Sony STR-DA5200ES Service Manual page 26

STR-DA5200ES
QQ
3 7 63 1515 0
SPECIAL MENU MODE
Procedure:
1. Press the [POWER] button to turn on the main power, then while pressing the [TONE MODE] button, press the [A.F.D.], [2CH], [MUSIC],
[MOVIE] button in order.
2. The message "MENU SPECIALIZED!" appears.
3. Each time the button of the remote commander is pressed, the item is switched in order as follows.
M m
4. To release from this mode, while pressing the [TONE MODE] button, press the [A.F.D.], [2CH], [MUSIC], [MOVIE] button in order again.
5. The message "MENU SPECIALIZED OFF" appears.
Items
RAM watch menu
Protector on/off
Model version display
Model/destination change
Video Ucom version display
FAROUDJA version display
USB Ucom version display
USB LIB version display
XM TUNER version display
FM/AM tuner version display
Auto cal mic test
FL display fonts test
TE
L 13942296513
FL display test
Audio swap
Video factory menu
Video calibration
(Video factory menu)
www
DDR access check
(Video factory menu)
DSP halt
.
DSP RAM
26
http://www.xiaoyu163.com
Display
XXX
PROTECTOR ON/OFF [XXX]
##### *** vX. XX @@@@
MODEL [##### * * * *] X X
Video Ucom Ver X. XX
FAROUDJA Ver X. XX
USB Ucom Ver X. XX
USB LIB Ver X. XX
XM Tuner Ver X. XX
FM/AM Tuner Ver X. XX
SPEAKER OUT [XXXXX]
FL FONT 0x ** = [X]
ALL ON
SWAP [XXXXXXXXXXX]
<VIDEO FACTORY MENU>
V.CAL START? N:#, P:@
Please Check V.Input
DDR CHECK [XXX]
x ao u163
y
DSP HALT [XXX]
i
[*****]=XXXXXXXX
http://www.xiaoyu163.com
2 9
8
Remark
XXX: For monitor of various internal RAM (for design evaluation)
XXX: ON or OFF
(switching with button of the remote commander)
M m
#####: model
***: destination
X.XX: system controller software version
@@@@: Sum value of flash memory in the main system controller
#####: model, ****: destination, XX: at or fx
(switching with button of the remote commander)
M m
X.XX: Video Ucom software version
X.XX: FAROUDJA (Video Processor) software version
X.XX: USB Ucom controller software version
X.XX: USB function control library version
X.XX: XM tuner controller software version
X.XX: FM/AM tuner controller software version
XXXXX: Selection of speaker output audio
[SOURCE]: nomally mode, [MIC]: mode that output audio from mic from
speaker
**: 20 to FE, X: character (switching with
Q Q
commander) 3 6 7 1 3 1 5
Each time DISPLAY button to change as follows.
all on → test pattern 1 → test pattern 2 → all off → all on
Switching with button of the remote commander
M m
Menu mode to enter video calibration menu and DDR access check menu
If the [ENTER] button of the remote commander is pressed, entering the
menu, and operating two the following menu become possible
Procedure:
1. "DVD" is selected.
2. Connect a color pattern generator to the EXT VIDEO VIDEO IN jack
(J6905) on the S-VIDEO board, DVD S VIDEO IN jack (J6902) on the S-
VIDEO board, COMPONENT VIDEO DVD IN jack (J6102) on the VIDEO
board and DVD VIDEO IN jack (J6401) on the VIDEO board.
3. Input 100% color bars signal from the color pattern generator.
Menu that measures individual difference of hardness by automatic operation
in pressing the [ENTER] button of the remote commander, and corrects
reference value.
In a measurement once, only one of NTSC/PAL can be measured
"V.CAL START?" at display
#: X (NTSC measurement incompletion) or O (NTSC measurement completion)
@: X (PAL measurement incompletion) or O (PAL measurement completion)
"Please Check V.Input" at display
Video signal necessary for the measurement while measuring it last time was
not detected and it became an error
Confirm the input of the video of the terminal connection etc. , and measure
the [ENTER] button of the remote commander again pressing
XXX: Time to do access check on DDR (for design evaluation)
co
XXX: ON or OFF (switching with
.
Mode not to send DSP host code, and to make only decipherment done
Mode that refers to internal RAM of DSP (for design evaluation)
9 4 2 8
button of the remote
M m
0 5 8 2 9 9 4 2 8
m
button of the remote commander)
M m
9 9
9 9