Download Print this page

Advertisement

SERVICE MANUAL
The PDP panel made from FHP is used for this product.
Be sure to read this manual before servicing. To assure safety from fi re, electric shock, injury, harmful
radiation and materials, various measures are provided in this HITACHI display.
Be sure to read cautionary items described in the manual to maintain safety before servicing.
1. Since Panel Module and front Filter are made of glass, handling the broken Module and Filter shall be
taken care suffi ciently in order not to be injured.
2. Replacing work shall be started after the Panel Module and the AC/DC Power supply become suffi -
ciently cool.
3. Special care shall be taken to the display area in order not to damage its surface.
4. The Panel Module shall not be touched with bare hand to protect its surface from stains.
5. It is recommended to use clean soft gloves during the replacing work in order to protect not only the
display area of the Panel Module but also a serviceman himself.
6. The Chip Tube of Panel Module (located upper left of the back and surrounded by frame) and fl exible
cables connecting Panel glasses to drive circuit PWBs are very weak, so shall be taken care suffi -
ciently not to break. If you break Chip Tube, the Panel doesn't display anything forever.
1. Features ----------------------------------------------- 3
2. Specifi cations ----------------------------------------- 4
3. Service point ------------------------------------------ 5
4. Component names ---------------------------------- 6
5. New adoption technology -------------------------- 8
6. Adjustment ------------------------------------------ 12
7. Troubleshooting ------------------------------------ 28
8. Self-diagnosis function --------------------------- 32
SPECIFICATIONS AND PARTS ARE SUBJECT TO CHANGE FOR IMPROVEMENT.
Caution

Service Warning

Contents
9. Basic circuit diagram ------------------------------ 35
10.Printed wiring board diagram ------------------- 57
11.Block diagram -------------------------------------- 62
12.Connection diagram ------------------------------ 63
13.Wiring diagram ------------------------------------- 64
14.Disassembly diagram ---------------------------- 66
15.

Plasma Display

December 2006
No.040E
YK
50PD9800TA(FW1)
----------------------------- 71

Advertisement

   Also See for Hitachi 50PD9800TA

   Related Manuals for Hitachi 50PD9800TA

   Summary of Contents for Hitachi 50PD9800TA

  • Page 1: Table Of Contents

    Be sure to read this manual before servicing. To assure safety from fi re, electric shock, injury, harmful radiation and materials, various measures are provided in this HITACHI display. Be sure to read cautionary items described in the manual to maintain safety before servicing.

  • Page 2

    50PD9800TA (FW1) CAUTION FOR SAFETY Please read this page before repair the monitor. This page explains to following items for keep the safety of set and prevent to accident during repair work. We explain by symbol at happen the damage or injury when took wrong repair.

  • Page 3: Features

    50PD9800TA (FW1) PRECAUTIONS How to clean the plasma screen panel of the monitor Before cleaning the monitor, turn off the monitor and disconnect the power plug from the power outlet. To prevent scratching or damaging the plasma screen face, do not knock or rub the surface with sharp or hard objects.

  • Page 4: Specifi Cations

    50PD9800TA (FW1) 2. Specifications Display dimensions Approx. 50 inches (1106(H) x 626(V)mm, diagonal 1270mm) Panel Resolution 1280(H) x 1080(V) pixels including Optional Stand : 1240(W) x 900(H) x 423(D)mm Net dimensions excluding Optional Stand : 1240(W) x 836(H) x 125(D)mm including Opional Stand : 46.5kg...

  • Page 5: Service Point

    50PD9800TA (FW1) 3. Service points Lead free solder This product uses lead free solder (unleaded) to help preserve the environment. Please read these instructions before attempting any soldering work. Caution: Always wear safety glasses to prevent fumes or molten solder from getting into the eyes. Lead free solder can splatter at high temperatures (600˚C).

