Advertisement
General
The heater has a loading of 2kW.
Heat output and temperature control on this appliance are
provided using the electronic control. With the unit plugged
in, and by pressing the 'STAND-BY' button (see '1' in Fig.
4) the heater can be activated. The appliance is provided
with a handle for easy carrying - see Fig. 3.
Operation - see Fig. 4
The heat output is electronically controlled, according to
the room temperature.
To activate the appliance press the 'STAND-BY' button -
see '1' in Fig. 4.
Press button '2' to select Fan only/Low heat/High heat. By
pressing this button once Fan only is selected, pressing
twice provides Low heat and by pressing three times High
heat is selected.
On the display screen (see Fig. 4) two temperature
readings appear at the top of the screen. The room
ambient temperature appears on the right and the desired
temperature appears on the left hand side.
Use buttons '3' and '4' to set the desired room temperature
when Low or High heat is selected.
The temperature can be set from 5
will be shown on the display. When the temperature is
reached the heater will automatically switch off. If the
ambient temperature drops the heater will come on again
automatically. Note the electronic climate control device
conserves energy and assists with temperature regulation
e.g. if the heater is set to HIGH heat and the temperature
is set to 28
C, at 27
C the heater will switch to LOW heat.
o
o
Then at 28
C the heater will switch OFF completely.
o
An audible beep can be heard when any button is pressed.
A double beep can be heard when 5° and 35° is selected;
the upper and lower limits.
By keeping buttons '3' and '4' pressed down the user can
scroll quickly to the desired temperature.
Note: The heater retains it's last setting once the appliance
has been switched off or disconnected from the power
supply.
Overheat cut-out
The built-in overheat cut-out switches off the appliance
automatically in the event of a fault. Disconnect the mains
plug from the socket. After a short cooling down phase,
the appliance switches into stand-by mode and is ready for
use again. If the fault should occur again, follow the after
sales advice.
Fuselink
A thermal fuse link is provided as an added safety feature.
If the fuse link operates and opens circuit it is the result of
abnormal overheating within the appliance and servicing
of the appliance by a competent service engineer will be
required in order to ensure the future safe operation of the
heater. Customer services should be contacted, who will
arrange the replacement of any faulty parts and the fitting
of a new fuse link.
[c] Dimplex UK Limited
All rights reserved. Material contained in this publication may not be reproduced in whole or in part, without prior permission in writing of Dimplex UK Limited.
C to 35
C and this
o
o
Cleaning
WARNING : Always disconnect from power supply
before cleaning heater.
Do not use detergents, abrasive cleaning powders or polish
of any kind on the heater.
Wipe with a dry cloth to remove dust and a damp cloth (not
wet) to clean off stains. Be careful not to allow moisture
into the heater.
Ensure that dust or fluff does not accumulate inside the
heater as this could lead to overheating of the element.
Use a vacuum cleaner to remove any fluff which does
accumulate.
Recycling
For electrical products sold within the European
Community.
At the end of the electrical products useful life
it should not be disposed of with household
waste. Please recycle where facilities exist.
Check with your Local Authority or retailer for
recycling advice in your country.
After Sales Service
Your product is guaranteed for three years from the date of
purchase. After sales information or assistance with this
product can be found on our website:
www.dimplex.co.uk/support
Your rights under this guarantee are additional to your
statutory rights, which in turn are not affected by this
guarantee.
Please do not return a faulty product to us as this may
result in loss or damage and delay in providing you with a
satisfactory service.
If after following these steps your product still does not
operate you should return it to your point of purchase.
Please retain your receipt as proof of purchase.
Advertisement
