Page 1 When it comes to service, remember that your Toyota dealer knows your vehicle best and is interested in your complete satisfaction. He will provide quality maintenance and any other assistance you may require. If there is not a Toyota dealer near you, or you need emergency assistance for any reason, please call the following number: U.S. OWNERS: Toyota Customer Assistance Center Toll−free:1−800−331−4331...
Page 2: Important Information About This Manual
Important information about this manual Safety and vehicle damage warnings Safety symbol Throughout this manual, you will see safety and vehicle damage warnings. You must follow these warnings carefully to avoid possible injury or damage. The types of warnings, what they look like, and how they are used in this manual are explained as follows: CAUTION This is a warning against anything which may cause...
Page 3: Occupant Restraint Systems
None of these systems, either indi- Toyota encourages you and your family to take the time vidually or together, can ensure that there is no injury to read Section 1−3 of this Owner’s Manual carefully.
Page 4 In order to be effective, the SRS airbags must deploy with tremendous speed. The rapid deployment of the SRS airbags makes the SRS airbags themselves poten- Your new vehicle is covered by the following Toyota tial sources of serious injury if an occupant is too close limited warranties:...
Page 5 Toyota CAUTION A wide variety of non−genuine spare parts and accesso- ries for Toyota vehicles are currently available in the WARNING: Engine exhaust, some of its constituents, market. You should know that Toyota does not warrant and a wide variety of automobile components contain...
Page 6 293 and traction control system, vehicle stability control system, 224. SRS airbag system and seat belt pretensioner system, be sure to check with your Toyota dealer for precaution- ary measures or special instructions regarding installa- Scrapping of your Toyota tion.
Page 7: Driving Tips
On−pavement and off−road driving tips This vehicle belongs to the utility vehicle class. Utility vehicles have a significantly higher rollover rate than other types of vehicles. This vehicle will handle and maneuver differently from an ordinary passenger car because it is designed for off−road use also.
Page 8 viii 2004 L/C100 from July ’03 Prod. (OM60A04U)
Page 9: Operation Of Instruments And
SECTION − OPERATION OF INSTRUMENTS AND CONTROLS Overview of instruments and controls Instrument panel overview ........Instrument cluster overview .
Page 10: Instrument Panel Overview
Instrument panel overview "View A 1. Side vents 2. Side defroster outlets 3. Instrument cluster 4. Center vents 5. Electric moon roof switches and/or personal lights 6. Glove box 7. Power door lock switches 8. Power window switches 9. Automatic transmission selector lever 10.
Page 11 "View B 1. Headlight, turn signal and front fog light switches 2. Cruise control switch 3. Ignition switch 4. Wiper and washer switches 5. Emergency flasher switch 6. Clock, outside temperature and trip infor- mation display 7. Car audio 8. Front passenger’s seat belt reminder light 9.
Page 12 "Lower part of center cluster panel 1. Ashtray 2. Cigarette lighter 3. Power outlet 2004 L/C100 from Aug ’03 Prod. (OM60A04U)
Page 13: Instrument Cluster Overview
Instrument cluster overview 1. Voltmeter 4. Tachometer 7. Odometer and two trip meters 2. Speedometer 5. Engine oil pressure gauge 8. Trip meter reset knob 3. Service reminder indicators and 6. Engine coolant temperature gauge 9. Fuel gauge indicator lights 2004 L/C100 from Aug ’03 Prod.
Page 14: Indicator Symbols On The Instrument Panel
Indicator symbols on the instrument panel ∗ 1 ∗ 1 Brake system warning light Unengaged “Park” warning light Automatic transmission fluid temperature warning ∗ 1 Driver’s seat belt reminder light ∗ 1 light ∗ 1 Discharge warning light Turn signal indicator lights Engine oil replacement reminder light Headlight high beam indicator light Driving pattern (“POWER”...
Page 15: 1 : For Details, See "Service Reminder Indicators And Warning
vehicle stability control system off indicator ∗ 1 light vehicle stability control system and active traction ∗ 1 control system warning light Active traction control system indicator light Slip indicator light ∗ 3 Roll sensing of curtain shield airbags off indicator light ∗...
Page 16 2004 L/C100 from Aug ’03 Prod. (OM60A04U)
Page 17: Table Of Contents
SECTION − OPERATION OF INSTRUMENTS AND CONTROLS Keys and Doors Keys ............Engine immobilizer system .
Page 18: Keys
When using a key containing a trans- 1. Master keys (black)—These keys work remote control key, see “Wireless remote ponder chip, observe the following in every lock. Your Toyota dealer will control” on page 17. precautions: need one of them to make a new key with a built−in transponder chip.
Page 19 z Do not use the key with electromag- netic materials. z Do not use the key with electromag- netic materials. z When starting the engine, do not z Do not bend the key grip. use the key with other transponder z Do not cover the key grip with any keys around (including keys of oth- material that cuts off electromagnet-...
Page 20: Engine Immobilizer System
Toyota dealer. need additional keys, duplicates can be the electronic code in the chip corre- made by a Toyota dealer using the key The indicator light stays on except sponds to the registered ID code for number.
Page 21: Side Doors
FCC ID: MOZRI−20BTY which enables the engine to start. The MADE IN JAPAN indicator light will go off. For your Toyota dealer to make a new key This device complies with Part 15 of the with a built−in transponder chip, your FCC Rules.
Page 22 LOCKING UNLOCKING WITH POWER DOOR LOCK SWITCH Push the switch. To lock: Push the switch down on the front side. To unlock: Push the switch down on the l12093a rear side. All the side doors and back door lock or unlock simultaneously.
Page 23 —Automatic door locking and unlocking functions You can select the following modes of CAUTION the automatic locking and unlocking functions. The initial mode is mode 1. Before driving, be sure that the doors Mode 1—Automatic locking operation closed locked, especially linked to shift lever position when small children are in the ve- All doors are automatically locked when...
Page 24 SETTING FUNCTIONS 3. Within 10 seconds of turning the igni- To set the mode 4 (the automatic un- tion switch to the “ON” position, press locking operation linked to shift lever You can set the following functions by and hold the front of the driver’s side position): yourself.
Page 25: Wireless Remote Control
NOTE: *The 2−step unlocking function can of the loss of the wireless remote control be changed. **The turn signal lights can be set not to flash. Ask your Toyota deal- key. Ask your Toyota dealer for details. er for details.
Page 26 If you lose your wireless remote control age and trouble on the key. key, contact your Toyota dealer as soon “PANIC” SWITCH as possible to avoid the possibility of Do not leave the key on places where Pushing the “PANIC”...
Page 27 Toyota dealer. user’s authority to operate the equip- couraged to try to correct the interfer- ment.
Page 28 1. Remove the screw, and then the cover. 2. Remove module from 3. Remove the 2 screws to take out the frame. lid of the module. Take out the dis- charged battery and put a new battery with the positive side up. NOTICE Do not bend the terminals.
Page 29: Power Windows
Power windows 4. Install the lid with the 2 screws. 5. Install the module into the key frame and secure the cover with the screw. 6. When pushing any switch on the wire- less key, make sure the indicator light comes on.
Page 30 Window lock switch l12088a 12C007b 12c012a OPERATING THE PASSENGERS’ WIN- Automatic operation: Push the switch DOWS completely down or pull it completely up, and then release it. The window will fully Use the switch on each passenger’s open or close. To stop the window part- door or the switches on the driver’s way, lightly move the switch in the oppo- door that control each passenger’s win-...
Page 31: Power Quarter Windows
Power quarter windows CAUTION Never leave anyone (particularly a small child) alone in your vehicle, To avoid serious personal injury, you especially with the ignition key still must do the following. inserted. Otherwise, could power window Before you close the power win- switches and get trapped in a win- dows, always make sure there is dow.
Page 32: Back Door
Back door CAUTION To avoid serious personal injury, you must do the following. Before you close the power quarter windows, always make sure there is nobody around the power quarter windows. You must also make sure the hands and other parts of the bodies of all occupants are kept completely inside...
Page 33 CAUTION Keep the back door closed while driving. This not only keeps the luggage from being thrown out but also prevents exhaust gases from entering the vehicle. If the open back door hides the stop and tail lights, rear turn signal lights or rear retro reflectors while you are parked, other road users must be warned of the presence of...
Page 34: Hood
Hood CAUTION Before driving, be sure that the back door is closed and locked, especially when small children are in the ve- hicle. Along with the proper use of seat belts, locking the doors helps prevent the driver and passengers from being thrown out from the ve- hicle during an accident.
Page 35: Theft Deterrent System
Theft deterrent system 2. In front of the vehicle, pull up the To deter vehicle theft, the system is SETTING THE SYSTEM auxiliary catch lever and lift designed to sound an alarm if any of 1. Turn the ignition key to the “LOCK” hood.
Page 36 If the battery terminal is disconnected If the system does not work properly, and then reconnected Turn the ignition key from the “LOCK” have it checked by your Toyota dealer. to “ON” position. The indicator light will come on when the system is activating.
Page 37: Fuel Tank Cap
Fuel tank cap 12C503 12C006b This indicates that the fuel filler door 1. To open the fuel filler door, pull the 2. To remove the fuel tank cap, turn is on the left side of your vehicle. lever. slowly counterclockwise, then pause slightly before removing When refueling, turn off the engine.
Page 38: Electric Moon Roof
45 seconds even after the ignition switch Use only a genuine Toyota fuel tank is turned off. It stops working when either cap for replacement. It is designed of the front doors is opened.
Page 39 You must by your Toyota dealer. Jam protection function (closing opera- also make sure nobody places his tion only): If something gets caught be-...
Page 40 Never leave anyone (particularly a small child) alone in your vehicle, especially with the ignition key still inserted. Otherwise, could use the moon roof switches and get trapped in the roof open- ing. Unattended person (particularly a small child) can be involved in a serious accident.
Page 41 SECTION − OPERATION OF INSTRUMENTS AND CONTROLS Occupant restraint systems Seats ............Front seats .
Page 42: Seats
Front seats— —Front seat precautions Seats While the vehicle is being driven, all ve- Driver seat Slightly recline the back of hicle occupants should have the seatback seat. Although vehicle designs vary, upright, sit well back in the seat and prop- CAUTION many drivers can achieve the 250 erly wear the seat belts provided.
