Preparation For Use - Electrohome WELLINGTON EANOS502 Instruction Manual

BUTTONS AND CONNECTIONS
1. Phonograph Lid
Lift to reveal turntable
2. Phonograph Lid Support Stand
Lift and clip into place to hold
up lid
3. Speakers
4. FM Dial Scale
Indicates the FM channels
5. FM Stereo Indicator
Indicates FM stereo is ON
6. Tuning Control
Indicates which station is
being played
7. Random Button
Shuffle and play songs randomly
8. Repeat Button
Repeat 1 or all songs on a CD
9. AM-FM-CD-PH-AUX Function Switch
Changes the player function
10. Program Button
Program a set of songs to play
11. USB Connection
12. Play/Pause Button
Plays/Pauses playback
13. Stop Button
Stops playback
14. Skip Reverse Button
Skip back one track
15. AM Dial Scale
Shows the AM stations
16. CD Track Display
Displays the track currently being played
17. Record Button
Record CD to USB or Album to USB
18. Folder+/+10
19. Volume Control
Control the volume of playback
20. Folder–/–10
21. Headphone Jack
Plug your headphones in here
22. Open/Close Button
Opens and closes the CD tray
23. Skip Forward Button
Skip to next track
24. CD Disc Tray
Holds the CD in the unit
25. Service Sticker
Allows access to adjustment screw
26. AUX IN Input
Connect your MP3 player
or smartphone to play to music
27. ON/OFF Switch
Turns power ON and OFF
28. FM Antenna Wire
Improves FM reception
29. AC Power Cord
Plug AC power cord into any wall outlet
30. Turntable
Place vinyl record here
31. 45 RPM Adapter
Place in centre of turntable to accomodate 45 RPM
records
32. Transit Screw
Tighten during transportation
33. Cue Lever
Raise or lower tone arm
34. Speed Selector (33/45/78 RPM)
Select speed record should be played at
35. Tone Arm Lock
Locks stylus arm
36. Tone Arm with Stylus
Plays records
37. Open/Close Button
Opens and closes the CD tray
38. Repeat Button
Repeat 1 or all songs on a CD
39. DN/FB (Skip Reverse)
Skip back one track
40. Stop Button
Stops playback
41. Track -10
42. Random Button
Shuffle and play songs randomly
43. Record Button
44. Play/Pause Button
Plays/Pauses playback
45. UP/FF (Skip Forward)
Skip to next track
46. Track +10
47. Delete Button
48. Program Button
Program a set of songs to play
NOTE: All of the buttons on the remote control have
the same function as the buttons on the main unit.
- 6 -

PREPARATION FOR USE

PREPARATION FOR USE
UNPACKING AND SETUP
• Carefully remove the unit from the display carton
and remove all packing material from the unit
• Unwind the AC power cord and extend it to its full
length
• Unwind the FM Antenna wire and extend it to its
full length
• Place the unit on a stable, level surface, close to
an AC outlet, out of direct sunlight, and away from
sources of excess heat, dust, moisture, humidity, or
strong magnetic fields
• Raise the lid to expose the phonograph. The phonograph has been secured for shipment with a transit
screw. Use a coin or screwdriver to TURN THE TRANSIT SCREW CLOCKWISE. This will allow the turntable
to "float" and turn freely.
• Remove the opaque white plastic stylus cover from the
phonograph stylus by sliding it in the direction of the arrow.
• Discard the stylus cover.
• Remove the twist-tie that was used to secure the tone
arm during shipment.
• Release the tone arm lock lever.
• Connect the plug to your AC outlet, as shown below.
POWER SOURCE
This system is designed to operate on normal 120V
60Hz AC only. Attempting to operate this system
from any other power source may cause damage to
the system, and such damage is not covered by
your warranty.
Note: This system is equipped with a polarized
AC power plug having one blade wider than the
other. This is a safety feature. If this plug does not
fit into your existing AC outlet, do not try to defeat
this safety feature by altering the wide blade to
make it fit into your outlet. If this plug will not fit
into your outlet, you probably have an outdated
non-polarized AC outlet. Have the obsolete outlet
changed by a qualified licensed electrician.
Transit Screw
Stylus
Tone Arm
Cover Lock Lever
BATTERY INSTALLATION OF REMOTE CONTROL
• The remote control requires one CR2025 (3V)
lithium battery.
• Hold level pressing the clasp with the
thumb in the right direction of the arrow
in the illustration, and take out the battery
compartment by sliding with forefinger in
the direction to yourself. Take out the battery
compartment from the remote control.
Install a lithium battery (CR-2025) in the
compartment with the positive polarity
turned up. Hold level and push the battery
compartment into the remote control lightly.
It is okay once you hear a click.
- 7 -