  • Page 6: Component Names

    50PD9800TA (FW1) 4. Component names [Main unit] COMPONENT NAMES Main Unit Front Panel q Cabinet w Panel e Remote Control Receiver r Indicating Lamp t Main Power Switch (on the bottom surface) y Control Panel and Front Input (see below for details)

  • Page 7: Remote Control

    50PD9800TA (FW1) [Remote control] q Sub Power w Function Select (TV/DVD/STB) indicating LED lamp. Normally, select “TV”. e Input Select/DVD Control Press this button to change input mode. e l i operating the selected brand of DVD player. r Menu...

  • Page 8: New Adoption Technology

    50PD9800TA (FW1) 5. New adoption technology [System control micom I001(M30627)] Pin function table Pin Name FUNCTION 1 VREF (+5.0V) 2 +5.0V 3 M_SW1 I/O Main SW1 4 M_SW2 I/O Main SW2 5 S_SW1 I/O Sub SW1 6 BL_CONT I/O LCD Backlight control (DA-out)

  • Page 9

    50PD9800TA (FW1) Pin Name FUNCTION 51 CPUGO(PM_CPU) I/O PDP control / Inverter (V) 52 EPM (FLASH) I/O FLASH write 53 DISPEN I/O DISPEN / Backlight on 54 SCL1 I/O I2C(to Sub PWB) FE/MSP4450G or MSPxxxxG 55 SDA1 I/O I2C(to Sub PWB) FE/MSP4450G or MSPxxxxG...

  • Page 10

    50PD9800TA (FW1) Pin Name FUNCTION 101 FC6_XRST I/O FC6 XRST 102 SCL0 I/O I2C (for Main PWB & Sub PWB)(SAA7117A/AN15867A/MM1631/MAX9723DETE) 103 SDA0 I/O I2C (for Main PWB & Sub PWB)(SAA7117A/AN15867A/MM1631/MAX9723DETE) 104 SCL3(EEPROM) I/O I2C(EEPROM) 105 SDA3(EEPROM) I/O I2C(EEPROM) 106 EPGGO...

  • Page 11

    50PD9800TA (FW1) Block diagram...

  • Page 12: Adjustment

    50PD9800TA (FW1) 6. Adjustment ● How to get to Adjustment mode Using the front buttons with the set turned off (standby) can activate it. Press the SUB-POWER( ) button, and MENU button at the same time, and hold for more than 5 seconds.

  • Page 13

    50PD9800TA (FW1) Service adjustment items by I C-bus control (MAIN Part) Max. Init. Device Value Value Sub Composite mode 0 SUB_CONTRAST (AV1) DCON[7:0] SAA7117 Sub Composite mode 1 SUB_CONTRAST (AV2) DCON[7:0] SAA7117 Sub Composite mode 2 SUB_CONTRAST (AV3) DCON[7:0] SAA7117A...

  • Page 14

    50PD9800TA (FW1) Max. Init. Adj. Function Device ADJ. Items Mode Value Value 78 RTS Output Control polarity RTP0 SAA7117A 79 RTS SAA7117A Output Control RTSE1[3:0] 80 RTS Output Control RTSE0[3:0] SAA7117A 81 Limit Level Image Port ILLV[1:0] SAA7117A 82 Dynamic Back Light 0:OFF, 1:ON (LCD only)

  • Page 15

    50PD9800TA (FW1) Max. Init. Device Value Value 001BH ADM7(Temperature detection value) 001CH 157 ADM8(Temperature detection value) 005EH 158 ADM9(Temperature detection value) only for A4SF Pane 159 ADM10(Temperature detection value) only for A4SF Pane 005FH 001EH 160 MAXAVE (Maximum mean value of ADM)