Page 43 —Seat adjustment precautions Front passenger seat Front seats (with SRS side airbags) CAUTION CAUTION CAUTION Do not adjust the seat while the vehicle is moving as the seat may The SRS front passenger airbag also The SRS side airbags are installed in unexpectedly move and cause the deploys with considerable force, and the driver and front passenger seats.
Page 44: Adjusting Front Seats
—Adjusting front seats 1. SEAT POSITION AND SEAT CUSHION CAUTION ANGLE ADJUSTING SWITCH Move the control switch in the desired To reduce the risk of sliding under direction. the lap belt during a collision, avoid Releasing the switch will stop the seat at reclining the seatback any more than that position.
Page 45: Armrest
Rear seats— —Rear seat precautions Armrest Tumbling the seats will enlarge the lug- CAUTION gage compartment. See “Cargo and lug- gage” on page 224 for precautions when Do not adjust the seat while the loading luggage. vehicle is moving. Be careful that the seat does not hit a passenger or luggage.
Page 46 —Moving second seat —Adjusting second seats third seat entry SEATBACK ANGLE ADJUSTING LEVER Lean forward and pull the lever toward you. Then lean back to the desired angle and release the lever. CAUTION To reduce the risk of sliding under belt during collision,...
Page 47 —Tumbling second seat CAUTION After returning the seat, make sure the seat is securely locked by push- ing forward and rearward on the top of the seatback and by trying to pull up the edge of the bottom cushion. I13378b I13340a BEFORE TUMBLING SECOND SEAT 2.
Page 48 TUMBLING SECOND SEAT 2. Unlock the seat cushion. Swing the 3. Hook the strap. whole seat up and forward. 1. Lower the outer head restraint to the When returning the second seat to its lowest position and pull up the cen- original position, put the holding strap into ter head restraint.
Page 49 CAUTION When returning seats to their original position, observe the following pre- cautions in order to prevent personal injury in a collision or sudden stop: Make sure the seat is securely locked by pushing forward and rear- ward on the top of the seatback and by trying to pull up the edge of the bottom cushion.
Page 50 —Adjusting third seats —Tumbling third seats SEATBACK ANGLE ADJUSTING LEVER Lean forward and pull the lever toward you. Then lean back to the desired angle and release the lever. CAUTION I13377b To reduce the risk of sliding under belt during collision, avoid reclining the seatback any more than needed.
Page 51 I13262b 2. Make sure the shoulder belt passes TUMBLING THIRD SEAT 2. Unlock the seat cushion and slide through the hanger when folding the the whole seat the rear−most 1. Lower the head restraint to the low- third seat. position while pulling up the handle. est position.
Page 52 13c558 13c559 13c557 3. Swing the whole seat up. 4. Hook the strap. 5. Remove the seat hook covers from the back of the seat cushion, and When returning the third seat to its origi- install them over the seat hooks. nal position, put the holding strap into the hole.
Page 53 —Removing third seats CAUTION When returning seats to their original position, observe the following pre- cautions in order to prevent personal injury in a collision or sudden stop: Make sure the seat is securely locked by pushing forward and rear- ward on the top of the seatback and by trying to pull up the edge of the bottom cushion.
Page 54: Head Restraints
Head restraints CAUTION When reinstalling the seat, be care- ful not to hit the seat against you When removing or reinstalling the or inside of the vehicle. seat, observe the following precau- Install each seat in the same posi- tions to prevent personal injury: tion from which it was removed.
Page 55: Seat Heaters
Seat heaters For your safety and comfort, adjust the Right side CAUTION head restraint before driving. front seat To raise: Pull it up. Occupants must use caution when op- To lower: Push it down while pressing the erating the seat heater because it lock release button.
Page 56: Seat Belts
Seat belts— —Seat belt precautions Toyota strongly urges that the driver and Do not allow any children to stand up or NOTICE passengers in the vehicle be properly re- kneel on either rear or front seats. An strained at all times with the seat belts...
Page 57 —Fastening 3−point seat belts CAUTION Be careful not to damage the belt webbing or hardware. Take care that Persons should ride in their seats they do not get caught or pinched properly wearing their seat belts in the seat or doors. whenever vehicle moving.
Page 58 If the seat belt does not function normally, immediately contact your Toyota dealer. Do not use the seat until the seat belt is fixed, because it cannot protect an adult occupant or your child from injury.
Page 59 CAUTION Always make sure the shoulder belt is positioned across the center of your shoulder. The belt should be l13197b kept away from your neck, but not falling off your shoulder. Failure to do so could reduce the amount of protection in an accident and cause serious injuries in a collision.
Page 60 If the seat belt does not function Keep as low on hips as possible normally, immediately contact your Toyota dealer. Do not use the seat Sit up straight and well back in the Remove excess length of the belt and until the seat belt is fixed, because seat.
Page 61: Seat Belt Extender
Toyota dealer free of charge. Please contact your local Toyota dealer to order the proper required length for the extender. Bring the heaviest coat you ex- pect to wear for proper measurement and selection of length.
Page 62 To connect the extender to the seat Toyota dealer. Do not use the seat the event of collision. belt, insert the tab into the seat belt until the seat belt is fixed, because buckle so that the “PRESS”...
Page 63: Roll Sensing Of Curtain Shield Airbags Off Indicator Light
—Seat belt pretensioners CAUTION Make sure the roll sensing of cur- tain shield airbags indicator light is not on. When the roll sensing of curtain shield airbags off switch is turned on (and the roll sensing of curtain shield airbags off indicator light is on), the seat belt pretensioners will not operate in a vehicle rollover and turning off the seat belt preten-...
Page 64 The airbag can result in death or serious inju- ries. Consult your Toyota dealer sensor assembly consists of a safing sen- about any repair and modification. sor and airbag sensor. 2004 L/C100 from Aug ’03 Prod. (OM60A04U)
Page 65: Buzzers" On
If any of the following conditions occurs, NOTICE this indicates a malfunction of the airbags or seat belt pretensioners. Contact your Do not perform any of the following Toyota dealer as soon as possible. changes without consulting your Toyota dealer.
Page 66: Srs Driver Airbag And Front Passenger Airbag
SRS front airbags are inflated. 13c560 In the following cases, contact your Toyota The SRS (Supplemental Restraint Sys- dealer as soon as possible: tem) front airbags are designed to pro-...
Page 67 The SRS front airbags will deploy if the The driver and front passenger can child restraint system. Toyota severity of the impact is above the de- be killed or seriously injured by the strongly recommends that all in- signed threshold level, comparable to an...
Page 68 Hitting a curb, Falling into or edge of pavement jumping over a Collision from the rear or hard surface deep hole Collision from the side Vehicle rollover Landing hard or vehicle falling The SRS front airbags are not generally The SRS front airbags may also deploy The SRS front airbag system consists designed to inflate if the vehicle is in- if a severe impact occurs to the under-...
Page 69 These Toyota strongly recommends that: toxic gas to help restrain the forward mo- are usually in the nature of minor burns tion of the occupants.
Page 70 Be sure to wear the seat belt with the seat belt extender. For instructions and precautions con- Do not sit on the edge of the seat Toyota strongly recommends that all cerning seating position, or lean against the dashboard when infants and children be placed in “—Front seat precautions”...
Page 71 Failure to follow these instructions can result in death or serious injury. Do not put anything or any part of Consult your Toyota dealer about any your body on or in front of the repair and modification. dashboard or steering wheel pad that houses the front airbag sys- tem.
Page 72 If either of the following conditions occurs, NOTICE this indicates a malfunction of the airbags or seat belt pretensioners. Contact your Do not perform any of the following Toyota dealer as soon as possible. changes without consulting your Toyota dealer.
Page 73 Roll sensing function: In response to a vehicle rollover, the SRS In the following cases, contact your Toyota The SRS (Supplemental Restraint Sys- curtain shield airbags on both sides work dealer as soon as possible:...
Page 74 Toyota tion where the inflation is not desired strongly recommends that all in- (such as extreme−off road driving). fants and children be placed in the rear seats of the vehicle and prop- erly restrained.
Page 75 When you push the roll sensing of curtain CAUTION shield airbags off switch for a few sec- onds with the ignition switch on, the roll Make sure the roll sensing of cur- sensing of curtain shield airbags off indi- tain shield airbags indicator...
Page 76 Collision from the rear Collision from the front The angle of Skidding vehicle vehicle tip−up hitting a curb Vehicle rollover is marginal stone The SRS side airbags are not generally The curtain shield airbags may not in- The curtain shield airbags may inflate designed to inflate if the vehicle is in- flate if the vehicle is subjected to a if the angle of vehicle tip−up is margin-...
Page 77 Collision from Falling into or jump- Hitting a curb, edge of Collision from 13c538a the front ing over a deep hole pavement or hard sur- the rear face Pitch end over end Landing hard or vehicle falling The curtain shield airbags are not gen- The SRS side airbags and curtain shield The SRS side airbag and curtain shield erally designed to inflate if the vehicle...
Page 78 The SRS side airbag and curtain shield When the airbags inflate, they produce a CAUTION airbag system is controlled by the airbag fairly loud noise and release some smoke sensor assembly. The airbag sensor as- and residue along with non−toxic gas. This The SRS side airbags and curtain sembly consists of a safing sensor and does not indicate a fire.
Page 79 Sit up straight and well back in the seat, distributing your weight evenly in the seat. Do not apply excessive weight to the outer side of the seats with side airbags and to the front and rear pillar, front, center 13c562 and rear garnish and roof interior with the curtain shield airbags.
Page 80 Do not allow anyone to kneel on the passenger seat, facing the pas- senger’s side door, since the side airbags and curtain shield airbags could inflate with considerable speed and force. Otherwise, he/she may be killed or seriously injured. 13c563 Special care should be taken espe- cially when you have a small child in the vehicle.
Page 81 Do not hook a hanger, heavy or sharp pointed objects on the coat hook. If the curtain shield airbags inflate, those items will be thrown away with great force or the curtain shield airbags may not activate cor- 13c800b rectly, resulting in death or serious injury.
Page 82 Such changes may disable curtain shield airbags to inflate ac- Toyota dealer. Such changes can in- the system or cause the curtain cidentally, resulting in death or seri- terfere with proper operation of the shield airbags to inflate accidental- ous injury.
