZ-GL35VGD MSZ-GL42VGD MSZ-GL50VGD MSZ-GL60VGD MSZ-GL71VGD MSZ-GL80VGD For user OPERATING INSTRUCTIONS • To use this unit correctly and safely, be sure to read these operating English instructions before use.
-
Page 2: Safety Precautions
● OPERATING INSTRUCTIONS ● ONTENTS I SAFETY PRECAUTIONS I NAME OF EACH PART I PREPARATION BEFORE OPERATION I SELECTING OPERATION MODES I FAN SPEED AND AIRFLOW DIRECTION ADJUSTMENT I LONG OPERATION I POWERFUL OPERATION I I-SAVE OPERATION I ECONO COOL OPERATION I TIMER OPERATION (ON/OFF TIMER) I WEEKLY TIMER OPERATION I DEMAND RESPONSE AND INDOOR UNIT OPERATION... -
Page 3: For Installation
AFETY PRECAUTIONS WARNING CAUTION When the air conditioner does not cool or heat, there is a pos- Replace all batteries of the remote controller with new ones of sibility of refrigerant leakage. If any refrigerant leakage is found, the same type. stop operations and ventilate the room well and consult your •... -
Page 4: Indoor Unit
● OPERATING INSTRUCTIONS ● AME OF EACH PART Indoor unit Remote controller <GL25/35/42/50/60> Heat Signal transmitting exchanger section Front panel Distance of signal : Air inlet About 6 m Air fi lter Beep(s) is (are) heard from the indoor unit Air cleaning fi... -
Page 5: Installing The Remote Controller Batteries
REPARATION BEFORE OPERATION Before operation: Insert the power supply plug into the power outlet and/or turn the breaker on. Installing the remote controller batteries Press RESET. Remove the front lid. Insert the negative pole of AAA alkaline batteries fi rst. Install the front lid. -
Page 6: Emergency Operation
● OPERATING INSTRUCTIONS ● ELECTING OPERATION MODES AUTO mode (Auto change over) The unit selects the operation mode according to the difference between the room temperature and the set temperature. During AUTO mode, the unit changes mode (COOL↔HEAT) when the room temperature is 2°C away from the set temperature for more than 15 minutes. -
Page 7: Airflow Direction
AN SPEED AND AIRFLOW DIRECTION ADJUSTMENT <GL25/35/42/50/60> <GL71/80> Press to select fan speed. Each press changes Press to select fan speed. Each press changes fan speed in the following order: fan speed in the following order: (AUTO) (Quiet) (Low) (Med.) (High) (Super High) (AUTO) (Quiet) -
Page 8: Save Operation
● OPERATING INSTRUCTIONS ● ONG OPERATION SAVE OPERATION <GL71/80 only> Press during COOL, ECONO COOL, or HEAT mode to select i-save mode. Press to start LONG operation. • Fan speed increases and the horizontal vane moves to the position for LONG mode. -
Page 9: Econo Cool Operation
CONO COOL OPERATION Press during COOL mode page 5 to start ECONO COOL operation. The unit performs swing operation vertically in various cycles according to the temperature of airflow. Press again to cancel ECONO COOL operation. • ECONO COOL operation is canceled when the VANE, LONG, or POWERFUL button is pressed. -
Page 10: Weekly Timer Operation
● OPERATING INSTRUCTIONS ● EEKLY TIMER OPERATION • A maximum of 4 ON or OFF timers can be set for individual days of the week. • A maximum of 28 ON or OFF timers can be set for a week. Press , and to set ON/OFF, time, and temperature. - Page 11 EMAND RESPONSE AND INDOOR UNIT OPERATION Demand response This unit has demand response capability which is compliant with AS/NZS 4755.3.1. To activate this function, you need to make a contract with remote agents such as electric supply company, then this unit should be connected to Demand response enabling devise (DRED).
-
Page 12: Front Panel
● OPERATING INSTRUCTIONS ● LEANING Instructions: • Switch off the power supply or turn off the breaker before cleaning. • Use only diluted mild detergents. • Be careful not to touch the metal parts with your hands. • Do not expose parts to direct sunlight, heat, or fi re to dry. •... -
Page 13: When You Think That Trouble Has Occurred
HEN YOU THINK THAT TROUBLE HAS OCCURRED Symptom Explanation & Check points Even if these items are checked, when the unit does not recover from the Remote controller trouble, stop using the air conditioner and consult your dealer. The display on the remote •... - Page 14 ● OPERATING INSTRUCTIONS ● ● OPERATING INSTRUCTIONS HEN YOU THINK THAT TROUBLE HAS OCCURRED In the following cases, stop using the air conditioner and consult your dealer. • When water leaks or drips from the indoor unit. • When the upper operation indicator lamp blinks. •...
-
Page 15: Electrical Work
HEN THE AIR CONDITIONER IS NOT NSTALLATION PLACE AND GOING TO BE USED FOR A LONG TIME ELECTRICAL WORK Installation place Set to the highest temperature in manual COOL mode, Avoid installing the air conditioner in the following places. and operate for 3 to 4 hours. Page 5 •... - Page 16 HEAD OFFICE: TOKYO BLDG., 2-7-3, MARUNOUCHI, CHIYODA-KU, TOKYO 100-8310, JAPAN JG79A991H01...