  • Page 16

    50PD9800TA (FW1) Max. Init. Device Value Value 231 CONFIGURATION SOURCE SELECTION CONLV SAA7117A 232 CONFIGURATION SOURCE SELECTION HLDFV SAA7117A 233 LOUD MAIN (for BBE=LOW , Truebase=OFF) MSP4450G 234 LOUD MAIN (for BBE=HIGH, Truebase=OFF) MSP4450G 235 BASS OFST (for BBE=LOW , Truebase=OFF)

  • Page 17

    50PD9800TA (FW1) Max. Init. Adj. Function Device ADJ. Items Mode Value Value 309 Reserved 310 Reserved 311 Reserved 312 Reserved 313 Reserved 314 Reserved 315 Reserved 316 Reserved 317 Reserved 318 Reserved 319 Reserved 320 Reserved 321 Reserved 322 Reserved...

  • Page 18

    50PD9800TA (FW1) Max. Init. Device Value Value 387 Reserved 388 Reserved 389 Reserved 390 Reserved 391 Reserved 392 Reserved 393 Reserved 394 Reserved 395 Reserved 396 Reserved 397 Reserved 398 Reserved 399 Custom tuning 0:SINGAPORE, 1:HONG_KONG, 2:AUSTRALIA, 3:CHINA, 4:Reserved 400 Mode display 0:Normal, 1:RF mode only, 2:Al...

  • Page 19

    50PD9800TA (FW1) Max. Init. Device Value Value 458 Upper Limits Value for Sync Detect of 2ms interva For Power Save at AV mod M30627 459 COLOR SYSTEM CONTROL-MODE(0:BW, 2:3.58NTSC, 3:4.43NTSC, Main M30627 460 COLOR SYSTEM CONTROL-MODE(0:BW, 2:3.58NTSC, 3:4.43NTSC, M30627 461 2ms synchronus count valu...

  • Page 20

    50PD9800TA (FW1) Max. Init. Device Value Value 535 Reserved 536 Reserved 537 Reserved 538 Reserved 539 Reserved 540 Reserved 541 Reserved 542 Reserved 543 Reserved 544 Reserved 545 Reserved 546 Reserved 547 Reserved 548 Reserved 549 Reserved 550 Reserved 551 Reserved...

  • Page 21

    50PD9800TA (FW1) Instructions in software renewal After software version up, set the following lists for reference. Service adjustment items by I C-bus control (MAIN (1) Part) Function Channel Select 0 CCIR 1 CHINA Australia Preset 0 None 1 Yes DTT Function Available 0 Not Available...

  • Page 22

    50PD9800TA (FW1) Power unit Adjustment Item Power Unit Vs,Va Ajustment Preparation Procedure (1) Turn on the set and perform Turn Vs ADJ to adjust Vs voltage pre-heat run more than 1 min to be within ±0.1V of the value on burn-in screen.

  • Page 23

    50PD9800TA (FW1) Amplitude Adjustment (Composite PAL) Item Preparation Procedure Receive Composite PAL adjustment signal and Input Composite PAL amplitude adjustment indicate Service Adjustment Menu.(Main (1)) signal into AV3 terminal. Select No.597 of Service Adjustment Menu. Press [OK] key more than 2 seconds to start the Black pattern: Set pedestal level.

  • Page 24

    50PD9800TA (FW1) Amplitude Adjustment (576p) Item Preparation Procedure Receive 576p adjustment signal, and indicate Input 576p adjustment signal into AV1 terminal. Service Adjustment Menu.(Main (1)) 8 Color Bar (Included 102 IRE White signal) Select No.597 of Service Adjustment Menu. Press [OK] key more than 2 seconds to start the automatic adjustment.

  • Page 25

    50PD9800TA (FW1) Amplitude Adjustment (PC D-Sub input) Item Preparation Procedure Receive PC signal (VGA [60Hz]), and indicate Input RGB amplitude adjustment signal of VGA Service Adjustment Menu.(Main) (60Hz) into RGB [D-sub] terminal. 8 Color Bar (Included 100 IRE Select No.597 of Service Adjustment Menu.