Page 83 If either of the following conditions occurs, this indicates a malfunction of the airbags or seat belt pretensioners. Contact your Toyota dealer as soon as possible. When the ignition key is turned to the “ON” position, the light does not come on, remains on or flashes.
Page 84: Child Restraint
Child restraint— —Child restraint precautions In the following cases, contact your Toyota Toyota strongly urges the use of ap- Toyota strongly urges use of dealer as soon as possible: propriate child restraint systems for proper child restraint system which children.
Page 85 —Child restraint system A child restraint system for a small On vehicle with side airbags and Make sure you have complied with child or baby must itself be properly curtain shield airbags, do not allow all installation instructions provided restrained on the seat with either the the child to lean his/her head or by the child restraint manufacturer lap belt or the lap portion of the lap/...
Page 86 —Types of child restraint system Child restraint systems are classified into the following 3 types depending on the child’s age and size. (A) Infant seat (B) Convertible seat (C) Booster seat Install the child restraint system following the instructions provided by its manufac- turer.
Page 87 —Installation with 2−point type seat belt (A) INFANT SEAT INSTALLATION 1. Run the center lap belt through or CAUTION around the infant seat following the An infant seat must be used in rear− instructions provided by its manufactur- facing position only. Do not install a child restraint system er and insert the tab into the buckle on the third seat if it interferes with...
Page 88 2. While pressing the infant seat firmly Contact your Toyota dealer CAUTION against the seat cushion and seatback, immediately. Do not install the child tighten the lap belt by pulling its free...
Page 89 3. To remove the infant seat, press the (B) CONVERTIBLE SEAT INSTALLATION CAUTION buckle release button. A convertible seat must be used in for- ward−facing or rear−facing position de- Do not install a child restraint system pending on the age and size of the on the third seat if it interferes with child.
Page 90 1. Run the center lap belt through or 2. While pressing convertible seat Contact your Toyota dealer around the convertible seat following firmly against the seat cushion and immediately. Do not install the child instructions provided...
Page 91 —Installation with 3−point type seat belt 13c564 3. To remove the convertible seat, press (A) INFANT SEAT INSTALLATION CAUTION the buckle release button. An infant seat must be used in rear− facing position only. Push and pull the child restraint sys- tem in different directions to be sure it is secure.
Page 92 13c565 1. Run the lap and shoulder belt through CAUTION Do not install a child restraint sys- or around the infant seat following the tem on the third seat if it interferes instructions provided by its manufactur- Never install a rear−facing child re- with the lock mechanism of the sec- er and insert the tab into the buckle straint system on the front passen-...
Page 93 2. Fully extend the shoulder belt to put it 3. While pressing the infant seat firmly Contact your Toyota dealer in the lock mode. When the belt is against the seat cushion and seatback, immediately. Do not install the child...
Page 94 13c566 4. To remove the infant seat, press the (B) CONVERTIBLE SEAT INSTALLATION CAUTION buckle release button and allow the A convertible seat must be used in for- belt to retract completely. The belt will ward−facing or rear−facing position de- Push and pull the child restraint sys- move freely again and be ready to pending on the age and size of the...
Page 95 On vehicle with side airbags and curtain shield airbags, do not allow the child to lean his/her head or any part of his/her body against the door or the area of the seat, front or rear pillar, front, center or rear 13c568 13c567 garnish or roof interior from which...
Page 96 1. Run the lap and shoulder belt through Contact your Toyota dealer Do not install a child restraint sys- or around the convertible seat following immediately. Do not install the child tem on the third seat if it interferes...
Page 97 2. Fully extend the shoulder belt to put it 3. While pressing convertible seat CAUTION in the lock mode. When the belt is firmly against the seat cushion and then retracted even slightly, it cannot seatback, let the shoulder belt retract Push and pull the child restraint sys- be extended.
Page 98 13c569 13c570 Move seat fully back 4. To remove the convertible seat, press (C) BOOSTER SEAT INSTALLATION CAUTION the buckle release button and allow the A booster seat must be used in for- belt to retract completely. The belt will ward−facing position only.
Page 99 On vehicle with side airbags and CAUTION curtain shield airbags, do not allow the child to lean his/her head or Always make sure the shoulder belt any part of his/her body against the is positioned across the center of door or the area of the seat, front child’s shoulder.
Page 100 Contact your Toyota dealer immediately. Do not install the child 13C001 restraint seat on the seat until the seat belt is fixed. 2. To remove the child restraint system, Follow the procedure below for a child...
Page 101 Symbol 13C003 13C004 Anchor brackets Use the anchor bracket located behind the TO USE THE ANCHOR BRACKET: 2. Fix the child restraint system with second seat on the floor to attach the top the seat belt. 1. Remove the head restraint. strap.
Page 102 —Installation with child restraint lower anchorages 13C005 13C532d 13C529 4. Replace the head restraint. The lower anchorages for the child re- CHILD RESTRAINT SYSTEM INSTALLA- straint system interfaced with TION FMVSS225 specification are installed in 1. Take off the cover between the seat the second seat.
Page 103 Type A— CAUTION 2. Latch the hooks of lower straps onto the anchorages and tighten the lower When using the lower anchorages straps. for the child restraint system, be Type B— sure that there are no irregular ob- jects around the anchorages or that 2.
Page 104 2004 L/C100 from Aug ’03 Prod. (OM60A04U)
Page 105 SECTION − OPERATION OF INSTRUMENTS AND CONTROLS Steering wheel and Mirrors Power tilt and telescopic steering wheel ......Outside rear view mirrors .
Page 106: Power Tilt And Telescopic Steering Wheel
This feature can be set inoperative. Ask ries. your Toyota dealer. 2004 L/C100 from Aug ’03 Prod. (OM60A04U)
Page 107: Outside Rear View Mirrors
—Power rear view mirror control Outside rear view mirrors— CAUTION Do not adjust the mirror while the vehicle is moving. Doing so may cause the driver to mishandle the vehicle and an accident may occur resulting in death or serious inju- ries.
Page 108: Anti−Glare Inside Rear View Mirror
Anti−glare inside rear view mirror— —Folding rear view mirrors NOTICE If ice should jam the mirror, do not operate the control or scrape the mir- ror face. Use a spray de−icer to free the mirror. 13C010 The rear view mirrors can be folded Adjust the mirror so that you can just backward for parking in compact areas.
Page 109 —Compass When the ignition key is inserted and Pushing the “AUTO” button for longer turned on, the inside rear view mirror al- 3 seconds turns on or off the compass ways turns on in the “AUTO” mode. display. When the outside air temperature is low, The compass may not show the correct it may take a little longer for the mirror direction in the following conditions:...
Page 110 NOTICE Do not put magnets or a metal object near the inside rear view mirror. Do- ing this may cause malfunction of the compass sensor. CALIBRATING THE COMPASS (deviation calibration) The direction display on the compass deviates from the true direction deter- mined by the earth’s magnetic field, The amount of deviation varies according to the geographic position of the vehicle.
Page 111 If the direction is displayed several sec- onds after adjustment, the calibration is finished. CAUTION Do not adjust the display while the vehicle is moving. Be sure to adjust the display only when the vehicle is stopped. 13C015a Zone number L Hawaii is included in zone 6.
Page 112 Do not adjust the display while the If calibration cannot be performed because vehicle is moving. Be sure to adjust of the magnetized vehicle, etc., take your the display only when the vehicle is vehicle to Toyota dealer. stopped. 2004 L/C100 from Aug ’03 Prod. (OM60A04U)
Page 113: Sun Visors
Sun visors— —Vanity mirror To block out glare, move the sun visor. To block the glare from the front when the To use the vanity mirror, swing down main sun visor is swung down, swing the main sun visor and open the cover. To block out glare from the front—Swing down the second sun visor.
Page 114 2004 L/C100 from Aug ’03 Prod. (OM60A04U)
Page 115 SECTION − OPERATION OF INSTRUMENTS AND CONTROLS Lights, Wipers and Defogger Headlight and turn signals ........Emergency flashers .
Page 116: Headlight And Turn Signals
NOTE: *The operating condition or sensi- tivity can be changed. Ask your Toyota dealer for details. HEADLIGHTS The automatic light control sensor is on the top of the passenger’s side instrument...
Page 117 “LOCK” but- ton on the wireless remote control key turns off the headlights. NOTE: *The time before turning off the lights can be changed. Ask your Toyota dealer for details. NOTICE To prevent the battery from being dis-...
Page 118: Emergency Flashers
Emergency flashers High−Low beams—For high beams, turn TURN SIGNALS To turn on the emergency flashers, the headlights on and push the lever away push the switch. To signal a turn, push the headlight/ from you (position 1). Pull the lever to- All the turn signal lights will flash.
Page 119: Instrument Panel Light Control
Instrument panel light control Front fog lights NOTICE To prevent the battery from being dis- charged, do not leave the switch on longer than necessary when the en- gine is not running. To adjust the brightness of the instru- To turn on the front fog lights, twist ment panel lights, turn the dial.
Page 120: Interior Lights
NOTE: *The interior lights can be set not to come on or the duration of lighting can be changed. Ask your Toyota dealer for details. Rear 2004 L/C100 from Aug ’03 Prod. (OM60A04U)
Page 121: Personal Lights
Personal lights INTERIOR LIGHTS CUT OFF OPERATION To turn on the personal light, push the switch on 1 side. To turn the lights off, When the ignition switch is “OFF” and any push the switch on 2 side. interior lights in the vehicle stay lighting PERSONAL LIGHTS CUT OFF OPERA- on, the lights will cut off automatically TION...
Page 122: Ignition Switch Light
3. “HI” position: High speed operation blocked. If a nozzle becomes blocked, contact your Toyota dealer to have the Twist the interval adjuster upward to in- vehicle serviced. crease the wiping time interval between sweeps, and downward to decrease it.
Page 123: Rear Window Wiper And Washer
Rear window wiper and washer Rear window defogger NOTICE Do not operate the rear wiper if the rear window is dry. It may scratch the glass. To turn on the rear window wiper, twist To defog or defrost the rear window, the lever knob upward.
Page 124: Outside Rear View Mirror Heaters
Outside rear view mirror heaters Make sure you turn the defogger off when CAUTION the surfaces are clear. Leaving the defog- ger on for a long time could cause the Since the mirror surfaces can get hot, battery discharge, especially during do not touch them when the mirror stop−and−go driving.
