TP-Link T1700G-28TQ Installation Manual
Jetstream 24-port gigabit stackable
smart switch with 4 10ge sfp+ slots
Hide thumbs
Also See for T1700G-28TQ:
- User manual (258 pages) ,
- Installation manual (24 pages) ,
- Installation manual (24 pages)
Related Manuals for TP-Link T1700G-28TQ
Summary of Contents for TP-Link T1700G-28TQ
- Page 1 Business Networking Solution Installation Guide JetStream 24-Port Gigabit Stackable Smart Switch with 4 10GE SFP+ Slots T1700G-28TQ...
-
Page 3: Fcc Statement
Specifications are subject to change without notice. is a registered trademark of TP-LINK TECHNOLOGIES CO., LTD. Other brands and product names are trademarks of their respective holders. No part of the specifications may be reproduced in any form or by any means or used to make any derivative such as translation, transformation, or adaptation without permission from TP-LINK TECHNOLOGIES CO., LTD. - Page 4 The User Guide and CLI Reference Guide of the product are provided on the resource CD. To obtain the latest product information, please visit the official website: http://www.tp-link.com About this Installation Guide This Installation Guide describes the hardware characteristics, installation methods and the points that should be attended to during installation.
-
Page 5: Table Of Contents
Contents Chapter 1 Introduction ———————————— 01 Product Overview ........01 Appearance ........... 0 Chapter 2 Installation ———————————— 04 Package Contents ........04 Safety Precautions ........04 Installation Tools ........06 Product Installation ........07 Stacking Using SFP+ Port ......08 Chapter 3 Lightning Protection ———————— 10 Cabling Reasonably ........10 Connect to Ground ........12 Equipotential Bonding .......13... -
Page 6: Chapter 1 Introduction
T1700G-28TQ also supports stacking of up to 6 units, thus providing flexible scalability and protective redundancy for your networks. - Page 7 Designed to connect to the device with a bandwidth of 10Mbps, 100Mbps or 1000Mbps. Each has a corresponding Link/Act LED and a 1000Mbps LED. SFP+ Port Port 25-28, designed to install the 1Gbps SFP transceiver, 10Gbps SFP+ transceiver or SFP+ cable. Port Feature Model 10/100/1000Mbps RJ45 Port SFP+ Port T1700G-28TQ Introduction...
-
Page 8: Rear Panel
JetStream Gigabit Stackable Smart Switch Rear Panel ■ The rear panel of T1700G-28TQ features a Kensington security slot, a grounding terminal and a power socket. Power Socket Grounding Terminal Kensington Security Slot Figure 1-2 Rear Panel Kensington Security Slot Secure the lock (not provided) into the security slot to prevent the device from being stolen. -
Page 9: Chapter 2 Installation
JetStream Gigabit Stackable Smart Switch Chapter 2 Installation Package Contents Make sure that the package contains the following items. If any of the listed items is damaged or missing, please contact your distributor. This Installation Guide One Switch One Power Cord Two Mounting Brackets and the One Resource CD Fittings... -
Page 10: Site Requirements
JetStream Gigabit Stackable Smart Switch Site Requirements ■ Temperature/Humidity Please keep a proper temperature and humidity in the equipment room. Too high/low humidity may lead to bad insulation, electricity leakage, mechanical property changes and corrosions. Too high temperature may accelerate aging of the insulation materials and can thus significantly shorten the service life of the device. -
Page 11: Installation Tools
JetStream Gigabit Stackable Smart Switch Lightning Protection Extremely high voltage currents can be produced instantly when lightning occurs and the air in the electric discharge path can be instantly heated up to 20,000℃. As this instant current is strong enough to damage electronic devices, more effective lightning protection measures should be taken. -
Page 12: Product Installation
JetStream Gigabit Stackable Smart Switch 2.4 Product Installation Desktop Installation ■ To install the device on the desktop, please follow the steps: 1. Set the device on a flat surface strong enough to support the entire weight of the device with all fittings. 2. -
Page 13: Stacking Using Sfp+ Port
2. Power off the switches, and then use the 10G SFP+ cable (TXC432-CU1M/TXC432- CU3M of TP-LINK for example) to connect each switch to the next in a cascade. Finally, connect the last switch in the stack to the first switch, thus forming a ring topology as Figure 2-4 shows. - Page 14 For more information about stack topology and master election, please refer to "Stack" chapter in the User Guide on the Resource CD. Caution: In the process of using TP-LINK SFP+ Cables, please never bend them into a radius of 45mm (1.77 inch) or less, because it may permanently damage the SFP+ Cables.