  • Page 26

    50PD9800TA (FW1) Video Color Temperature Adjustment (Cool) Item Adjustment Preparations Adjustment Procedures Set the signal generator output as All White. Perform the following adjustment with the remote control Component signal (480i) Set the CRT color analyzer (CA100) at the center Video level : 0.700Vp-p...

  • Page 27

    50PD9800TA (FW1) Video Color Temperature Adjustment (Warm) Item Preparation Procedure (1) Set signal generator output as Perform the following adjustment with the remote All White (Window ratio: 100%). control. (2) Component signal (480i) Set the CRT Color Analyzer (CA100) at the center Video level : 0.700Vp-p...

  • Page 28: Troubleshooting

    50PD9800TA (FW1) 7. Troubleshooting How to get to Burn-in mode This mode displays the test patterns of some single color raster in turn. These signals are from built-in gener- ator of panel. So it can be presumed that maybe the panel has some trouble when the screen of Burn-in mode is abnormal.

  • Page 29

    50PD9800TA (FW1) HDMI Picture [ Main PWB Circuit ] No Picture Are the output other than HDMI of the AV Recommended Signal ? device nomal ? (Table 1) *1 DVD Player or STB Check to Main PWB Check AV device...

  • Page 30

    50PD9800TA (FW1)

  • Page 31: Horizontal Frequency

    50PD9800TA (FW1) Recommended Signal List With HDMI input Signal mode Horizontal Dot clock frequency frequency Remarks Signal Vertical Resolution (kHz) (MHz) Name frequency (Hz) 640 X 480 59.94 31.47 25.18 EIA-861B 576i 720(1440) X 576 50.00 15.63 27.00 EIA-861B 480i 720(1440) X 480 59.94...

  • Page 32: Self-diagnosis Function

    50PD9800TA (FW1) 8. Self-Diagnosis Function This chassis has 2 modes of self-diagnosis function. (1) PDP panel check mode: It indicates the one latest record of the PDP panel failure with blinking of the power indication light (LED). (2) Signal circuit check mode: It indicates the check result on some points of the signal circuit and the history of them with On-Screen Display (OSD).

  • Page 33

    50PD9800TA (FW1) Signal circuit self-diagnosis function This function is for the failure of the signal circuit, for example the phenomenon as below: "Sometimes power turns off abnormally." "Sometimes picture disappears abnormally." To enter to this Self-Diagnosis mode, follow the next steps: Preparation: 1) The Power Cord should be connected to AC line and the Main Power switch should be turned on.

  • Page 34

    50PD9800TA (FW1) How to replace AC inlet plug For safety reason, please follow below procedure when replacing AC inlet plug (J901). 1) Remove Filter pwb from TV. 2) Remove 4pcs of screws (#04, #02) (Note: If solder will be found in the “+” portion of the screws, please remove solder first then remove screws.)

  • Page 35: Basic Circuit Diagram

    50PD9800TA (FW1) 9. Basic circuit diagram Waveform IY01(MAIN.V)(42) PIN IY01 CIN(MAIN S-VIDEO)(49) PIN IY01 YIN(MAIN S-VIDEO)(42) PIN 2Vp-p 2Vp-p 0.6V IY01 (Y)(50) PIN IY01(PB)(48)PIN IY01(PR)(49)PIN 1.4Vp-p 2Vp-p 1.4Vp-p...

  • Page 36

    50PD9800TA (FW1) Basic circuit diagram list PWB assembly MAIN 1 ............37 PWB assembly MAIN 2 ............38 PWB assembly MAIN 3 ............39 PWB assembly MAIN 4 ............40 PWB assembly MAIN 5 ............41 PWB assembly MAIN 6 ............42 PWB assembly MAIN 7 ............