Page 125 SECTION − OPERATION OF INSTRUMENTS AND CONTROLS Gauges, Meters and Service reminder indicators Fuel gauge ..........Engine coolant temperature gauge .
Page 126: Fuel Gauge
Fill the fuel tank immediately. The indicator lamp goes off after driving several times. If the indicator lamp does not go off, contact your Toyota dealer as soon as possible. 15C004 It is not a malfunction even if the needle of the fuel gauge returns to “E”...
Page 127: Engine Oil Pressure Gauge
If the engine oil pressure should stay be- low the normal range, pull off the road to a safe place and stop the engine immedi- ately. Call a Toyota dealer or qualified repair shop for assistance. Engine oil pressure may not build up when the engine oil level is too low.
Page 128: Voltmeter
Voltmeter Tachometer NOTICE Do not let the indicator needle get into the red zone. This may cause severe engine damage. The voltmeter tells whether the battery The tachometer indicates engine speed is charged discharged. Check in thousands of rpm (revolutions per while the engine is running—the needle minute).
Page 129: Odometer And Two Trip Meters
Odometer and two trip meters 3. Trip meter reset knob—Resets the two trip meters to zero, and also change the meter display. To change the meter display, quickly push and release the knob. The meter display changes in the order from the odometer to trip meter A to trip meter B, then back to the odometer each time you push.
Page 130: Service Reminder Indicators And Warning Buzzers
Service reminder indicators and warning buzzers If the indicator or buzzer comes on... Do this. If parking brake is off, stop immediately and contact Toyota dealer. (Indicator and buzzer) Fasten driver’s seat belt. (Indicator and buzzer) Fasten front passenger’s seat belt.
Page 131 If the indicator or buzzer comes on... Do this. Take vehicle to Toyota dealer. If brake system warning light is also on, stop immediately and contact Toyota dealer. Close all side doors and back door. Shift four−wheel drive control out of “N”.
Page 132 It is dangerous to continue driving Depressing the brake pedal repeatedly a safe place and contact your Toyota normally when the brake fluid level is may turn on the warning light and dealer.
Page 133 (c) Front Passenger’s Seat Belt the nearest Toyota dealer or repair shop. If the light is flashing, we recommend that minder Light you replace the engine oil at an early NOTICE This light reminds you to buckle up the opportunity depending on the driving and front passenger’s seat belt.
Page 134 Have your vehicle the tank as soon as possible. after taking several driving trips. checked by your Toyota dealer as soon as If the lamp will not go off even after sev- possible. eral trips, contact your Toyota dealer as Even if the abnormality of the electronic soon as possible.
Page 135 Contact your After about 6 seconds, the light will go pretensioners have a problem. Toyota dealer as soon as possible to off. This means the system of the air- service the vehicle. bag and front seat belt pretensioners (i) “ABS”...
Page 136 Toyota dealer as soon If the light does not go off, call a Toyota as possible. However, it is no problem (j) Open Door Warning Light dealer or qualified repair shop for assis- that the “VSC/TRAC”...
Page 137: Trip Information Display
“MODE” button, the dis- 2. Open one of the side doors or back above, have it checked by your Toyota played information is changed. door. dealer as soon as possible.
Page 138 Average vehicle speed Driving distance after engine starting Available driving range The average vehicle speed is calculated The driving distance after engine start- The available driving range is calcu- and displayed based on the total driv- ing is displayed. lated and displayed depending on the ing distance and the total driving time amount of remaining fuel.
Page 139 Average fuel consumption after re- Current fuel consumption fueling The current fuel consumption is calcu- The average fuel consumption after re- lated and displayed based on the driv- fueling calculated displayed ing distance and the fuel consumption based on the total driving distance and per 2 second interval with the engine the total fuel consumption after refuel- running.
Page 140 2004 L/C100 from Aug ’03 Prod. (OM60A04U)
Page 141 SECTION − OPERATION OF INSTRUMENTS AND CONTROLS Ignition switch, Transmission and Parking brake Ignition switch with steering lock ......Automatic transmission .
Page 142: Ignition Switch With Steering Lock
Ignition switch with steering lock “ACC”—Accessories such as the radio operate, but the engine is off. If you leave the key in the “ACC” or “LOCK” position and open the driver’s door, a buzzer will remind you to remove the key. “LOCK”—Engine is off and the steering wheel is locked.
Page 143: Automatic Transmission
Automatic transmission Selector lever position P: Parking, engine starting and key removal position R: Reverse position N: Neutral position D: Normal driving position (Shifting into overdrive position) 4: Position for engine braking (Shifting into overdrive not possible) 3,2: Position for more powerful engine braking L: Position for maximum engine braking "...
Page 144 Your automatic transmission has a shift 3. Release the parking brake and brake Shift into the “L” position. The trans- lock system to minimize the possibility of pedal. Depress the accelerator pedal mission will downshift to first gear incorrect operation. This means you can slowly for smooth starting.
Page 145 (c) Using “3”, “2” and “L” positions (d) Backing up NOTICE The “3”, “2” and “L” positions are used for 1. Bring the vehicle to a complete stop. z Be careful not to over-rev the en- strong engine braking as described pre- 2.
Page 146 If the four–wheel drive control is in the When towing a trailer, in order to main- For ordinary driving, Toyota recommends “N” position while the selector lever is in tain engine braking efficiency, do not using the Normal mode to improve fuel the “P”...
Page 147: Four-Wheel Drive System
Four–wheel drive system— (a) Four–wheel drive contro l (i) Driving “2nd STRT” (second Use the center differential lock system if start) mode your wheels get stuck in a ditch, or when you are driving on a slippery or bumpy In the “2nd STRT” (Second start) mode, surface.
Page 148 “H” (high speed position, center differ- In this mode, the braking feeling that oc- Advice for driving on slippery roads in ential unlocked): Lever at “H”, center dif- curs when the wheels are negotiating a “L” (low speed position) mode ferential lock button left out sharp corner is further reduced than in the If you shift the four−wheel drive control...
Page 149 (b) Shifting procedure SHIFTING BETWEEN “H” (UNLOCKED) The four−wheel drive control lever in NOTICE “L” position and the automatic AND “H” (LOCKED) transmission lever in the “R” position For normal driving on dry and hard shift between unlock lock surface roads, unlock the center dif- (As for the automatic transmission lever modes in “H”, push the center differential ferential.
Page 150: Parking Brake
Parking brake Cruise control The cruise control allows you to cruise CAUTION the vehicle at a desired speed over about 40 km/h (25 mph) even with your Before driving, be sure the parking foot off the accelerator pedal. brake is fully released and the park- Your cruising speed can be maintained ing brake reminder light is off.
Page 151 CAUTION To help maintain maximum control of your vehicle, do not use the cruise control when driving heavy or varying traffic, or on slip- – pery (rainy, icy or snow covered) or winding roads. Avoid vehicle speed increases when driving downhill.
Page 152 If this is the case, contact your Toyota cancelled. To decrease the vehicle speed, dealer and have your vehicle inspected. reset to a slower speed with the cruise control lever or depress the brake pedal.
Page 153: Active Traction Control System
If the “VSC/TRAC” warning light comes controlling the output of the brake and on, have your vehicle checked by your engine. Thus, the system assists driver Toyota dealer as soon as possible. control driving power wheels. When you turn the ignition...
Page 154 (The continuous buzzer sounds for about In the following cases, contact your Toyota snow tires or tire chains. Always 3 seconds.) At the time, the “VSC/TRAC”...
Page 155: Vehicle Stability Control System
When replacing the tires or wheels, The system activates when the vehicle substitute for safe driving practices. contact your Toyota dealer. (See speed is about more than 15 km/h (9 “Checking and replacing tires” on Factors including speed, road con- mph).
Page 156 If the “VSC/TRAC” warning light and “VSC OFF” indicator light come on, have your vehicle checked by your Toyota dealer as soon as possible. However, there is no problem if the “VSC/TRAC” warning light comes on when the brake actuator tem- perature becomes high.
Page 157 “VSC OFF” indicator light come on, the vehicle stability control system is not op- erating, but there is no problem if you continue to drive. In the following cases, contact your Toyota dealer: The “VSC/TRAC” warning light, “VSC OFF” indicator light and slip indicator light do not come on after the ignition key is turned “ON”.
Page 158 2004 L/C100 from Aug ’03 Prod. (OM60A04U)
Page 159 SECTION − OPERATION OF INSTRUMENTS AND CONTROLS Car audio system Reference ..........Using your audio system .
Page 160: Reference
—some basics Reference This section describes some of the basic TONE AND BALANCE features on Toyota audio systems. Some For details about your system’s tone and information may not pertain to your sys- balance controls, see the description of tem.
Page 161 The antenna automatically extends when make sure it is retracted before the radio is on, and retracts when the driving your Toyota through an au- radio mode is off. However, even if you tomatic car wash. turn off the radio when the radio on the...
Page 162 YOUR CASSETTE PLAYER When you insert a cassette, the exposed tape should be to the right. NOTICE Do not oil any part of the player and do not insert anything other than cas- sette tapes into the slot, or the tape player may be damaged.
Page 163 —Controls and features Details of specific buttons, controls, and features are described in the alphabetical list that follows. 17c517c 2004 L/C100 from Aug ’03 Prod. (OM60A04U)
Page 164 1 2 3 4 5 6 (Preset buttons) Compact disc (Program) These buttons are used to preset and To eject one compact disc only: Push and Push “ ” to select the other side of a tune in radio stations. release the compact disc eject button.
Page 165 If a tape side rewinds completely, the cas- AUDIO−TUNE Knob DISC (Compact Disc) button sette player will stop and then play that This knob is used to adjust the tone and Push “DISC” to switch from radio or cas- same side. If a tape fast forwards com- balance or to tune the station manually on sette operation to compact disc operation.
Page 166 If the malfunction is not rectified, take FM button Loading one compact disc only— your vehicle to your Toyota dealer. Push “FM” to turn on the radio and select To load one compact disc only, quickly DISC the FM band. “FM1” or “FM2” will appear push and release the button.
Page 167 PWR·VOL (Power and Volume) knob RDS (Radio Data System) display Repeating a track: Quickly push and release “ ” while the Push “PWR·VOL” to turn the audio system The radio will automatically switch to the on and off. Turn “PWR·VOL” to adjust the RDS mode to receive an RDS station track is playing.
