Table of Contents
Advertisement
QQ
3 7 63 1515 0
MAIN BOARD IC101 M30620MCP-A18FPU0 (SYSTEM CONTROLLER)
Pin No.
Pin Name
1
SYS_RXD
2
SYS_CLK
3
CEC_RX_IN
4
SIRCS_IN
5
CODEC_DO
6
CODEC_DI
7
CODEC_CLK
8
BYTE
9
CNVss
10
CODEC_PDN
11
CODEC_CS
12
RESET
13
Xout
14
Vss
15
Xin
16
Vcc1
17
NMI
18
CODEC_INT
19 to 21
-
TE
22
CEC_TX_OUT
L 13942296513
23
VIDEO_MUTE 0
BACKLIGHT_
24
LED1
25
V_SEL
BACKLIGHT_
26
LED2
27
DMPORT_DET
28
VIDEO_MUTE1
29
I2C_CLK
30
I2C_DATA
31
DMPORT_TX_OUT
32
DMPORT_RX_IN
33
CLK1
34
RTS1
35
DVD_SID
36
DVD_SOD
37
DVD_SCO
38
SYS_WAKEUP
39, 40
-
41
EPM
42, 43
-
www
44
P_CONT1
45
P_CONT_TS
.
46
FLASH_CE
47
P_CONT_FL
48
EJECT_KEY
http://www.xiaoyu163.com
I/O
O
Serial data output to the SYSTEM CONTROL connector (SA-WSIS10)
O
Serial data transfer clock signal output to the SYSTEM CONTROL connector (SA-WSIS10)
I
CEC serial data input from the HDMI OUT connector
I
SIRCS signal input from the remote control receiver
O
Serial data output to the A/D converter
I
Serial data input from the A/D converter
O
Serial data transfer clock signal output to the A/D converter
I
External data bus width selection signal input terminal Fixed at "L" in this set
I
Processor mode switch input terminal (for test)
O
Reset signal output to the A/D converter "L": reset
O
Chip select signal output to the A/D converter
System reset signal input from the SYSTEM CONTROL connector (SA-WSIS10) "L": reset
I
For several hundreds msec. after the power supply rises, "L" is input, then it change to "H"
O
Main system clock output terminal (10 MHz)
-
Ground terminal
I
Main system clock input terminal (10 MHz)
-
Power supply terminal (+3.3V)
I
Non-maskable interrupt input terminal Fixed at "H" in this set
I
Interrupt signal input from the A/D converter
-
Not used
O
CEC serial data output to the HDMI OUT connector
O
Video signal input selection signal output terminal
O
LED drive signal output terminal
O
Video signal input selection signal output terminal
O
LED drive signal output terminal
I
Connect detection signal input from the DMPORT jack
O
Video signal input selection signal output terminal
I/O
Two-way I2C clock bus terminal Not used
I/O
Two-way I2C data bus terminal Not used
O
Serial data output to the DMPORT connector
I
Serial data input from the DMPORT connector
-
Not used
-
Not used
O
Serial data output to the servo DSP
I
Serial data input from the servo DSP
I
Serial data transfer clock signal input from the servo DSP
O
System wake up signal output to the SYSTEM CONTROL connector (SA-WSIS10)
-
Not used
I
Not used
-
Not used
O
Power on/off control signal output terminal "H": power on
x
ao
u163
y
O
Power on/off control signal output terminal for the touch sensor "H": power on
i
-
Not used
O
Power on/off control signal output terminal for the front panel section "H": power on
I
Front panel key input terminal for the eject (A/D input)
http://www.xiaoyu163.com
2 9
8
Description
Q Q
3
6 7
1 3
1 5
co
.
HCD-IS10
9 4
2 8
0 5
8
2 9
9 4
2 8
m
9 9
9 9
61
Hide quick links:
Advertisement
Table of Contents
