Servicing Notes - Sony STR-DA5200ES Service Manual

Multi channel av receiver
Hide thumbs Also See for STR-DA5200ES:
Table of Contents

Advertisement

QQ
3 7 63 1515 0
• MODEL IDENTIFICATION
– Back Panel –
Model
US and Canadian models
AEP model
UK model
NOTE OF REPLACING THE IC3509 AND IC3513 ON
THE HDMI BOARD
When IC3509 and IC3513 on the HDMI board are damaged,
exchange the new HDMI board for the HDMI board which IC
damaged. When throwing away the HDMI board, be sure to throw
away after destroying IC3509 and IC3513 physically with the
hammer etc.
COLOR VARIATION
Destination
BLACK
US, Canadian
AEP, UK
TE
L 13942296513
UPDATE OF SOFTWARE OF THE SYSTEM CONTROLLER (IC2054)/HDMI CONTROLLER (IC3610)/
USB CONTROLLER (IC006)
Perform operation of the following when the update of software of the system controller (IC2054)/HDMI controller (IC3610)/USB controller
(IC006) is necessary.
Connect:
Procedure:
1. Turn off the main power and setting the jig referring to Fig. 1 (Note: Do this setting before connecting jig with the set).
2. Remove the KNOB (VOL) ASSY and connect CN713 (M-VOLA3 board) and PC by using the jig.
3. Turn on the main power and perform the operation according to the application.
4. After "Please Reset" is displayed, reset switch on the jig is pushed and update is completed.
5. Turn off the main power and remove the jig.
6. Turn on the main power.
www
When system controller (IC2054) is updated
(RESET)
.
SW2 SW1
SW1: up, SW2: down
http://www.xiaoyu163.com

SERVICING NOTES

PART No.
PART No.
2-668-097-7[]
2-668-097-8[]
2-668-097-9[]
COLOR
SILVER
z
z
z
JIG
for PC
(Part No. : J-2501-300-A)
When HDMI controller (IC3610) is updated
x
ao
y
(RESET)
i
SW1: up, SW2: up
http://www.xiaoyu163.com
SECTION 1
8
UNLEADED SOLDER
Boards requiring use of unleaded solder are printed with the lead-
free mark (LF) indicating the solder contains no lead.
(Caution: Some printed circuit boards may not come printed with
the lead free mark due to their particular size)
: LEAD FREE MARK
Unleaded solder has the following characteristics.
• Unleaded solder melts at a temperature about 40 °C higher
than ordinary solder.
Ordinary soldering irons can be used but the iron tip has to be
applied to the solder joint for a slightly longer time.
Soldering irons using a temperature regulator should be set to
about 350 °C.
Caution: The printed pattern (copper foil) may peel away if
• Strong viscosity
Unleaded solder is more viscou-s (sticky, less prone to flow)
than ordinary solder so use caution not to let solder bridges
occur such as on IC pins, etc.
• Usable with ordinary solder
It is best to use only unleaded solder but unleaded solder may
also be added to ordinary solder.
NOTE THE IC3601 ON THE HDMI BOARD AND
IC084 ON THE USB BOARD REPLACING
Replacement of IC3601 on the HDMI board and IC084 on the USB
board used in this set requires a special tool.
Q Q
3
6 7
1 3
Fig.1 Setting for jig
u163
.
SW2 SW1
STR-DA5200ES
2 9
9 4
2 8
the heated tip is applied for too long, so be careful!
1 5
0 5
8
2 9
9 4
M-VOLA3 board
CN713
m
When USB controller (IC006) is updated
co
(RESET)
SW2 SW1
SW1: down, SW2: up
9 9
2 8
9 9
5

Advertisement

Table of Contents
loading

Table of Contents