Page 168 SCAN button Scanning the tracks on a disc: Cassette Player Quickly push and release “SCAN”. “SCAN” Radio By using this button, you can skip up or will appear on the display and the player down to a different track. You can either scan all the frequencies on will scan all the tracks on the disc you a band or scan only the preset stations You can skip up to nine tracks at a time.
Page 169 After the end of the tape is reached, TAPE button Compact disc player the player will automatically reverse Push “TAPE” to switch from radio or com- This button is used to change the display sides and start playing the other side. pact disc operation to cassette operation.
Page 170: Car Audio System Operating Hints
Car audio system operating hints TRAF (Traffic announcement function) MISC NOTICE button ALERT (Emergency message) To ensure correct audio system op- This button turns the traffic announcement With the program type displayed, push the erations: (TA) feature on and off. This button is “SEEK/TRACK”...
Page 171 Here are some common reception prob- Use high−quality cassettes. lems that probably do not indicate a prob- Fading—AM broadcasts are reflected by Low−quality cassette tapes can cause lem with your radio: the upper atmosphere—especially at night. many problems, including poor sound, These reflected signals can interfere with inconsistent playing...
Page 172 CARING FOR YOUR COMPACT DISC PLAYER AND DISCS The player is intended for use with 12cm (4.7 in.) discs only. Extremely high temperatures can keep your compact disc player from working. On hot days, use the air conditioning to cool the vehicle interior before you listen to a disc.
Page 173 Correct Wrong Labeled discs Handle compact discs carefully, espe- To clean a compact disc: Wipe it with a cially when you are inserting them. soft, lint−free cloth that has been damp- Hold them on the edge and do not ened with water. Wipe in a straight line NOTICE bend them.
Page 174: Rear Seat Audio System
Rear seat audio system (b) When the radio mode is selected (d) When the “CD” mode is selected “ ” button: Push this button to “ DISC ” button: Use this button to select a station preset on the preset but- search a desired disc.
Page 175: Audio Remote Controls (Steering Switches)
Audio remote controls (steering switches) (a) When the radio mode is selected Push this switch briefly for automatic program selection. When automatically “ ” or “ ” switch: Push this switch for selecting a program, you can skip up seek tuning or to select a station. to 9 programs at a time.
Page 176 2004 L/C100 from Aug ’03 Prod. (OM60A04U)
Page 177: For Vehicle Equipped With Navigation System, Please Refer To The Separate "Navigation System Owner's Manual
SECTION − OPERATION OF INSTRUMENTS AND CONTROLS Air conditioning system Front air conditioning system: Controls ..........Air flow selector settings .
Page 178: Front Air Conditioning System: Controls
Front air conditioning system— —Controls 1. Temperature selector knob 2. “AUTO” button 3. Temperature display 4. Fan speed display 5. Air flow display 6. “MODE” button 7. “A/C” button 8. Front windshield button 9. Fan speed control button 10. Air intake control button 11.
Page 179 “AUTO” button “MAX COLD” appears when you adjust to maximum cooling, and “MAX HOT” ap- For automatic operation of the air condi- pears when you adjust to maximum warm- tioning, press the “AUTO” button. An indi- ing. cator light will illuminate to show that the automatic operation mode has been se- “OFF”...
Page 180 4. Floor/Windshield—Air flows mainly When the “A/C” button is not pressed in, from the floor vents and windshield pressing “MODE” button turns off the air vents. conditioning. It is recommended that you close the For details about air flow selector setting, lower vent.
Page 181 If this happens, take your ve- hicle to a Toyota dealer for service. Air intake control button Press the button to select the air source. An indicator light will illuminate to show which air intake mode is being selected.
Page 182: Air Flow Selector Settings
—Air flow selector settings 17C001a “Instrument panel vents” described below. 2004 L/C100 from Aug ’03 Prod. (OM60A04U)
Page 183: Operating Tips
—Operating tips To cool off your Toyota after it has If following another vehicle on a dusty Heating been parked in the hot sun, drive with road, or driving in windy and dusty For best results, set controls to: the windows open for a few minutes.
Page 184 Air conditioning Defogging Defrosting For best results, set controls to: The inside of the windshield The outside of the windshield For best results, set controls to: For best results, set controls to: Fan speed—“AUTO” Temperature—To the desired Temperature—Towards high Temperature—Towards high temperature temperature to heat;...
Page 185: Instrument Panel Vents
—Instrument panel vents Center vents Lower vent If air flow control is not satisfactory, check the instrument panel vents. The instrument panel vents may be opened or closed as shown. For removing frost or fog, it is recom- mended that you close the lower vent when you use the “Floor”, the “Floor/Wind- shield”...
Page 186: Rear Air Conditioning System: Controls
Rear air conditioning system— —Controls 1. Rear air conditioning on−off switch 2. “AUTO” button 3. Air flow selector 4. Fan speed selector 5. Temperature selector 6. “OFF” button 18c507 2004 L/C100 from Aug ’03 Prod. (OM60A04U)
Page 187 Rear air conditioning on−off switch Temperature selector To turn the rear air conditioning on, press Move the lever to adjust the tempera- the “REAR” switch. To turn the rear air ture—to the right to warm, to the left to conditioning off, press the switch again. cool.
Page 188: Air Flow Selector Settings
—Air flow selector settings Air at lower than room temperature does not flow from the floor vents. 18c508 Warm air Cool air 2004 L/C100 from Aug ’03 Prod. (OM60A04U)
Page 189 SECTION − OPERATION OF INSTRUMENTS AND CONTROLS Other equipment Clock ............Outside temperature display .
Page 190: Clock
Clock Outside temperature display For example, if the “:00” button is de- pressed when time between 1:01—1:29, the time will change to 1:00. If the time is between 1:30—1:59, the time will change to 2:00. If the electrical power source has been disconnected from the clock, the time dis- play will automatically be set to 1:00 (one o’clock).
Page 191: Rear View Monitor System
When replacing the tires, please consult your Toyota dealer. If you replace the tires, the area displayed on the screen may change. 2004 L/C100 from Aug ’03 Prod. (OM60A04U)
Page 192 AREA DISPLAYED ON SCREEN The area detected by the camera is limited. Objects which are close to Image is displayed approximately level either corner of the bumper or under on screen. the bumper cannot be seen on the screen. The area displayed on the screen may vary according to vehicle orien- tation or road conditions.
Page 193 When water droplets are adhering to the camera, or when humidity is high (for example, when it rains) When foreign matter (for example, snow or mud) adheres to the camera lens 19C509 When the sun or the beam of head- lights is shining directly into the cam- era lens Check surroundings for safety.
Page 194: Cigarette Lighter And Ashtray
Do not hold the cigarette lighter pressed may cause troubles or short cir- cuits. Use a Toyota genuine cigarette lighter or equivalent for replacement. 2004 L/C100 from Aug ’03 Prod. (OM60A04U)
Page 195: Roll Sensing Of Curtain Shield Airbags Off Switch
Roll sensing of curtain shield airbags off switch Instrument panel Rear console box (Vehicles with naviga- The roll sensing of curtain shield airbags tion system) off switch can turn off the curtain shield airbags and front seat belt pre- tensioners in a vehicle rollover. This switch should only be used in a situa- tion where the inflation is not desired (such as extreme off−road driving).
Page 196: Rear Console Box
Rear console box In a severe side impact, the curtain shield CAUTION airbags on impacted side will inflate even if the roll sensing function is turned off. Make sure the roll sensing of cur- If the ignition switch is turned to “ACC” or tain shield airbags off indicator light “LOCK”...
Page 197: Glove Box
Glove box Garage door opener The battery side of the hand−held trans- mitter must be pointed away from the Buttons HomeLink during the programming pro- Indicator cess. light For Canadian users, follow the procedure in “Programming an entrance gate/Pro- gramming all devices in the Canadian market”.
Page 198 5. Test the operation of the HomeLink 1. Locate the “training” button on the ceil- Programming an entrance gate/Program- pressing the newly programmed button. ing mounted garage door opener motor. ming all devices in the Canadian market If programming a garage door opener, The exact location and color of the 1.
Page 199 15. Operation is subject to the fol- security systems, home door locks or When programming the HomeLink lowing two conditions: (1) This device lighting, contact your authorized Toyota Universal Transceiver, you may be may not cause harmful interference, and dealer for assistance.
Page 200: Auxiliary Boxes
Auxiliary boxes— To use the auxiliary boxes, open the lids as shown in the following illustra- tions. CAUTION To reduce the chance of injury in case of an accident or a sudden stop, always keep the auxiliary box closed while driving. NOTICE Type A (luggage compartment) Type C (rear console)
Page 201: Cup Holders
—First−aid kit holder —Warning reflector holder Cup holders The cup holder is designed for holding cups or drink−cans securely. To use them, observe the following illustra- tions. CAUTION Do not place anything else other than cups or drink−cans in the cup holder, such items...
Page 202 19C008 For front seats For front seat For second seats The cup holder can be adjusted to the To use a cup holder in the console box. size of cups by changing the separator 1. Open the console box lid. Pull down position or moving the separator arms.
Page 203: Card Holder
Card holder Tie−down hooks For third seats (left−hand side) You can store a card in the slot as To secure your luggage, use the tie− shown in the illustration. down hooks as shown above. See “Cargo and luggage” on page 224 for precautions when loading luggage.
Page 204: Cargo Net Hooks
Cargo net hooks Roof luggage carrier Side Cross knobs rails Upper knob Roof rails These hooks are designed to hang car- The roof luggage carrier consists of ADJUSTING THE POSITION OF CROSS go net. roof rails and sliding cross rails. RAILS: To hang the cargo net, use the cargo net 1.
Page 205 Follow the manufacture’s instructions and precautions when installing the attach- ments or their equivalent. CAUTION When you load cargo on the roof lug- gage carrier, observe the following: Place the cargo so that its weight is distributed evenly between the front and rear axles.
Page 206: Floor Mat
Floor mat If driving for a long distance, on rough roads, or at high speeds, stop the vehicle now and then dur- ing the trip to make sure the cargo remains in its place. Do not exceed 70 kg (154 lb.) cargo weight on the roof luggage carrier.
Page 207: Coat Hooks
Coat hooks To use the coat hook, push the hook. CAUTION Do not hook a hanger, heavy or sharp pointed object on the coat hook. If curtain shield airbags inflate, those items will be hurled away with great force or the curtain shield air- bags may not active correctly.
