Midas M32R User Manual page 28

54 DIGITAL RACK MIXER M32R User Manual
Permanent MIDI Assignments Overview (Remote Off )
MIDI RX MIDI Ch Controller Value
Scenes 1 Program Change 1-100
Snippet 2 Program Change 1-100
Cue 3-6 Program Change 0-127
Mute Groups 2 CC80-85 on (127) / off (0), toggle latching
Faders 1 CC0-79 0-127
Mute 2 CC0-79 on (127) / off (0), toggle latching
Pan 2 CC0-79 0-127
MIDI TX MIDI Ch Controller Value
Mute Groups 2 CC80-85 on (127) / off (0), toggle latching
Faders 1 CC80-79 0-127
Mute 2 CC80-79 on (127) / off (0), toggle latching
Pan 3 CC80-79 0-127
MIDI RX > Assign
Whenever assignable controls are set up for transmitting MIDI commands,
reception of that same command (status or continuous) will be refl ected on the
respective assignable control element (button light, encoder LED collar).
MIDI TX > Assign
The assignable MIDI commands have been restricted to some generic elements:
Encoders 1-4 > can be assigned to sending control changes, program changes
or notes.
• • Parameters are currently 'Channel' and 'Value'
• • For CC and Note commands 'Value' = controller number/note
number, and the encoder rotation determines the controller value/
note-on velocity
• • For Program Changes only the channel is specifi ed, and the encoder
rotation determines the program number
Buttons 5-12 > can be operated in two modes, 'MIDI Push' (non-latching) for
momentary commands, or 'MIDI Toggle' (latching) for static commands.
MIDI Push
Can be assigned to sending control changes, program changes or notes
Parameters are currently 'Channel' and 'Value'
For CC and Note commands 'Value' 0...127 = controller number/note number,
and the button momentarily toggles the controller value/note-on velocity
To 127 (depressed/released]
For Program Changes 'Value' 0...127 = program/preset number, that will be sent
upon pressing the button.
Comment
Ch3 -> Cue 1-127, Ch4 -> Cue 128-255, etc.
Value 95 = 0dB
Value 64 = Pan Mid
Comment
Value 95 = 0dB
Value 64 = Pan Mid
MIDI Toggle
Can be assigned to sending control changes or notes
Parameters are currently 'Channel' and 'Value'
For CC and Note commands 'Value' 0...127 = controller number/note number,
and the button toggles the controller value/note-on velocity
Between value/velocity 127 and 0 with every operation.
PLEASE NOTE:
The ASSIGN section also refl ects/displays reception of the same MIDI commands
that are selected for transmission
The MIDI commands assigned to the ASSIGN controls can be transferred to and
from stage via AES50 using the S16 stage box MIDI I/O.
MIDI RX/TX > Remote
Enables a specifi c form of bi-directional MIDI communication for remote
controlling a computer DAW application using control elements of the
M32 console. REMOTE can be used in three modes, Mackie Control, HUI and
raw MIDI CC (raw) controllers (see SETUP / remote)
55 DIGITAL RACK MIXER M32R User Manual
MIDI CC (raw) selected and Remote is enabled+active, the group section controls
will transmit/receive the following messages:
MIDI RX MIDI Ch Controller
Group 1-8 SELECT 1
Group 1-8 SOLO 1
Group 1-8 MUTE 1
Sends On Fader 1
Group DCA 1-8 1
BUS 1-8 1
BUS 9-16 1
MTX 1-6 1
GROUP Faders 1
HUI selected and Remote is enabled+active, then the group fader section and
buttons will emulate the HUI control surface protocol, i.e. for ProTools.
SELECT/SOLO 1-8 buttons will select or solo the corresponding track in the DAW,
in banks of eight tracks
Sends On Fader = enables touch-writing a fader automation on selected track,
track automation mode in DAW must be 'touch', (latching)
Use the layer buttons to determine the function assigned to
the MUTE 1-8 buttons, the LED displays indicate that function.
Group DCA 1-8 = allows movement of the bank selection of tracks
• •
in a DAW, (push non-latching)
• • BUS 1-8 = allows the setting of DAW tracks to 'Record Ready',
(push non-latching)
• • BUS 9-16 = enables use of MUTE buttons for track mute in
the DAW, (latching)
• • MTX 1-6 = enables use of MUTE buttons for transport controls in
the DAW, (latching).
MACKIE CTRL selected and Remote is enabled+active, then the group fader
section and buttons will emulate the Mackie Control Universal protocol
SELECT/SOLO 1-8 buttons will select or solo the corresponding track in the DAW,
in banks of eight tracks
Sends On Fader = enables touch-writing a fader automation on selected track,
track automation mode in DAW must be 'touch' or 'latch', (latching)
Use the layer buttons to determine the function assigned to the
MUTE 1-8 buttons, the LED displays indicate that function.
• • Group DCA 1-8 = allows movement of the bank selection of tracks in a
DAW, (push non-latching)
• • BUS 1-8 = allows the setting of DAW tracks to 'Record Ready',
(push non-latching)
• • BUS 9-16 = enables use of the MUTE buttons for track mute in
the DAW, (latching)
• • MTX 1-6 = enables use of the MUTE buttons for transport controls in
the DAW, (latching).
Comment
Note 64-71 on (127) / off (0), push non-latching
CC 32-39 on (127) / off (0), toggle latching
CC 40-47 on (127) / off (0), toggle latching
CC 48 on (127) / off (0), toggle latching
Note 72 on (127) / off (0), push non-latching
Note 73 on (127) / off (0), push non-latching
Note 74 on (127) / off (0), push non-latching
Note 75 on (127) / off (0), push non-latching
CC0-7 0-127