Page 1
Operating Instructions (ENG) FROM SERIAL #10020080000118 MODELS: CB20 CBCD20 10020080 10020160 CBE20 10020100 Read these instructions before using the machine. 86306300-R 02/03/09 Downloaded from www.Manualslib.com manuals search engine...
Page 2
Name: __________________________________________________________________________________________________ Address: _______________________________________________________________________________________________ Phone Number: _________________________________________________________________________________________ OVERVIEW The Chariot burnisher is a battery powered, ride-on, hard floor burnisher intended for commercial use. The appliance applies a high luster to hard floor surfaces. 86306300 CHARIOT BURNISHER 11/09/07 Downloaded from www.Manualslib.com...
NOTE: If a service or option kit is installed on your machine, be sure to keep the KIT INSTRUCTIONS which came with the kit. It contains replacement parts numbers needed for ordering future parts. 86306300 CHARIOT BURNISHER 11/09/07 Downloaded from www.Manualslib.com manuals search engine...
This appliance has been designed for use with the high speed burnishing pads intended for wax finishes. The fitting of other pads may affect its safety. Do not use on surfaces having a gradient of over 10% (6 degrees). SAVE THESE INSTRUCTIONS 86306300 CHARIOT BURNISHER 11/09/07 Downloaded from www.Manualslib.com manuals search engine...
Always wear eye protection and protective clothing when working on or near batteries. Avoid skin contact with the acid contained in the batteries. Never allow metal to lie across battery tops. 86306300 CHARIOT BURNISHER 11/09/07 Downloaded from www.Manualslib.com manuals search engine...
NOTE: These drawings indicate the location of safety labels on the machine. If at any time the labels become illegible, promptly replace them. 86244310 PRV NO. 500956 CAUTION LABEL 86243830 (2) PRV NO. 500663 PINCH CAUTION 86252520 PRV NO. 80885 BATTERY CAUTION 86306300 CHARIOT BURNISHER 11/09/07 Downloaded from www.Manualslib.com manuals search engine...
Electrical parking brake, sets automatically whenever operator steps off platform or engages emergency stop. Minimum aisle u-turn width 56 in. (1425 mm) Maximum rated climb and descent angle 7.5 degrees 86306300 CHARIOT BURNISHER 11/09/07 Downloaded from www.Manualslib.com manuals search engine...
Page 9
This appliance contains no floor. The measurement and related calculations were possible source of impact noise. The instantaneous made in accordance with ANSI S3.34-1986. sound pressure level is below 63 Pa. 86306300 CHARIOT BURNISHER 11/09/07 Downloaded from www.Manualslib.com manuals search engine...
HOW THIS MACHINE WORKS The Chariot is a battery powered, self propelled, The function of the operator control system is to hard floor burnisher intended for commercial use. control the direction and speed of the machine. The The appliance spins a high-speed burnishing pad in...
Page 13
This safety feature is designed to ensure that the operator has their left foot on pedal platform whenever machine is moving. The operator must have left foot on Operator Presence Pedal for machine to move. 86306300 CHARIOT BURNISHER 11/09/07 Downloaded from www.Manualslib.com...
Page 14
HORN BUTTON The horn is activated by pressing the horn button. STEERING WHEEL The steering wheel turns the front wheel causing the machine to change direction. 86306300 CHARIOT BURNISHER 11/09/07 Downloaded from www.Manualslib.com manuals search engine...
Page 15
11. HOUR METER-BASIC Records the number of hours the machine has been in operation. This information is useful in determining when to service the machine. 86306300 CHARIOT BURNISHER 11/09/07 Downloaded from www.Manualslib.com manuals search engine...
Page 16
BURNISHER CONTROLS 3. Pad Pressure Meter 1. Pad Adjustment Knob 2. Burnisher Head Switch 86306300 CHARIOT BURNISHER 11/09/07 Downloaded from www.Manualslib.com manuals search engine...