Page 208 2004 L/C100 from Aug ’03 Prod. (OM60A04U)
Page 209 INFORMATION BEFORE DRIVING YOUR TOYOTA Information before driving your Toyota Off−road vehicle precautionss .......
Page 210: Off−Road Vehicle Precautionss
Off−road vehicle precautions This vehicle belongs to the utility ve- CAUTION hicle class, which has higher ground clearance and narrower tread in relation Always observe the following precau- to the height of its center of gravity to tions to minimize the risk of serious make it capable of performing in a wide personal injury or damage to your ve- variety of off−road applications.
Page 211: Break−In Period
To help prevent gas station mix−ups, your hicle more sensitive side to the future economy and long life of Toyota has a smaller fuel tank opening. winds than an ordinary passenger your vehicle: The special nozzle on pumps with un- car. Slowing down will allow you Avoid full−throttle...
Page 212 10% ethanol or 15% Automotive manufacturers in the U.S., heavy knocking. If it is severe, this will MTBE. If you use gasohol in your Toyota, Europe and Japan have developed a lead to engine damage. be sure that it has an octane rating no low-...
Page 213: Fuel Pump Shut Off System
Operation in foreign countries GASOLINE QUALITY The fuel pump shut off system stops sup- If you plan to drive your Toyota in plying fuel to the engine when the engine another country... In a very few cases, you may experience stalls or an airbag inflates upon collision.
Page 214: Three−Way Catalytic Converter
The three−way catalytic converter is the z Use only unleaded gasoline. vehicle in for a check−up as soon emission control devices installed in as possible. Remember, your Toyota z Do not drive with an extremely low the exhaust system. dealer knows your vehicle and its fuel level;...
Page 215: Engine Exhaust Cautions
It gases to be drawn into the vehicle. Toyota Maintenance Schedule. For can cause unconsciousness or even To allow proper operation of your scheduled maintenance information, death.
Page 216: Facts About Engine Oil Consumption
(1.1 qt./600 miles, 0.9 Imp.qt/600 regularly. Toyota recommends that the oil by the high temperature combustion miles) level be checked every time you refuel gases during the combustion process.
Page 217: Iridium−Tipped Spark Plugs
In this case, the brakes may not work ity. properly. If they do not work well, depress the brake pedal firmly. If the brake system warning light comes on, immediately stop your vehicle and contact your Toyota deal- 2004 L/C100 from Aug ’03 Prod. (OM60A04U)
Page 218 The brake system warning light may stay ANTI−LOCK BRAKE SYSTEM Depressing the brake pedal on slippery on for about 60 seconds after the ignition (with “ABS” warning light) road surfaces such as on a manhole cov- key is turned to “ON” position. It is nor- er, a steel plate at a construction site, The anti−lock brake system is designed mal if the light turns off after a while.
Page 219 CAUTION Anti−lock brake system is not de- signed to shorten the stopping dis- overestimate anti−lock tance: Always drive at a moderate brake system: Although the anti−lock speed and maintain a safe distance brake system assists in providing ve- from the vehicle in front of you. hicle control, it is still important to Compared with vehicles without an drive with all due care and maintain...
Page 220 Toyota dealer. When the “ABS” warning light is on (and Have your Toyota dealer perform the bed- In this case, not only the anti−lock the brake system warning light is off), the ding−down.
Page 221: Brake Pad Wear Limit Indicators
Toyota CAUTION dealer as soon as possible. Expensive ro- tor damage can result if the pads are not Do not allow more than one person replaced when necessary. to get on the rear step bumper at a time.
Page 222: Limited−Slip Differential
This is the primary identification number Use only a spare tire of the same for your Toyota. It is used in registering size, construction and load capacity the ownership of your vehicle. as the original tires on your Toyota because damage to the limited−slip...
Page 223: Theft Prevention Labels
—Engine number Theft prevention labels Suspension and chassis Your new vehicle carries theft preven- CAUTION tion labels which are approximately 56 mm (2.20 in.) by 16 mm (0.63 in.). Do not modify the suspension/chassis The purpose of these labels is to reduce with lift kits, spacers, springs, etc.
Page 224: Tire Information
Tire information— —Tire symbols This illustration indicates typical tire symbols. 1. Tire size—For details, see “Tire size” on page 218. 2. DOT Tire Identification Number (TIN)—For details, see “DOT and Tire Identification Num- ber (TIN)” on page 217. 3. Tire ply composition and materi- als—Plies mean a layer of rubber−...
Page 225 —DOT and Tire Identification Number (TIN) 7. “TUBELESS” or “TUBE TYPE” The “DOT” symbol certifies that the —A tubeless tire does not have a tire conforms to applicable Federal tube inside the tire and air is direct- Motor Vehicle Safety Standards. ly filled in the tire.
Page 226 —Tire size —Name of each section of tire 20c506 21A007a This illustration indicates typical tire 1. Section width 1. Bead size. 2. Tire height 2. Sidewall 1. Tire (P=Passenger car, 3. Wheel diameter 3. Shoulder T=Temporary use) 4. Tread 2. Section width (in millimeters) 5.
Page 227 150 would wear conditions on specified government purchasers of Toyota vehicles with in- one and a half (1−1/2) times as well test surfaces of asphalt and concrete. formation on uniform tire quality grad-...
Page 228 Temperature A, B, C—The tempera- ture grades are A (the highest), B, and C, representing the tire’s resis- tance to the generation of heat and its ability to dissipate heat when tested under controlled conditions on a specified indoor laboratory test wheel.
Page 229 —Tire related terms Tire inflation pressure when the vehicle has been parked at least 3 hours or Cold tire inflation pressure more, or it has not been driven more than 1.5 km or 1 mile under that condition The maximum cold inflation pressure to which a tire may be inflated and shown Maximum inflation pressure on the sidewall of the tire Recommended inflation pressure...
Page 230 Vehicle capacity weight The rated cargo and luggage load plus 68 kg (150 lb.) times the vehicle’s (Total load capacity) designated seating capacity (A) The sidewall that contains a whitewall, bears white lettering or bears manufacturer, brand, and/or model name molding that is higher or deeper than the same molding on the other sidewall of the tire, or Intended outboard sidewall (B) The outward facing sidewall of an asymmetrical tire that has a particular...
Page 231 Table 1–Occupant loading and distribution for vehicle normal load for various designated seating capacities Designated seating capacity, number Vehicle normal load, number of occu- Occupant distribution in a normally of occupants pants loaded vehicle 2 through 4 2 in front 5 through 10 2 in front, 1 in second seat 2004 L/C100 from Aug ’03 Prod.
Page 232: Vehicle Load Limits
Cargo and luggage— Vehicle load limits —Stowage precautions Vehicle load limits include total load Towing capacity: When stowing cargo and luggage in capacity, seating capacity, towing ca- 2948 kg (6500 lb.) or on the vehicle, observe the follow- pacity and cargo capacity. Follow the Towing capacity means the maximum ing: load limits shown below.
Page 233 —Capacity and distribution Cargo capacity depends on the to- NOTICE D Never allow anyone to ride in tal weight of the occupants. the luggage compartment. It is Do not load the vehicle beyond (Cargo capacity) = (Total load capac- not designed for passengers. the vehicle capacity weight giv- ity) –...
Page 234 4. The resulting figure equals the 379 kg – 176 kg = 203 kg. available amount of cargo and lug- (834 lb. – 388 lb. = 446 lb.) gage load capacity. For example, As shown in the above example, if the if the “XXX”...
Page 235: Types Of Tires
Types of tires Determine what kind of tires your CAUTION vehicle is originally equipped with. Weight of removed 1. Summer tires third seat Even if the total load of occu- pant’s weight and the cargo load Summer tires are high−speed capabil- Cargo ity tires best suited to highway driving is less than the total load capac-...
Page 236 All season tires, however, do not have adequate traction performance compared with snow tires in heavy or loose snow. Also, all season tires fall short in acceleration and handling performance compared with summer tires in highway driving. The details about how to distinguish summer tires from all season tires are described on page 216.
Page 237: Starting And Driving
SECTION STARTING AND DRIVING Starting and driving Before starting the enginee ........How to start the engine .
Page 238: Before Starting The Engine
How to start the engine– (a) Cranking hold function Before starting the engine (c) Starting the engine 1. Check the area around the vehicle be- Once you turn the ignition key to “START” Before starting the engine, be sure to fol- fore entering it.
Page 239: Tips For Driving In Various Conditions
If they still do not work safely, pull to the side of the road and call a Toyota dealer for assistance. 2004 L/C100 from Aug ’03 Prod. (OM60A04U)
Page 240: Off−Road Driving Precautions
Off−road driving precautions When driving your vehicle off−road, please U.S. Forest Service and Bureau of Do not drive in excess of the speed observe the following precautions to en- Land Management limit. Even if the legal speed limit sure your driving enjoyment and to help permits it, do not drive over 140 prevent the closure of areas to off−road CAUTION...
Page 241 NOTICE z Always perform a maintenance in- After driving through tall grass, spection after each day of off−road mud, rock, sand, rivers, etc., check z If driving through water, such as driving that has taken you through that there is no grass, bush, paper, when crossing shallow...
Page 242: Winter Driving Tips
If you are not sure about accumulated in and around the parking hybrid organic acid technology. which oil to use, call your Toyota dealer– brake mechanism may freeze, making it he will be pleased to help. hard to release.
Page 243: Dinghy Towing
Ask your capacity. The combination of the local Toyota dealer for further details be- gross trailer weight added to the fore towing. total weight of the vehicle, occu-...
Page 244 Trailer hitch assemblies have differ- The load on either the front or rear ent weight capacities established by axle resulting from distribution of the hitch manufacturer. Even though the gross vehicle weight on both the vehicle may be physically capa- axles must not exceed the Gross ble of towing a higher weight, the Axle Weight Rating (GAWR) listed...
Page 245 Tongue load If you wish to install a trailer hitch, you weight in the back than in the should consult with your Toyota dealer. front. About 60% of the trailer load Use only a hitch recommended by the should be in the front half of the...
Page 246 Trailer Class Typical Trailer Ball Size NOTICE 2 in. 2 in. Do not use axle−mounted hitches as 7/8 in. they can cause damage to the axle housing, wheel bearings, wheels or 2. Select the appropriate trailer ball to tires. Also, never install a hitch which match exceed gross...
Page 247 Never tap into your vehicle’s hy- BRAKES AND SAFETY CHAINS draulic system as it would lower its Toyota recommends trailers with braking effectiveness. brakes that conform to any applica-...
