Detailed Specifications - Harman Kardon AVR7000 Preliminary Service Manual

DETAILED SPECIFICATION FOR RECEIVER AVR7000 (120V)
PARAMETERS
Measuring methods are based on IHF and IEC standard 268-3
Measurement conditions,unless otherwise noted :
Output resistive load =
Tone Off or Tone(Bass,Treble), Balance, EQ control : Center Position , Other SW's : OFF, Volume:Max
Nominal input level : 200mV for general purpose inputs
Power figures should be kept minimum 10min., between 15 and 35
Terminator : 1kohm for general purpose inputs
All Voltage Measurements are made with RMS detector, unless otherwise specified.
Filter : IHF-A filter
R/O = Rated Output, which is 100 W into 8 ohm resistive load, for both Stereo and 6 CH DIRECT inputs.
UUT= Unit Under Test.
Power supply : 120 V , 60 Hz
D
FRONT AMP SECTION
NO DESCRIPTION Y/N
1
INPUT SENSITIVITY
2 CHANNEL BALANCE
3
DAMPING FACTOR
4
HICC
5 RESIDUAL NOISE
RESIDUAL NOISE
6
TOTAL HARMONIC
DISTORTION
TOTAL HARMONIC
DISTORTION
TOTAL HARMONIC
DISTORTION
TOTAL HARMONIC
DISTORTION
7 CONTINUOUS AVERAGE
POWER: A) Stereo, 8
Ohm load, Fl and FR driven.
(8) ohms / All channels loaded.
o .
C
*SUB-WOOFER SPKR:NO *SPKR LEVEL:ALL 0dB
INPUT FREQ.
Y CD
Y 6 CH DIRECT
6 CH DIRECT
Y
Y
Y 6 CH DIRECT
Y 6 CH DIRECT 10 KHz
Should be met
Y by all Stereo
Inputs
Should be met
Y by all Stereo
Inputs
Should be met
Y by all Stereo
Inputs
Should be met
Y by all Stereo
Inputs
Should be met
Y by all Stereo
Inputs
Y 6 CH DIRECT
Y 6 CH DIRECT
Y 6 CH DIRECT
Y 6 CH DIRECT
Y 6 CH DIRECT
Should be met 20Hz-20 KHz, Power
Y by all Stereo out =Rated Power - 1
Inputs dB
20Hz-20 KHz, Power
Y 6 CH DIRECT out =Rated Power - 1
dB
Should be met
20Hz-10 KHz, Power
Y by all Stereo
out =1 W
Inputs
20Hz-10 KHz, Power
Y 6 CH DIRECT
out =1 W
Y CD
Y CD
REMARK
1kHz To obtain rated Power
1kHz To obtain rated Power
1kHz
Vin=100mV, Vol at Max TO -40dB
1kHz Vin=100mV, Volt at -40 TO -60dB
Zout at a current level equivalent to 10
1kHz dB below rated Power current level. 20-
20kHz, 8 ohm load
10 KHz single cycle sine impulse. 1
impulse/sec. Using 0.1 ohm, 1%, 250
W, non inductive load
VOL at min. 10Hz-22KHz BW, peak
1kHz detector, all inputs terminated w/ 1
Kohm
VOL at max. 10Hz-22KHz BW, peak
1kHz detector, all inputs terminated w/ 1
Kohm
VOL at max. 10Hz-22KHz BW, RMS ,
1kHz non-weighted, all inputs terminated w/
1 Kohm
VOL at max. 10Hz-22KHz BW, RMS ,
1kHz 'A Weighted', all inputs terminated w/ 1
Kohm
VOL at max. 10Hz-22KHz BW, RMS ,
1kHz 'A Weighted', all inputs left un-
terminated
VOL at min. 10Hz-22KHz BW, peak
1kHz detector, all inputs terminated w/ 1
Kohm
VOL at max. 10Hz-22KHz BW, peak
1kHz detector, all inputs terminated w/ 1
Kohm
VOL at max. 10Hz-22KHz BW, RMS,
1kHz non-weighted, all inputs terminated w/
1 Kohm
VOL at max. 10Hz-22KHz BW, RMS,
1kHz 'A Weighted', all inputs terminated w/ 1
Kohm
VOL at max. 10Hz-22KHz BW, RMS,
1kHz 'A Weighted', all inputs left un-
terminated
Vol at Max, 10 Hz-80KHz Meas BW.
Vol at Max, 10 Hz-80KHz Meas BW.
Vol at Max, 10 Hz-22 KHz Meas BW.
Vol at Max, 10 Hz-22 KHz Meas BW.
at 0.1% THD, 10 Hz-80 KHz
20 Hz
measurement BW. Volume at Max.
at 0.1% THD, 10 Hz-80 KHz
1kHz
measurement BW. Volume at Max.
UNIT LIMIT NOMINAL
mV 200+/-30 200+/-20
mV
dB +/-3 +/-2
dB +/-6 +/-4
>100
A >60 >65
mVpk <1.2mV <1.0mV
mVpk <3mVrms <1.5mVrms
mVrms <1mVrms <0.75mVrms
mVrms <0.7mVrms
<0.5mVrms
mVrms <0.7mVrms <0.5mVrms
mVpk <1.2mVrms <1.0mVrms
mVpk <3mVrms
<1.5mVrms
mVrms <1mVrms
<0.75mVrms
mVrms <0.7mVrms <0.5mVrms
mVrms
<0.7mVrms <0.5mVrms
% <0.08 <0.05
% <0.08
<0.05
% <0.08 <0.05
% <0.08
<0.05
W >110 >115
W >110 >115
5