-
Page 15: Chapter 3 Lightning Protection
JetStream Gigabit Stackable Smart Switch Chapter 3 Lightning Protection Cabling Reasonably In the actual network environment, you may need cable outdoors and indoors, and the requirements for cabling outdoors and indoors are different. A reasonable cabling system can decrease the damage of induced lightning to devices. Note: It's not recommended using Ethernet cables outdoors. -
Page 16: Requirements For Cabling Indoors
JetStream Gigabit Stackable Smart Switch Requirements for Cabling Indoors ■ When cabling indoors, keep a certain distance away from the devices that may cause high-frequency interferences, such as down-conductor cable, powerline, power transformer and electromotor. The main cable should be paved in the metal raceway of the access shaft. When ■... -
Page 17: Connect To Ground
JetStream Gigabit Stackable Smart Switch Min Parallel Cable Pave Way Length (mm) Parallel cabling 2-5kVA One is in the grounded metal raceway or metal pipe powerline The both are in the grounded metal raceway or metal pipe Parallel cabling >5kVA One is in the grounded metal raceway or metal pipe powerline The both are in the grounded metal raceway or metal... -
Page 18: Equipotential Bonding
JetStream Gigabit Stackable Smart Switch Note: The grounding bar and the ground cable are not provided with our product. If needed, please self purchase them. Connecting to the Ground via the Power Supply ■ If the device is installed in the normal environment, the device can be grounded via the PE (Protecting Earth) cable of the AC power supply as shown in the following figure. -
Page 19: Use Lightning Arrester
JetStream Gigabit Stackable Smart Switch Grounding Terminal Equipotential Bonding Cable Ground Cable Grounding Bar Figure 3-3 Equipotential Bonding When equipotential bonding, please note that the cable should be copper conductor with a sectional area of 6mm at least, wrapped green with yellow stripe. The shorter cable the better, and use a grounding bar to establish an equipotential bonding point. - Page 20 JetStream Gigabit Stackable Smart Switch When purchasing or using a signal lightning arrester, please observe the following rules: The port rate of the signal lightning arrester should match the rate of the desired ■ port on the device. If it is not matched, this signal lighting arrester will not work. Purchase a standard lightning arrester.
-
Page 21: Chapter 4 Connection
JetStream Gigabit Stackable Smart Switch Chapter 4 Connection Ethernet Port Connect an Ethernet port of the switch to the computer by RJ45 cable as the following figure shows. RJ45 Port RJ45 Cable Figure 4-1 Connecting the RJ45 Port 4.2 SFP+ Port Connect an SFP/SFP+ transceiver or an SFP+ cable to the SFP+ port. -
Page 22: Power On
JetStream Gigabit Stackable Smart Switch The voltage of the power supply meets the requirement of the input voltage of the device. ■ The power socket, device and rack are well grounded. ■ The device is correctly connected to other network devices. ■... -
Page 23: Chapter 5 Configuration
JetStream Gigabit Stackable Smart Switch Chapter 5 Configuration Confi gure the Switch via GUI 1. To access the GUI of the switch, open a web browser and type the default management address http://192.168.0.1 in the address field of the browser, then press the Enter key. -
Page 24: Configure The Switch Using Cli
JetStream Gigabit Stackable Smart Switch 3. After a successful login, the main page will appear as the following figure, and you can configure the function by clicking the setup menu on the left side of the screen. Figure 5-3 Main Page of the Switch 5.2 Configure the Switch Using CLI You can log on to the switch and access the CLI by Logging on to the switch remotely by a Telnet connection through an Ethernet port. - Page 25 JetStream Gigabit Stackable Smart Switch 3. Type telnet 192.168.0.1 in the command prompt shown as Figure 5-5, and press the Enter button. Figure 5-5 Connecting to the Switch 4. Type the default user name and password (both of them are admin), then press the Enter button so as to enter User EXEC Mode.
-
Page 26: Appendix A Troubleshooting
JetStream Gigabit Stackable Smart Switch Appendix A Troubleshooting Q1. What could I do if I forgot the username and password of the switch? Press the Reset button for at least 5 seconds to reset the system. The system will be reset to the factory default settings, and the default login user name and password are both admin. -
Page 27: Appendix B Hardware Specifications
JetStream Gigabit Stackable Smart Switch Appendix B Hardware Specifications Item Content IEEE 802.3 10Base-T Ethernet IEEE 802.3u 100Base-TX/100Base-FX IEEE 802.3ab 1000Base-T Standards IEEE 802.3z 1000Base-X IEEE 802.3x Flow Control 10Base-T: UTP/STP of Cat. 3 or above (maximum 100m) 100Base-TX: 2-pair UTP/STP of Cat. 5 or above (maximum 100m) 1000Base-T: 4-pair UTP/STP of Cat. - Page 28 Website: http://www.tp-link.com E-mail: support@tp-link.com 7106505535 REV1.0.0...