Page 1
RC-BAS10 VS SX-C610 • This Service Manual is the “Revision Publishing” and replaces “Simple Manual” of NSX-HMT35 <U>, (S/M Code No. 09-014-445-1T1). • If requiring information about the CD mechanism, see Service Manual of BZG-5, (S/M Code No. 09-00C-353-3N2). u163 S/M Code No.
http://www.xiaoyu163.com SPECIFICATIONS 3 7 63 1515 0 MAIN UNIT CX-NDS50 / CX-NDS55 GENERAL Power requirements 120 V AC, 60 Hz TUNER Power consumption 130 W FM tuning range 87.5 MHz to 108 MHz Power consumption With ECO mode on: 0.6 W FM usable sensitivity (IHF) 13.2 dBf in standby mode...
http://www.xiaoyu163.com PROTECTION OF EYES FROM LASER BEAM DURING SERVICING 3 7 63 1515 0 This set employs laser. Therefore, be sure to follow carefully CAUTION the instructions below when servicing. Use of controls or adjustments or performance of proce- dures other than those specified herin may result in WARNING!! hazardous radiation exposure.
http://www.xiaoyu163.com NOTE ON BEFORE STARTING REPAIR 1. Forced discharge of electrolytic capacitor of power supply block 3 7 63 1515 0 When repair is going to be attempted in the set that uses relay circuit in the power supply block, electric potential is kept charged across the electrolytic capacitors (C101, 102) even though AC power cord is removed.
Page 5
http://www.xiaoyu163.com 3 7 63 1515 0 In such a case, check also if the POWER AMPLIFIER circuit or power supply circuit has any abnormalities or not. 2-2. Regarding reset There are cases that the machine does not work correctly because the MICROCOMPUTER is not reset even though the AC power cord is re-inserted, or the software reset (pressing the STOP key + POWER key) is performed.
http://www.xiaoyu163.com TRANSISTOR ILLUSTRATION 3 7 63 1515 0 B C E E C B E C B E C B CSB1370EF CDA1585BC 2SA1980G CSC4115BC KTC3198GR 2SA1981Y CC5551 B C E G D S 2SB1342 2SK2937 2SK2158 2SA1235F DTC114YKA 2SD1933 2SC2714O KRA102S FN1016 2SC3052F...
Page 12
http://www.xiaoyu163.com WIRING – 1 (MAIN / DSP) 3 7 6 3 1 5 1 5 0 1 3 9 4 2 2 9 6 5 1 3 w w w u 1 6 3 – 12 – http://www.xiaoyu163.com...
Page 28
http://www.xiaoyu163.com 3 7 63 1515 0 Pin No. Pin Name Description I-TU_SIG Tuner signal input. (Not used) AVSS – GND. O-PLL_CLK PLL IC clock enable output. O-PLL_CE PLL IC chip enable output. 53, 54 P1, P2 FL segment P1, P2 output. O-CD_CLK CD clock output.
Page 29
http://www.xiaoyu163.com ADJUSTMENT <TUNER / FRONT / DECK> 3 7 63 1515 0 < TUNER SECTION > < DECK SECTION > 1. Clock Frequency Check 9. Tape Speed Adjustment (DECK 2) Settings : • Test point : TP2(CLK) Settings : • Test tape : TTA–100 Method : Set to AM 1710kHz and check that the test point is •...
http://www.xiaoyu163.com CD TEST MODE 3 7 63 1515 0 1. How to Start the CD Test Mode While pressing the FUNCTION button, insert the AC plug to the power outlet. When the test mode is started, the message [CD TEST] is displayed. 2.
Page 31
http://www.xiaoyu163.com MECHANICAL EXPLODED VIEW 1 / 1 3 7 6 3 1 5 1 5 0 BZG-5 WIRE,BINDER WIRE, BINDER HT-SINK, ASSY S 1 3 9 4 2 2 9 6 5 1 3 HT-SINK, w w w u 1 6 3 ZZM-3 PLATE,EARTH MECH CHAS,MAIN...
http://www.xiaoyu163.com GENERAL SPEAKER DISASSEMBLY INSTRUCTIONS (FOR REFERENCE) 3 7 63 1515 0 Type.1 Type.4 Insert a flat-bladed screwdriver into the position indicated by the TOOLS arrows and remove the panel. Remove the screws of each speaker 1 Plastic head hammer unit and then remove the speaker units.
Need help?
Do you have a question about the NSX-HMT35 and is the answer not in the manual?
Questions and answers