Page 17
The motor will run only when the head is down and the machine is propelling. 3. PAD PRESSURE METER Indicates relative pad pressure. “Blue area” indicates proper pad pressure range. 3-10 86306300 CHARIOT BURNISHER 11/09/07 Downloaded from www.Manualslib.com manuals search engine...
This will also engage 7. Press the Drive Reset Switch. the parking brake and cause the machine to stop immediately. 8. Press lightly on the throttle pedal with right foot. 86306300 CHARIOT BURNISHER 11/09/07 3-11 Downloaded from www.Manualslib.com manuals search engine...
3. Check position of Directional Control Switch to ensure that machine is set to travel in direction INEFFICIENT BURNISHING PATH intended. 4. Press the Drive Reset Switch. RECOMMENDED BURNISHING PATH 86306300 CHARIOT BURNISHER 11/09/07 3-12 Downloaded from www.Manualslib.com manuals search engine...
Clean pivot points on burnishing head. Check drive motor for carbon brush wear. Check steering chain tension. NOTE: The pad drive motor contains no carbon brushes and requires no service. 86306300 CHARIOT BURNISHER 11/09/07 Downloaded from www.Manualslib.com manuals search engine...
Page 22
5. Ensure that all connections are tight and all corrosion removed. 6. Every 4 to 6 months, remove that batteries from the machine and clean the battery cases and battery compartment. 86306300 CHARIOT BURNISHER 11/09/07 Downloaded from www.Manualslib.com manuals search engine...
Page 23
10°F (6°C) below 80°F (27°C). of the electrolyte may cause an overflow resulting in a loss of battery acid balance and damage the machine. 86306300 CHARIOT BURNISHER 11/09/07 Downloaded from www.Manualslib.com manuals search engine...
Page 24
11. Install the rear cover. Attach suitable battery lifting device and lift batteries from the machine. Batteries are a potential environmental hazard. Consult your battery supplier for safe disposal methods. REAR OF MACHINE 86306300 CHARIOT BURNISHER 11/09/07 Downloaded from www.Manualslib.com manuals search engine...
1. Remove skirt strips by pulling down. 2. Insert new skirt strips and snap them into place. PAD CENTERING TOOL SNAP OUT SNAP IN CENTER LOCK 86306300 CHARIOT BURNISHER 11/09/07 Downloaded from www.Manualslib.com manuals search engine...
Attach metal ring (86082070 – PRV NO. 629000) using same screws that held pad lock keeper. Screw in spacer (862454470 – PRV NO. 739000) into motor shaft. 86306300 CHARIOT BURNISHER 11/09/07 Downloaded from www.Manualslib.com manuals search engine...
Page 28
Install clevis and rue ring. Turn machine on, raise deck, drive machine check that machine is working properly. If not recheck actuator barrel and reset again if needed. 86306300 CHARIOT BURNISHER 11/09/07 Downloaded from www.Manualslib.com manuals search engine...
60±5 amps. 2. Moving the wire in the slot, adjust the pad pressure meter until the needle sets at the line between the blue and red areas. 4-10 86306300 CHARIOT BURNISHER 11/09/07 Downloaded from www.Manualslib.com manuals search engine...
MAINTENANCE-DRIVE MOTOR & BRAKE Drive motor Parking brake Drive chain 86306300 CHARIOT BURNISHER 10/29/08 4-11 Downloaded from www.Manualslib.com manuals search engine...
Page 31
Machine can be pushed or towed (slowly). 2. Push lever firmly in direction of arrow Note: There is an intermediate stop. Make sure lever is fully in the down position. 86306300 CHARIOT BURNISHER 10/29/08 4-12 Downloaded from www.Manualslib.com manuals search engine...
Page 32
SMALL PIN OR SCREW 5. Remove brush cap. 6. Release brush from spring tension. Remove screw connecting brush wire lead to brush holder. Clean brush holder to insure free movement. 86306300 CHARIOT BURNISHER 11/09/07 4-13 Downloaded from www.Manualslib.com manuals search engine...
If fuse is blown, it must be replaced. be found and corrected. The fuse is located inside the battery compartment. 30 Amp. Protects the propel motor. 3 Amp. Protects the machine controls. (Basic only). 86306300 CHARIOT BURNISHER 11/09/07 4-14 Downloaded from www.Manualslib.com manuals search engine...
Check pad motor relay Deck vibrates Pad off center Re-center or replace pad using pad install tool Dust leaks from skirts Dust hose blocked Check for blockage and clear if needed 86306300 CHARIOT BURNISHER 11/09/07 4-15 Downloaded from www.Manualslib.com manuals search engine...
Page 35
1. Main contactor welded or stuck open. 2. Main contactor driver fault. 3. Brake coil resistance too high. MAIN ON FAULT main contactor driver On 1. Main contactor driver failed fault closed. 4-16 86306300 CHARIOT BURNISHER 05/27/08 Downloaded from www.Manualslib.com manuals search engine...
Page 36
EEPROM fault 1. EEPROM failure or fault. POWER SECTION FAULT power section fault 1. EEPROM failure or fault. 2. Short in motor or in motor wiring. 3. Controller failure. 86306300 CHARIOT BURNISHER 05/27/08 4-17 Downloaded from www.Manualslib.com manuals search engine...
Page 37
BURNISHER PARTS 86306300 CHARIOT BURNISHER 11/09/07 Downloaded from www.Manualslib.com manuals search engine...
Page 51
PLATE VERTICAL SUPPORT 86074160 270101 CHANNEL, RIGHT DELUXE 86073500 270090 BRKT, SIDE CHANNEL L 86277460 70847 SCR, 5/16-18 X 5/8 BSHCS SS 86238450 36245 GROMMET, 3.0 ID X 3.25 GROOVE 86306300 CHARIOT BURNISHER 11/09/07 5-14 Downloaded from www.Manualslib.com manuals search engine...
Page 53
SCR, 1/4-20 X 1 HHCS GR5 PLTD 86254280 730331 SPACER, 1.00 OD X .321ID X .375 86250250 66286 PLUSNUT, 1/4-20 FLATHEAD 86279630 87212 WASHER, .344 ID X 1.13 OD X .09 T PLT 86306300 CHARIOT BURNISHER 12/22/08 5-16 Downloaded from www.Manualslib.com manuals search engine...
Page 57
COTTER, 1/2” RING 86256130 730402 STRAP, STATIC, .2T X 1W X 3L 86276980 70775 SCR, 5/16 X 2 HHCS SS 86279630 87212 WASHER, .344ID X 1.13 OD X .09T PLT 86306300 CHARIOT BURNISHER 11/09/07 5-20 Downloaded from www.Manualslib.com manuals search engine...
Page 63
PIVOT, PAD ADJUST, L/H THD 86253270 730349 SHAFT, PAD ADJ, LOWER 86272010 57310 NUT, 3/8-24 LH THN HEX SS *SEE SERIAL NUMBER PAGE ** CALL MANUFACTURER FOR SERIAL NUMBER 86306300 CHARIOT BURNISHER 12/13/08 5-26 Downloaded from www.Manualslib.com manuals search engine...
3A BLU 9 BLK TO GND TERMINAL 4A RED 64 BLK 7 WHT/GRN 68 RED TO CONTROL PANEL 61 BLK 60 RED 65 BLK 67 RED SHOWS OPTIONAL EQUIPMENT 86306300 CHARIOT BURNISHER 12/22/08 5-45 Downloaded from www.Manualslib.com manuals search engine...
Page 83
880445 WIRE, 4X36 RD 5/16 RING 86010860 880353 WIRE, 4X20 BK CTERM X 5/16 RING 86260580 880443 WIRE, 4X12 RD 5/16 RING 86261210 29204 DIODE ASM, 76008 X 76008 86306300 CHARIOT BURNISHER 11/09/07 5-46 Downloaded from www.Manualslib.com manuals search engine...
Need help?
Do you have a question about the CB20 and is the answer not in the manual?
Questions and answers