Emerson 1F95-1277 Installation And Operating Instructions Manual page 7

INSTALLER/CONFIGURATION MENU
Table 1
Power Method
Battery Only (before thermostat installation or mV heat systems) No Backlight
Common Attached to "C" Terminal
Battery with Power Stealing on "W/E" and "Y"
Battery with "W/E" and "Y" but system does not allow Power
Stealing*
* Power Stealing Backlight Notes:
• If the sysrem is heat or cool only, or does not allow power
stealing on the thermostat terminals W/E and Y the back-
light may not operate continously or drop out when heat
or cool is running.
• If the power stealing switches (see page 2) on the back
of the thermostat are set to off the backlight will not be
continous.
will allow the thermostat to calculate the DST automatically
and apply it to the Real Time Clock display. Default is On.
18 & 19. Select Automatic Schedule – Not available if
configured for non-programmable. This feature allows
programming a "Comfort Temperature" into all program
periods with the Auto Schedule key. When Heat AS
(for Heat mode) or Cool AS (for Cool mode) is selected
On, the Auto Schedule feature is ready to be set. Off
indicates that the feature is not ready to be used or a
"Comfort Temperature" is already set. See Auto Schedule
in Programming section.
20 & 21. Select Cool Savings™ – Cool Savings™ provides an
energy saving temperature offset (from 1-6 degrees) under
peak cooling load conditions (high outdoor temperatures).
If selected on, Cool Savings™ becomes active when the
air-conditioner runs for periods of longer than 20 minutes.
When active, Cool Savings™ gradually offsets the indoor
temperature display downward. The first 1° of adjustment
will take one hour of continuous air conditioner run time
with subsequent 1° adjustments occurring with each ad-
ditional half hour of run time (ex for a 2° offset, the air con-
ditioner would need to run continuously for 1 ½ hours). The
offset is limited to the number of degrees you select from
1 up to 6. When an offset starts or is active, "Cool Savings"
will flash on the display.
The principle of this energy saving feature takes advantage
of the long air conditioning run times lowering the indoor
humidity allowing a slightly higher temperature to feel
comfortable. As the peak load subsides, this feature also
takes advantage of the air conditioner's increased capacity
under more efficient conditions to gradually reduce the off-
set back to zero and return control to the selected setpoint
temperature.
If Cool Savings is selected off, no temperature offset will occur.
22. Compressor Optimization – (Not available on earlier
models) CO provides a delay in circulator fan operation
after the compressor turns on or off. With CO selected
ON, when the compressor turns on (for a call for heat
in heat pump or a call for cool) the fan will be delayed
for five seconds before turning on to allow the air to be
heated or cooled. After the compressor turns off for call
for cool, the fan will continue to run for 20 seconds to
Power Stealing Switches ON
(Factory Default)
Backlight Option
Backlight Option
OFF
ON
(Factory Default)
Momentary Backlight
Momentary Backlight Continuous Backlight
Continuous
Momentary Backlight*
Backlight*
Momentary
No Backlight*
Backlight*
• The display light will increase in brightness when a button
is pressed.
• On high impedance systems, the display light may dim
slightly when the thermostat is calling for heat or cool.
capture additional cooling from the system. If CO is set to
OFF, there will be no delay in fan operation.
23. Comfort Alert with Active Protection – (not available
on earlier models) Turn this feature ON to enable active
protection. This allows the thermostat to identify fault
codes sent by the Comfort Alert module when compres-
sor damage is possible and react to those codes by
turning the compressor off. Fault codes from the Comfort
Alert module will flash on the thermostat. (Refer to Com-
fort Alert Codes in Troubleshooting section.) If a Comfort
Alert module is not connected, or to disable active protec-
tion, turn this feature OFF. If a Comfort Alert module is
connected and this feature is turned OFF, the thermostat
will still receive and flash the fault codes from the Comfort
Alert module, but the active protection will not be enabled
to protect the compressor.
24. Heat Temperature Limit Range – This feature adjusts
the highest setpoint temperature for heat. The default set-
ting is 99°F. It can be changed to a setting between 62°F
and 98°F. The "temperature limit" icon will be displayed
to the left of your setpoint temperature when using this
feature. The "temperature limit" icon will flash if an
attempt is made to adjust the temperature beyond the
range selected.
25. Cool Temperature Limit Range – This feature adjusts
the lowest setpoint temperature for cool. The default
setting is 45°F. It can be changed to a setting between
46°F and 82°F. The "temperature limit" icon will be dis-
played to the left of your setpoint temperature when using
this feature. The "temperature limit" icon will flash if an
attempt is made to adjust the temperature beyond the
range selected.
26 & 27. Keypad Lockout – This step allows you to select
the type of lockout or limited range security required. If no
lockout or limited range security is required, press
advance the menu.
Three security settings are available in this menu item.
Use the
Lockout selections are:
"Keypad Lockout and L" = Total Lockout. Total Lockout
locks all keys.
"Keypad Lockout and P" = Partial Lockout. Partial Lock-
Power Stealing Switches ON
(Factory Default)
Backlight Option
OFF
(Factory Default)
No Backlight
Momentary Backlight
No Backlight
No Backlight
or keys to select the lockout desired.
Backlight Option
ON
Momentary
Backlight
Continuous Backlight
Momentary
Backlight
Momentary
Backlight
to
7