  • Page 37: Pwb Assembly Main 1

    50PD9800TA (FW1) PWB assembly MAIN 1 (FW1)

  • Page 38: Pwb Assembly Main 2

    50PD9800TA (FW1) HDMI processing (approxlmately 7mA) -22V when 0.4V -22V when Notm -22V when Mount -22V when Notm -22V when Mount temporary PWB assembly MAIN 2 (FW1)

  • Page 39: Pwb Assembly Main 3

    50PD9800TA (FW1) PWB assembly MAIN 3 (FW1)

  • Page 40: Pwb Assembly Main 4

    50PD9800TA (FW1) PWB assembly MAIN 4 (FW1)

  • Page 41: Pwb Assembly Main 5

    50PD9800TA (FW1) PWB assembly MAIN 5 (FW1)

  • Page 42: Pwb Assembly Main 6

    50PD9800TA (FW1) PWB assembly MAIN 6 (FW1)

  • Page 43: Pwb Assembly Main 7

    50PD9800TA (FW1) PWB assembly MAIN 7 (FW1)

  • Page 44: Pwb Assembly Main 8

    50PD9800TA (FW1) PWB assembly MAIN 8 (FW1)

  • Page 45: Pwb Assembly Main 9

    50PD9800TA (FW1) XE90 NFM2012P13C105B SW+4.0V REG SW+2.6V REG 2125 SHEET-1 M_+5.4V SW+2.6V 1005 1005 RE91 RE92 RE93 300K-1% 7.5K-1% 270K-1% 270K-1% 110K-1% REA1 REA2 1005 1005 1005 REC0 REA0 CEC4 4.7/6.3 RE23 10K-1% 1005 RE25 CE00 I300 CE30 350mA TCFG3528...

  • Page 46: Pwb Assembly Main 10

    50PD9800TA (FW1) PWB assembly MAIN 10 (FW1)

  • Page 47: Pwb Assembly Main 11

    50PD9800TA (FW1) PWB assembly MAIN 11 (FW1)

  • Page 48: Pwb Assembly Main 12

    50PD9800TA (FW1) PWB assembly MAIN 12 (FW1)

  • Page 49: Pwb Assembly Sub 1 (jack/video Sw)

    50PD9800TA (FW1) PWB assembly SUB 1(JACK/VIDEO SW) (FW1)

  • Page 50: Pwb Assembly Sub 2 (tuner/a2 Nicam)

    50PD9800TA (FW1) AUSTRALIA PWB assembly SUB 2(TUNER/A2 NICAM) (FW1)

  • Page 51: Pwb Assembly Sub 3 (audio Sw/adc/dac)

    50PD9800TA (FW1) PWB assembly SUB 3(AUDIO SW/ADC/DAC) (FW1)

  • Page 52: Pwb Assembly Sub 4 (rs232c I/f)

    50PD9800TA (FW1) AUSTRALIA PWB assembly SUB 4(RS232C I/F) (FW1)

  • Page 53: Pwb Assembly Sub 5 (cn I/f )

    50PD9800TA (FW1) PWB assembly SUB 5(CN I/F) (FW1)

  • Page 54: Pwb Assembly Filter

    50PD9800TA (FW1) PWB assembly FILTER (FW1)

  • Page 55: Pwb Assembly Control (front Input )

    50PD9800TA (FW1) PWB assembly CONTROL (Front Input) (FW1)

  • Page 56: Pwb Assembly Control (led )

    50PD9800TA (FW1) PWB assembly CONTROL (LED) (FW1)

  • Page 57: Printed Wiring Board Diagram

    50PD9800TA (FW1) 10. Printed wiring board diagram PWB assembly MAIN (side-A)

  • Page 58

    50PD9800TA (FW1) PWB assembly MAIN (side-B)

  • Page 59

    50PD9800TA (FW1) PWB assembly SUB (side-A) PWB assembly SUB PWB assembly SD PWB assembly SWIVEL PWB assembly LED PWB assembly SENSOR...