Page 248 TIRES BREAK−IN SCHEDULE Ensure that your vehicle’s tires are Toyota recommends that you do not properly inflated. Adjust the tire infla- tow a trailer with a new vehicle or a tion pressure indicated below: vehicle with any new power train com-...
Page 249 Check that your rear view mirrors con- Avoid jerky starts or sudden accelera- Crosswinds and rough roads will ad- form to any applicable federal, state/ tion. versely affect handling of your vehicle provincial or local regulations. If not, and trailer, causing sway. Pay attention Avoid jerky steering and sharp turns.
Page 250 Because of the added load of the trail- When restarting out after parking on a CAUTION er, your vehicle’s engine may overheat slope: on hot days temperatures over 1. With the transmission in “P” posi- Do not exceed 72 km/h (45 mph) or 30°C [85°F]) when going up a long or tion, start the engine.
Page 251: How To Save Fuel And Make Your Vehicle Last Longer, Too
How to save fuel and make your vehicle last longer, too Improving fuel economy is easy–just take Avoid engine over-revving. Use a Keep front wheels in proper it easy. It will help make your vehicle last gear position suitable for the road on alignment.
Page 252 CAUTION Never turn off the engine to coast down hills. Your power steering and brake booster will not function with- out the engine running. Also, the emission control system operates properly only when the engine is run- ning. 2004 L/C100 from Aug ’03 Prod. (OM60A04U)
Page 253: In Case Of An Emergency
SECTION IN CASE OF AN EMERGENCY In case of an emergency If your vehicle will not startt ........If your engine stalls while driving .
Page 254: If Your Vehicle Will Not Startt
“How to start the Call a Toyota dealer or qualified repair 1. The engine may be flooded because of engine” on page 230 and that you have shop.
Page 255 If the engine still will not start, it needs which is poisonous and corrosive. adjustment or repair. Call a Toyota dealer Wear protective safety glasses when or qualified repair shop for assistance. jump starting, and avoid spilling acid on your skin, clothing, or ve- hicle.
Page 256 JUMP STARTING PROCEDURE 1. If the booster battery is installed in Discharged battery Jumper cable another vehicle, make sure the vehicles are not touching. Turn off all unneces- sary lights and accessories. Booster 2. If required, remove all the vent plugs battery from the booster and discharged batter- ies.
Page 257: If Your Engine Stalls While Driving
(for example, lights left on), will not work so steering and braking Do not connect the cable to or near you should have it checked at your Toyota will be much harder than usual. any part that moves when the engine dealer.
Page 258: If You Cannot Increase The Engine Speed
You However, note that water draining from and call a Toyota dealer for assistance: should follow this procedure... the air conditioning is normal if it has been used.
Page 259: If You Have A Flat Tire
You should have it checked as by the jack. soon as possible at your Toyota dealer. 5. Read the following instructions D Stop the vehicle on a level firm thoroughly.
Page 260 —Required tools and spare tire NOTICE D Make sure to set the jack prop- erly in the jack point. Raising Do not continue driving with a the vehicle with jack improper- deflated tire. Driving even a ly positioned will damage the short distance can damage a vehicle or may allow the ve- tire and wheel beyond repair.
Page 261 Turn the jack joint by hand. To remove the spare tire under the When connecting a jack handle exten- luggage compartment: sion with a jack handle end, use a To remove: Turn the joint in direction jack handle to tighten the bolts on the 1 until the jack is free.
Page 262 2. Remove the access hole cover on 3. Insert the jack handle end into the 4. After the tire is lowered completely the rear bumper with a flat−bladed lowering screw through the access to the ground, remove the holding screwdriver. hole and turn it counterclockwise bracket as shown in the illustration.
Page 263 —Blocking the wheel —Removing wheel ornament When storing the spare tire, put it in 2. Block the wheel diagonally op- 3. Remove the wheel ornament. place with the outer side of the wheel posite the flat tire to keep the Pry off the wheel ornament, using the facing up and hook the holding brack- vehicle from rolling when it is...
Page 264 —Loosening wheel nuts —Positioning the jack CAUTION Never use oil or grease on the bolts or nuts. The nuts may loos- en and the wheels may fall off, which could cause a serious ac- cident. 4. Loosen all the wheel nuts. Always loosen the wheel nuts before raising the vehicle.
Page 265 JACK POINTS: Front—Under the frame side rail Left rear—Under the rear axle housing Right rear—Under the bracket on the rear axle housing Make sure the jack is positioned on a level and solid place. Put a jack handle, jack handle exten- When connecting a jack handle exten- sions, and jack handle end together sion with another extension and a jack...
Page 266 —Raising your vehicle To raise the vehicle, insert the jack NOTICE handle end into the joint of the jack (it is a loose fit) and turn it clockwise Tighten all the joints securely. with the handle, making sure the han- Otherwise, the extension may dle remains firmly fitted onto the jack come off and it may damage...
Page 267 —Changing wheels —Reinstalling wheel nuts 7. Remove the wheel nuts and Before putting on wheels, remove any 8. Reinstall all the wheel nuts fin- change tires. corrosion on the mounting surfaces ger tight. with a wire brush or such. Installation Lift the flat tire straight off and put it Reinstall the wheel nuts (tapered end of wheels without good metal−to−met-...
Page 268 —Lowering your vehicle Tighten each nut a little at a time in CAUTION the order shown. Repeat the process until all the nuts are tight. D Never use oil or grease on the bolts or nuts. Doing so may CAUTION lead to overtightening the nuts and damaging the bolts.
Page 269 —Reinstalling wheel ornament —After changing wheels 11. Check the air pressure of the re- CAUTION placed tire. Adjust the air pressure to the specifi- Before driving, make sure all the cation designated on page 320. If the tools, jack and flat tire are se- pressure is lower, drive slowly to the curely in place in their storage nearest service station and fill to the...
Page 270: If Your Vehicle Becomes Stuck
If your vehicle becomes If your vehicle needs stuck to be towed— If your vehicle becomes stuck in snow, NOTICE (a) Towing with wheel lift type truck— mud, sand, etc., then you may attempt to rock the vehicle free by moving it forward If you rock your vehicle, observe the —From front and backward.
Page 271 If towing is necessary, we recommend (a) Towing with wheel lift type truck (c) Towing with sling type you have it done by your Toyota dealer Use a towing dolly under the wheels not truck or a commercial tow truck service. In lifted by the truck.
Page 272 NOTICE If towing is necessary, we recommend z Do not use front and rear eyelets. you to have it done by your Toyota It is not designed for towing. dealer or a commercial tow truck ser- vice.
Page 273 If the towing vehicle can hardly move, do not forcibly continue the towing. Contact your Toyota dealer or a commercial tow truck service for assistance. Tow the vehicle as straight ahead as possible.
Page 274: If You Cannot Shift Automatic Transmission Selector Lever
Toyota dealer if you can give them the key number and master key. Even if you lose only one key, contact your Toyota dealer to make a new key. If you lose all your master keys, you cannot make new keys; the whole engine immobi- lizer system must be replaced.
Page 275: Appearance Care
APPEARANCE CARE Corrosion prevention and appearance care Protecting your Toyota from corrosionn ..... . . Washing and waxing your Toyota .
Page 276 Now, it is up to be dry. to see all the mud and dirt. It will do you. Proper care of your Toyota can help more harm than good to simply wet the High ambient temperatures can cause ensure long−term corrosion prevention.
Page 277 Washing and waxing your Toyota Check the interior of your vehicle. Wa- Washing your Toyota 1. Rinse off loose dirt with a hose. Re- ter and dirt can accumulate under the move any mud or road salt from the Keep your vehicle clean by regular floor mats and could cause corrosion.
Page 278 4. To prevent water spots, dry the vehicle precautions. Be sure to polish and wax ing your Toyota through an automatic using a clean soft cotton towel. Do not the chrome trim as well as the paint.
Page 279: Cleaning The Interior
Cleaning the interior 3. Wax the vehicle again when water Vinyl interior CAUTION does not bead but remains on the sur- The vinyl upholstery may be easily face in large patches. cleaned with a mild soap or detergent Vehicles with side airbags and cur- and water.
Page 280 Carpets NOTICE NOTICE Use a good foam−type shampoo to z Do not use dye or bleach on the z Do not use organic substances (sol- clean the carpets. belts—it may weaken them. vents, kerosene, alcohol, gasoline, Begin by vacuuming thoroughly to remove etc.) or alkaline or acidic solutions.
Page 281 Toyota, your local cause discoloring. Toyota dealer will be pleased to answer them. z Use of a nylon brush or synthetic fiber cloth, etc. may scratch the fine grained surface of the leather. 2004 L/C100 from Aug ’03 Prod. (OM60A04U)
Page 282 2004 L/C100 from Aug ’03 Prod. (OM60A04U)
Page 283 SECTION VEHICLE MAINTENANCE AND CARE Vehicle maintenance and care Maintenance requirementss ....... . . General maintenance .
Page 284: Maintenance Requirements
See “Owner’s War- form them are presented in Section 7. or if you prefer, your Toyota dealer will be ranty Information Booklet” or “Owner’s pleased to do them at a nominal cost.
Page 285: General Maintenance
Radiator, condenser and hoses Supplement” for the details. vehicle to your Toyota dealer or a quali- Check that the front of the radiator and fied service shop immediately. It is recom- condenser are clean and not blocked with mended that any problem you notice be leaves, dirt, or insects.
Page 286 Exhaust system Seats Parking brake If you notice any change in the sound of Check that all front seat controls such as Check that the lever has the proper travel the exhaust or smell exhaust fumes, have seat adjusters, seatback recliner, etc. op- and that, on a safe incline, your vehicle the cause located and corrected immedi- erate smoothly and that all latches lock...
Page 287: Does Your Vehicle Need Repairing
If you notice any of these clues, take your tant clues are as follows: month. See page 293 for additional vehicle to your Toyota dealer as soon as information. Engine missing, stumbling, or pinging possible. It probably needs adjustment or repair.
Page 288: Emissions Inspection And Maintenance (I/M) Programs
Toyota dealer comes on. In this case, your vehicle may to prepare the vehicle for re−testing. not pass the I/M test and need to be repaired.
Page 289 SECTION − DO−IT−YOURSELF MAINTENANCE Introduction Engine compartment overview ....... Fuse locations .
Page 290: Engine Compartment Overview
Engine compartment overview 1. Engine oil filler cap 2. Brake fluid reservoir 3. Fuse block 4. Battery 5. Windshield and rear window washer fluid tank 6. Engine oil level dipstick 7. Condenser 8. Radiator 9. Engine coolant reservoir 10. Power steering fluid reservoir 2004 L/C100 from Aug ’03 Prod.
Page 291: Fuse Locations
Fuse locations Spare fuses Spare fuses 2004 L/C100 from Aug ’03 Prod. (OM60A04U)
