Illumination; Timekeeping; Adjusting Home Positions - Casio 5133 Operation Manual

Operation Guide 5133

Illumination

An LED (light-emitting diode) and light guide panel
illuminate the face of the watch for easy reading in the
dark.
• See "Illumination Precautions" on page E-68 for other
important information.
To turn on illumination
In any mode (except when a setting is on the display),
press B to illuminate the face of the watch for about one
second.
E-40
Read This Before You Set the Time and Date!
This watch is preset with a number of city codes, each of which represents the time
zone where that city is located. When setting the time, it is important that you fi rst
select the correct city code for your Home City (the city where you normally use the
watch). If your location is not included in the preset city codes, select the preset city
code that is in the same time zone as your location.
• Note that all of the times for the World Time Mode city codes (page E-30) are
displayed in accordance with the time and date settings you confi gure in the
Timekeeping Mode.
• The watch automatically adjusts its analog setting to match the current digital setup
of your Home City. If the analog time is not correct even though you are sure the
digital setup of your Home City is correct and the watch is performing signal
reception properly, check the home positions of the hands and make adjustments if
necessary (page E-49).
E-42
12/24-Hour
City Code DST
Format
Power Saving Button Operation Tone
3. When the timekeeping setting you want to change is fl ashing, use D or B to
change it as described below.
Screen: To do this:
Change the city code
Cycle between Daylight Saving Time (ON),
Standard Time (OFF), and Auto DST
(AUTO)
Toggle between 12-hour (12H) and
24-hour (24H) timekeeping
Reset the seconds to 00
E-44
Daylight Saving Time (DST)
Daylight Saving Time (summer time) advances the time setting by one hour from
Standard Time. Remember that not all countries or even local areas use Daylight
Saving Time.
The time calibration signals transmitted from Mainfl ingen (Germany), Anthorn
(England), or Fort Collins (the United States) include both Standard Time and DST
data. When the Auto DST setting is turned on, the watch switches between Standard
Time and DST (summer time) automatically in accordance with the signals.
• Though the time calibration signals transmitted by the Fukushima and Fukuoka/
Saga, Japan transmitters include summer time data, summer time currently is not
implemented in Japan (as of 2013).
• The default DST setting is Auto DST (AUTO) whenever you select LIS, LON, MAD,
PAR, ROM, BER, STO, ATH, MOW, TYO, ANC, YVR, LAX, YEA, DEN, MEX, CHI,
NYC, YHZ, or YYT as your Home City code.
• If you experience problems receiving the time calibration signal in your area, it is
probably best to switch between Standard Time and Daylight Saving Time (summer
time) manually.
E-46
Analog Timekeeping
The analog time of this watch is synchronized with the digital time. The analog time
setting is adjusted automatically whenever you change the digital time.
Note
• The hands for the analog timepiece move to adjust to a new setting whenever any
of the following occurs.
When you change the digital time setting manually
When the digital time setting is changed by time calibration signal reception
When you change the Home City code and/or DST setting
• If the analog time does not match the digital time for any reason, use the procedure
described under "To adjust home positions" (page E-49) to match the analog
setting to the digital setting.
• Whenever you need to adjust both the digital and the analog time settings manually,
make sure you adjust the digital setting fi rst.
• Depending on how much the hands have to move in order to adjust to the digital
time, it may take some time before they stop moving.
E-48
Seconds Hour Minutes
Day Month Year
Do this:
Use D (East) and B (West).
Press D.
Press D.
Press D.

Timekeeping

Use the Timekeeping Mode to set and view the current time and date. This section
also explains how to manually set the current date and time.
• When setting the time, you can also confi gure settings for the 12/24-hour format.
• Each press of cycles the digital display in the sequence shown below.
Month Press . Second
Day Hour : Minutes
• All of the operations in this section are performed in the Timekeeping Mode, which
you can enter by pressing (page E-8).
To set the current digital time and date manually
1. In the Timekeeping Mode, hold down A for about two
City code
seconds until the watch beeps and ADJ appears on the
display.
• This will cause the currently selected city code to
fl ash.
2. Press C to move the fl ashing in the sequence shown
below to select other settings.
Screen: To do this:
Change the hour or minutes
Change the year
Change the month or day
Toggle the button operation tone between
/
(on) and (off)
Toggle Power Saving on (PSON)
and off (PSOF)
• See "City Code Table" at the back of this manual for a complete list of available
city codes.
• Auto DST (AUTO) can be selected only while LIS, LON, MAD, PAR, ROM,
BER, STO, ATH, MOW, TPE, SEL, TYO, HNL, ANC, YVR, LAX, YEA, DEN,
MEX, CHI, NYC, YHZ, or YYT is selected as the Home City code. For more
information, see "Daylight Saving Time (DST)" (page E-46).
• For information about settings other than the time and date, see the following.
Power Saving: Power Saving Function (page E-60)
4. Press A to exit the setting screen.
To change the Daylight Saving Time (summer time) setting
1. In the Timekeeping Mode, hold down A for about two seconds until the watch
beeps and ADJ appears on the display.
• This will cause the currently selected city code to fl ash.
2. Press C once and the DST setting screen appears.
3. Use D to cycle through the DST settings in the sequence shown below.
Auto DST (AUTO) DST off (OFF)
4. When the setting you want is selected, press A to exit the setting screen.
• The DST indicator appears on the display to indicate that Daylight Saving Time
is turned on.

Adjusting Home Positions

Strong magnetism or impact can cause the hands of the watch to be off, even if the
watch is able to perform the signal receive operation. If this happens, perform the
applicable home position adjustment procedures in this section.
• Hand home position adjustment is not required if the analog time and digital time
are the same in the Timekeeping Mode.
To adjust home positions
1. In the Timekeeping Mode, hold down A for about fi ve
seconds. You can release the button after "H-SET"
appears on the display.
• Though "ADJ" will appear on the display after about
two seconds, do not release the button yet. Keep it
depressed until "H-SET" appears.
• The hour and minute hands should move to 12
o'clock (their home position), and "0:00" should
fl ash on the display.
Correct hour and
minute hand positions
PM indicator Day of week
E-41
E-43
Do this:
Use D (+) and B (–).
Press D.
Press D.
E-45
DST on (ON)
E-47
E-49