Table of Contents
Advertisement
Function setting
LED
DELTA
Green LED On
2 AILE
Green LED On
DELTA and 2 AILE
2 Green LED On
NOTICE
You may select only 1 function of delta, 2 aile and V-tail
When T5/mz-10 is switched on, the status LED of each function that you set is turned on for
5 seconds to indicate which function has been set.
10. FailSafe
When you bind your transmitter, you are programming the receiver with failsafe defaults. Graupner/SJ
receiver has 4 Failsafe modes: FAILSAFE, HOLD, OFF and STANDARD.
1. Switch on the receiver and place transmitter RF TRAIN-
ER SWITCH at normal position. Press and hold the MODE
button and switch on the transmitter. The Graupner/SJ logo
repeat to blink a single red with a single beep, indicating that you
entered the failsafe mode. Every time you press MODE button at
failsafe mode, the 4 modes are changed in turns.
Button
Mode
FAILSAFE
Repeating that the Graupner/SJ logo blinks a single red with a single beep
HOLD
Repeating that the Graupner/SJ logo blinks twice red with twice beeps
Once
OFF
Repeating that the Graupner/SJ logo blinks three times red with three times beeps
Once more
STANDARD
Repeating that the Graupner/SJ logo blinks four times red with four times beeps
Once more
Description
Delta wing function is activated,
2 Aile and V-tail functions are de-activated.
2 Aile function is activated,
Delta and V-tail functions are de-activated.
V-tail function is activated,
Delta and 2 aile functions are de-activated.
Normal
Teacher
Pupil
LED status and beep
1-2. Failsafe mode
- FAILSAFE
Move the control sticks on the transmitter to the desired preset failsafe positions. Press & hold the
MODE button for over 2 sec and release the button. The Graupner/SJ logo turns solid red, indicating
the failsafe mode has been set. Confirm the failsafe setting is correct by turning off the transmitter.
The throttle should go to the preset position.
- HOLD
Enter hold mode by pressing MODE button once from the failsafe mode. The Graupner/SJ logo
repeats to blink twice red with twice beep. Press & hold the MODE button for over 2 sec and release
the button. The Graupner/SJ logo turns solid red, indicating the hold mode has been set. If you lose
connection, all channels hold the last given command.
- OFF
Enter off mode by pressing MODE button once from the hold mode. The Graupner/SJ logo repeats
to blink 3 times red with 3 times beep. Press & hold the MODE button for over 2 sec and release
the button. The Graupner/SJ logo turns solid red, indicating the off mode has been set. Even if you
lose connection, the failsafe is not working.
- STANDARD
Enter standard mode by pressing MODE button once from the hold mode. The Graupner/SJ logo
repeats to blink 4 times red with 4 times beep. Press & hold the MODE button for over 2 sec and
release the button. The Graupner/SJ logo turns solid red, indicating the standard mode has been
set. standard features that the throttle channel ( channel Number 1 ) is move into low throttle
position and other channels hold last given command.
NOTICE
Failsafe setting could be only set in case that RF TRAINER SWITCH
is at normal flight position
11. RF Trainer
The T5/mz-10 has the trainer function. The function activates when you select Teacher, Pupil and
Normal mode by RF TRAINER SWITCH.
1). Mode setting
1-1. Teacher setting
Move transmitter's RF TRAINER SWITCH of the TEACHER transmitter to TEACHER position.
Press & hold the MODE button and switch on the transmitter. The Graupner/SJ logo repeats to
blink twice red with twice beeps, indicating that you set TEACHER Mode. After two beeps sound
twice, two beeps don't sound. Now the T5/mz-10 can bind and control all channels of the pupil's
transmitter without restriction.
7
Advertisement
Table of Contents
