DeWalt DCD732 Original Instructions Manual
  1. Manuals
  2. Brands
  3. DeWalt Manuals
  4. Drill
  5. XR Li-Ion DCD732
  6. Original instructions manual
DeWalt DCD732 Original Instructions Manual

DeWalt DCD732 Original Instructions Manual

Brushless cordless compact 13 mm (1/2") drill/driver
Hide thumbs Also See for DCD732:
Table of Contents

Advertisement

Quick Links

See also: Manual , Original Instruction Manual
DCD732
DCD737
DCD790
DCD795
FINAL PRINT SIZE: A5 (148 x 210 mm)

Advertisement

Table of Contents
loading

Related Manuals for DeWalt DCD732

Summary of Contents for DeWalt DCD732

  • Page 1 DCD732 DCD737 DCD790 DCD795 FINAL PRINT SIZE: A5 (148 x 210 mm)
  • Page 2 English (original instructions) Copyright D WALT...
  • Page 3 FIG. 1 DCD795 FIG. 2...
  • Page 4 FIG. 3 FIG. 4 FIG. 5 FIG. 6 FIG. 7 FIG. 8 FIG. 9...

  • Page 5: Technical Data

    English BRUSHLESS CORDLESS COMPACT 13 mm (1/2") DRILL/DRIVER, DCD732, DCD790 BRUSHLESS CORDLESS COMPACT 13 mm (1/2") DRILL/DRIVER/HAMMERDRILL, DCD737, DCD795 Congratulations! You have chosen a D WALT tool. Years of experience, thorough product development and innovation make WALT one of the most reliable partners for professional power tool users.

  • Page 6: Definitions: Safety Guidelines

    English The vibration emission level given in this information Charger DCB105 sheet has been measured in accordance with a Mains voltage standardised test given in EN60745 and may be used to compare one tool with another. It may be Battery type 10.8/14.4/18 Li-Ion used for a preliminary assessment of exposure.

  • Page 7: Ec Declaration Of Conformity

    COMPACT DRILL/DRIVER/HAMMERDRILL Avoid body contact with earthed or DCD732, DCD737, DCD790, DCD795 grounded surfaces such as pipes, WALT declares that these products described radiators, ranges and refrigerators. There under Technical Data are in compliance with:...
  • Page 8 English Prevent unintentional starting. Ensure cutting edges are less likely to bind and are the switch is in the off position before easier to control. connecting to power source and/or Use the power tool, accessories and battery pack, picking up or carrying the tool bits etc., in accordance with these tool.

  • Page 9: Residual Risks

    English • Wear safety goggles or other eye protection. • Before using the charger, read all instructions Hammering and drilling operations cause chips and cautionary markings on charger, battery to fly. Flying particles can cause permanent eye pack and product using the battery pack. damage.

  • Page 10: Charging Process

    English • When operating a charger outdoors, always continuously indicating that the charging process has started. provide a dry location and use an extension cord suitable for outdoor use. Use of a cord 3. The completion of charge will be indicated by suitable for outdoor use reduces the risk of the red light remaining ON continuously.

  • Page 11: Important Safety Instructions For All Battery Packs

    English charging cycle and will not return to maximum falling hazard. Some tools with large charge rate even if the battery warms. battery packs will stand upright on the battery pack but may be easily knocked LITHIUM ION BATTERY PACKS ONLY over.

  • Page 12: Battery Pack

    Battery Pack Have defective cords replaced immediately. BATTERY TYPE The DCD732 and DCD737 operate on 14.4 volt Charge only between 4 ˚C and 40 ˚C. battery packs. The DCD790 and DCD795 operate on 18 volt Only for indoor use.

  • Page 13: Electrical Safety

    English Description (Fig. 1, 2) Mains Plug Replacement (U.K. & Ireland Only) WARNING: Never modify the power tool or any part of it. Damage or personal If a new mains plug needs to be fitted: injury could result. • Safely dispose of the old plug. a.

  • Page 14: Variable Speed Trigger Switch

    English To actuate the fuel gauge, press and hold the fuel NOTE: The torque adjustment collar is only gauge button (l). A combination of the three green engaged during screwdriving mode and not in drill LED lights will illuminate designating the level of and hammerdrill modes.
  • Page 15 English Proper Hand Position (Fig. 3) 3. Insert the accessory about 19 mm (3/4") into the chuck and tighten securely by rotating WARNING: To reduce the risk of serious the chuck sleeve clockwise with one hand personal injury, ALWAYS use proper while holding the tool with the other.

  • Page 16: Optional Accessories

    English MAINTENANCE 8. Keep the motor running when pulling the bit back out of a drilled hole. This will help prevent Your D WALT power tool has been designed to jamming. operate over a long period of time with a minimum 9.

  • Page 17: Protecting The Environment

    English be hazardous. To reduce the risk of • Li-Ion cells are recyclable. Take them to your injury, only D WALT, recommended dealer or a local recycling station. The collected accessories should be used with this battery packs will be recycled or disposed of properly.
  • Page 20 Belgique et WALT - Belgium BVBA Tel: NL 32 15 47 37 63 www.dewalt.be Luxembourg België Egide Walschaertsstraat 16 Tel: FR 32 15 47 37 64 enduser.BE@SBDinc.com en Luxemburg 2800 Mechelen Fax: 32 15 47 37 99 Danmark WALT Tel: 70 20 15 10 www.dewalt.dk...

This manual is also suitable for:

Dcd795Dcd737Dcd790

Table of Contents