  • Page 60

    50PD9800TA (FW1) PWB assembly SUB (side-B) PWB assembly SUB PWB assembly LED PWB assembly SWIVEL PWB assembly SD PWB assembly SENSOR...

  • Page 61

    50PD9800TA (FW1) PWB assembly FILTER PWB assembly LED PWB assembly CONTROL...

  • Page 62: Block Diagram

    50PD9800TA (FW1) 11. Block diagram IH01 IH05 60h/68h 2Kbit HDMI Rx EEPROM SiI9023 S-24CS02A Y/G,Cb/B,Cr/R PDP: 30h Panel HDMI-1 5/3.3V HDCP HSYNC TMDS TMDS VSYNC IE30 TMDS TMDS IE60 IEU0 I3K0 256Mbit DDR400 64Kbit HDMI-2 5/3.3V HDCP IH07 32Mbit Flash...

  • Page 63: Connection Diagram

    50PD9800TA (FW1) 12. Connection diagram...

  • Page 64: Wiring Diagram

    50PD9800TA (FW1) 13. Wiring diagram [ 50PD9800TA 1/2 ]...

  • Page 65

    50PD9800TA (FW1) [ 50PD9800TA 2/2]...

  • Page 66: Disassembly Diagram

    50PD9800TA (FW1) 14. Disassembly diagram [ 50PD9800 Disassembly Diagram 1 ] #200A code Material (PC+ABS) Acrylonitrile Butadine Styrene #131 Steel #133 PolyStyrene #212 #0800 PC+ABS PolyCarbonate + Acrylonitrile Butadine Styrene (PS) Aluminium #219 #233 #208 (PS) #210 (PS) Power button assembly...

  • Page 67

    50PD9800TA (FW1) [ 50PD9800 Disassembly Diagram 2 ] Chassis - 1 Chassis - 2 Chassis Unit Chassis - 3 #709 #709...

  • Page 68

    50PD9800TA (FW1) [ 50PD9800 Disassembly Diagram 3 ] Chassis - 4 Backcover assembly #917 Positioning Pin Be Careful not to injure flexible cables of PDP module. #306 CAUTION Panel assmble it as the fi gure in case of attachment based on the MAIN FARME upper Positioning Pin.

  • Page 69

    50PD9800TA (FW1) [ 50PD9800 Disassembly Diagram 4 ] PWB assembly MAIN - 1 Terminal / PWB assembly POWER PWB assembly MAIN - 2...

  • Page 70

    50PD9800TA (FW1) [ 50PD9800 Disassembly Diagram 5 ] 8. X-BUS U PWB Ass'y Attachment for packing 3. X-SUS PWB Ass'y Apply it before packing this panel module. 9. X-BUS D PWB Ass'y 4. Y-SUS PWB Ass'y 6. A-BUS R PWB Ass'y 7.

  • Page 71: Replacement Parts List

    50PD9800TA (FW1) 15. Replacement Parts list PRODUCT SAFETY NOTE : Components marked with a have special characteristics important to safety. Before replacing any of there components,read carefully,the CAUTION FOR SAFETY of this Service Manual. Don't degrade the safety of the receiver through improper servicing.

  • Page 72

    50PD9800TA (FW1) PRODUCT SAFETY NOTE : Components marked with a have special characteristics important to safety. Before replacing any of there components,read carefully,the CAUTION FOR SAFETY of this Service Manual. Don't degrade the safety of the receiver through improper servicing.

  • Page 73

    50PD9800TA (FW1) PRODUCT SAFETY NOTE : Components marked with a have special characteristics important to safety. Before replacing any of there components,read carefully,the CAUTION FOR SAFETY of this Service Manual. Don't degrade the safety of the receiver through improper servicing.

  • Page 74

    50PD9800TA (FW1) PRODUCT SAFETY NOTE : Components marked with a have special characteristics important to safety. Before replacing any of there components,read carefully,the CAUTION FOR SAFETY of this Service Manual. Don't degrade the safety of the receiver through improper servicing.