Page 292: Do−It−Yourself Service Precautions
Read separate where you may be exposed to flying compartment—the engine, radiator, Toyota Warranty statement for details and or falling material, fluid spray, etc. exhaust manifold, power steering suggestions. Used engine oil contains potentially fluid...
Page 293: Parts And Tools
Do not overfill automatic transmis- need to perform do−it−yourself mainte- sion fluid, transfer oil and power nance. Remember all Toyota parts are de- z Remember that battery and ignition steering fluid, or the transmission, signed in metric sizes, so your tools must...
Page 294 Tools: CHECKING AND REPLACING FUSES Funnel (only for adding coolant) Parts (if replacement is necessary): CHECKING BRAKE FLUID Fuse with same amperage rating as original Parts (if level is low): ADDING WASHER FLUID SAE J1703 or FMVSS No.116 DOT 3 brake fluid Parts: Tools:...
Page 295 SECTION − DO−IT−YOURSELF MAINTENANCE Engine and Chassis Checking the engine oil level ....... . . Checking the engine coolant level .
Page 296: Checking The Engine Oil Level
Checking the engine oil level 4. Pull the dipstick out and look at the oil Low level Full level level while holding a rag under the end. CAUTION Be careful not to touch the hot ex- haust manifold. NOTICE Add oil O.K.
Page 297 ENGINE OIL SELECTION NOTICE “Toyota Genuine Motor Oil” is filled in z Be careful not to spill the engine your Toyota vehicle. Use Toyota approved oil on the vehicle components. “Toyota Genuine Motor Oil” or equivalent to satisfy the following grade and viscos-...
Page 298: Checking The Engine Coolant Level
Mark is displayed on the front of cock and water pump. Toyota engines. the container. If you can find no leak, have your Toyota Please contact your Toyota dealer for fur- dealer test the cap pressure and check ther details about “Toyota Genuine Motor for leaks in the cooling system.
Page 299: Checking The Radiator And Condenser
If any of the above parts are extremely dirty or you are not sure of their condi- Use of improper coolants may damage tion, take your vehicle to a Toyota dealer. your engine cooling system. Only use “Toyota Super Long Life Coolant”...
Page 300: Checking Brake Fluid
Checking brake fluid If the level is low, add SAE J1703 or NOTICE FMVSS No. 116 DOT 3 brake fluid to the brake reservoir. If you spill the fluid, be sure to wipe it off to prevent it from damaging the Refilling brake fluid: parts or painting.
Page 301: Checking Power Steering Fluid
Checking tire inflation pres- sure Checking power steering fluid Clean all dirt from outside of the reservoir tank and look at the fluid level. If the fluid is cold, the level should be in the “COLD” If cold range. Similarly, if it is hot, the fluid level If hot O.K.
Page 302 Keep your tire inflation pressures D Always use a tire inflation pres- Tire inflation at the proper level. sure gauge. The appearance of pressure gauge a tire can be misleading. Besides, The recommended cold tire inflation tire inflation pressures that are pressures, tire sizes and the com- even just a few pounds off can de- bined weight of occupants and cargo...
Page 303 If a tire frequently needs refilling, have it checked by your Toyota deal- 2004 L/C100 from Aug ’03 Prod. (OM60A04U)
Page 304: Checking And Replacing Tires
Checking and replacing tires The tires on your Toyota have built−in If an air loss occurs while driving, do Tread wear indicator tread wear indicators to help you not continue driving with a deflated know when the tires need replace- tire.
Page 305 Using any other size or type of tire Toyota recommends all four tires, CAUTION may seriously affect handling, ride, or at least both front or rear tires speedometer/odometer calibration, be replaced as a set. Observe the following instruc- ground clearance, and clearance be- See “If you have a flat tire”...
Page 306: Rotating Tires
To equalize tire wear and help ex- Do not use tires other than those men- tend tire life, Toyota recommends tioned above. Do not install studded tires that you rotate your tires accord- without first checking local regulations for ing to the maintenance schedule.
Page 307 SNOW TIRE INSTALLATION CAUTION Side chain Snow tires should be installed on all wheels. Observe following instructions. Installing snow tires on the rear wheels Otherwise, an accident may occur re- only can lead to an excessive difference sulting in death or serious injuries. in road grip capability between the front Do not use snow tires other than and rear tires which could cause loss of...
Page 308: Replacing Wheels
Do not use tire Correct replacement wheels are available When driving with chains installed, chains on the front tires. Retighten at your Toyota dealer. be sure to drive carefully. Slow chains after driving 0.5—1.0...
Page 309: Aluminum Wheel Precautions
1600 km (1000 miles). for a tubeless tire. When using tire chains, be careful not to damage the aluminum wheels. CAUTION Use only the Toyota wheel nuts and wrench designed for your aluminum Observe following instructions.
Page 310 2004 L/C100 from Aug ’03 Prod. (OM60A04U)
Page 311 SECTION − DO-IT-YOURSELF MAINTENANCE Electrical components Checking battery condition ........Battery recharging precautions .
Page 312: Checking Battery Condition
Checking battery condition— —Precautions —Checking battery exterior CAUTION If electrolyte gets on your skin, Ground cable Terminals thoroughly wash the contact area. If BATTERY PRECAUTIONS you feel pain or burning, get medi- cal attention immediately. The battery produces flammable and explosive hydrogen gas.
Page 313: Battery Recharging Precautions
To return the moon roof to normal, Have battery Dark White see “Electric moon roof” on page 30. checked by your NOTICE Toyota dealer. Never recharge the battery while the Clear or Have battery engine is running. Also, be sure all light checked by your accessories are turned off.
Page 314: Checking And Replacing Fuses
Checking and replacing fuses Type A fuses can be pulled out by the pull−out tool. The location of the pull−out tool is shown in the illustration. Type A If you are not sure whether the fuse has blown, try replacing the suspected fuse with one that you know is good.
Page 315: Adding Washer Fluid
Add washer gain access to the bulbs. When replacing tem. Have your Toyota dealer correct it as a bulb, make sure the ignition switch and fluid. soon as possible.
Page 316 —Headlights The inside of the lens of exterior lights Bulb Light bulbs Type such as headlights may temporarily fog up when the lens becomes wet in the rain or Rear turn signal 7440 in a car wash. This is not a problem lights because the fogging is caused by the Stop/tail lights...
Page 317 If the connector is tight, wiggle it. LEFT–HAND HEADLIGHT: Install washer inlet securely. Aiming is not necessary after replacing the bulb. When aiming adjustment is nec- essary, contact your Toyota dealer. 2004 L/C100 from Aug ’03 Prod. (OM60A04U)
Page 318 If the connector is tight, wiggle it. Aiming is not necessary after replacing the bulb. When aiming adjustment is nec- essary, contact your Toyota dealer. 2004 L/C100 from Aug ’03 Prod. (OM60A04U)
Page 319 —Front turn signal and front side marker lights —Parking lights – – Use a Phillips head screwdriver. Use a Phillips head screwdriver. 2004 L/C100 from Aug ’03 Prod. (OM60A04U)
Page 320 —Stop and tail lights Use a Phillips–head screwdriver. 2004 L/C100 from Aug ’03 Prod. (OM60A04U)
Page 321 —Rear turn signal, stop/tail, and back–up lights —License plate lights Use a flat−bladed screwdriver. a: Back–up light b: Rear turn signal light c: Stop/tail light 2004 L/C100 from Aug ’03 Prod. (OM60A04U)
Page 322 2004 L/C100 from Aug ’03 Prod. (OM60A04U)
Page 323 SECTION SPECIFICATIONS Specifications Dimensions and weightss ........Engine .
Page 324: Dimensions And Weightss
Dimensions and weights Engine Fuel Overall length mm (in.) 4890 (192.5) Model: Fuel type: 2UZ−FE Unleaded gasoline, Octane Rating 87 Overall width mm (in.) 1940 (76.4) (Research Octane Number 91) or higher. Type: ∗ 1 Overall height mm (in.) 1875 (73.8) For improved vehicle performance, the 8 cylinder V type, 4 cycle, gasoline Wheelbase...
Page 325: Service Specifications
Coolant type: DENSO SK20R11 “Toyota Super Long Life Coolant” is filled IFR6A11 in your Toyota vehicle at factory fill. In Spark plug gap, mm (in.): order to avoid technical problems, only use 1.1 (0.043) “Toyota Super Long Life Coolant” or similar high quality ethylene glycol based non−sili-...
Page 326 No.2 or Molybdenum—disulfide lithium Hypoid gear oil API GL−5 changing automatic transmission base chassis grease, NLGI No.2 fluid, use only “Toyota Genuine ATF Recommended oil viscosity: WS” (ATF JWS3324 or NWS9638) to aid Above −18_C (0_F) in assuring maximum transmission per- SAE 90 formance.
Page 327 BRAKES Minimum pedal clearance when depressed with the force of 490 N (50 kgf, 110 lbf) with the engine running, mm (in.): 116 (4.6) Pedal free play, mm (in.): 1—6 (0.04—0.24) Pad wear limit, mm (in.): 1.0 (0.04) Lining wear limit, mm (in.): 1.0 (0.04) Parking brake adjustment when pulled with the force of 196 N (20 kgf, 44 lbf):...
Page 328: Tires
Tires Tire size and inflation pressure: kPa (psi) Front Rear Tire size Wheel size Normal driving Trailer towing Normal driving Trailer towing P275/65R17 113S 200 (29) 220 (32) 220 (32) 240 (35) P275/60R18 111H 200 (29) 220 (32) 220 (32) 240 (35) Wheel nut torque, N·m (kgf·m, ft·lbf): 131 (13.4, 96.6) NOTE: For a complete information on tires (e.g.
Page 329: Fuses
Fuses Engine compartment Left side kick panel Right side kick panel Fuses 8. HAZ−TRN 15 A: 18. BAT 30 A: Emergency flashers, All components in “ECU−B2” Turn signal lights 1. ABS NO.2 40 A: Anti−lock brake sys- 19. TEL 7.5 A: No circuit 9.
Page 330 26. HEAD (LH−LWR) 10 A: Left−hand head- 42. DBL LOCK 15 A: Double lock system 63. GAUGE2 10 A: Back−up lights light (low beam) 43. BATT CHARGE 30 A 64. MET 7.5 A: Gauges and meters 27. HEAD (RH−UPR) Right−hand 44.
Page 331 SECTION REPORTING SAFETY DEFECTS FOR U.S. OWNERS AND UNIFORM TIRE QUALITY GRADING Reporting safety defects for U.S. owners and uniform tire quality grading Reporting safety defects for U.S. ownerss ....2004 L/C100 from Aug ’03 Prod.
Page 332 However, NHTSA cannot become involved in individual prob- lems between you, your dealer, or Toyota Motor Sales, U.S.A., Inc. 2004 L/C100 from Aug ’03 Prod. (OM60A04U)
Page 333 API grade, SL “Energy−Conserving” or ILSAC multigrade engine oil is recommended. See page 289 for detailed information. Automatic transmission fluid: Toyota Genuine ATF WS Tire information: See pages 293 through 301. Tire inflation pressure: See page 320. Publication No. OM60A04U Part No.
Page 334 The Toyota authorized Repair Manual is packed with literally everything you need to know to perform your own maintenance in virtually every area of your new vehicle.
Page 335 English, may be purchased as applicable from work yourself step−by−step. any Toyota dealer. Areas covered include such things as spark plug re- Pub. Name: 2004 LAND CRUISER Repair placement, valve clearance adjustment and engine oil Manual and filter replacement.

Toyota 2004 Land Cruiser Owner's Manual

1 2 Section −

1 3 Section −

1 4 Section −

1 5 Section −

1 6 Section −

1 7 Section −

1 8 Section −

1 9 Section −

1 10 Section −

2 Section

3 Section

4 Section

6 Section

7 1 Section −

7 2 Section −

Quick Links

Chapters

Related Manuals for Toyota 2004 Land Cruiser

Summary of Contents for Toyota 2004 Land Cruiser