  • Page 75

    50PD9800TA (FW1) PRODUCT SAFETY NOTE : Components marked with a have special characteristics important to safety. Before replacing any of there components,read carefully,the CAUTION FOR SAFETY of this Service Manual. Don't degrade the safety of the receiver through improper servicing.

  • Page 76

    50PD9800TA (FW1) PRODUCT SAFETY NOTE : Components marked with a have special characteristics important to safety. Before replacing any of there components,read carefully,the CAUTION FOR SAFETY of this Service Manual. Don't degrade the safety of the receiver through improper servicing.

  • Page 77

    50PD9800TA (FW1) PRODUCT SAFETY NOTE : Components marked with a have special characteristics important to safety. Before replacing any of there components,read carefully,the CAUTION FOR SAFETY of this Service Manual. Don't degrade the safety of the receiver through improper servicing.

  • Page 78

    50PD9800TA (FW1) PRODUCT SAFETY NOTE : Components marked with a have special characteristics important to safety. Before replacing any of there components,read carefully,the CAUTION FOR SAFETY of this Service Manual. Don't degrade the safety of the receiver through improper servicing.

  • Page 79

    50PD9800TA (FW1) PRODUCT SAFETY NOTE : Components marked with a have special characteristics important to safety. Before replacing any of there components,read carefully,the CAUTION FOR SAFETY of this Service Manual. Don't degrade the safety of the receiver through improper servicing.

  • Page 80

    50PD9800TA (FW1) PRODUCT SAFETY NOTE : Components marked with a have special characteristics important to safety. Before replacing any of there components,read carefully,the CAUTION FOR SAFETY of this Service Manual. Don't degrade the safety of the receiver through improper servicing.

  • Page 81

    50PD9800TA (FW1) PRODUCT SAFETY NOTE : Components marked with a have special characteristics important to safety. Before replacing any of there components,read carefully,the CAUTION FOR SAFETY of this Service Manual. Don't degrade the safety of the receiver through improper servicing.

  • Page 82

    50PD9800TA (FW1) PRODUCT SAFETY NOTE : Components marked with a have special characteristics important to safety. Before replacing any of there components,read carefully,the CAUTION FOR SAFETY of this Service Manual. Don't degrade the safety of the receiver through improper servicing.

  • Page 83

    50PD9800TA (FW1) PRODUCT SAFETY NOTE : Components marked with a have special characteristics important to safety. Before replacing any of there components,read carefully,the CAUTION FOR SAFETY of this Service Manual. Don't degrade the safety of the receiver through improper servicing.

  • Page 84

    50PD9800TA (FW1) PRODUCT SAFETY NOTE : Components marked with a have special characteristics important to safety. Before replacing any of there components,read carefully,the CAUTION FOR SAFETY of this Service Manual. Don't degrade the safety of the receiver through improper servicing.

  • Page 85

    50PD9800TA (FW1) PRODUCT SAFETY NOTE : Components marked with a have special characteristics important to safety. Before replacing any of there components,read carefully,the CAUTION FOR SAFETY of this Service Manual. Don't degrade the safety of the receiver through improper servicing.

  • Page 86

    50PD9800TA (FW1) PRODUCT SAFETY NOTE : Components marked with a have special characteristics important to safety. Before replacing any of there components,read carefully,the CAUTION FOR SAFETY of this Service Manual. Don't degrade the safety of the receiver through improper servicing.

  • Page 87

    50PD9800TA (FW1) PRODUCT SAFETY NOTE : Components marked with a have special characteristics important to safety. Before replacing any of there components,read carefully,the CAUTION FOR SAFETY of this Service Manual. Don't degrade the safety of the receiver through improper servicing.

  • Page 88

    50PD9800TA YK No.040E QR70537 Printed in Japan (JE)

Comments to this Manuals

Symbols: 0
Latest comments: