1. Manuals
  2. Brands
  3. Supero Manuals
  4. Motherboard
  5. X6DAL-G
  6. User manual

Supero X6DAL-G User Manual

Hide thumbs
Table of Contents

Advertisement

Quick Links

Download this manual
S
®
UPER
SUPER X6DAL-G
SUPER X6DAL-TG
USER'S MANUAL
Revision 1.0a

Advertisement

Table of Contents
loading

Related Manuals for Supero X6DAL-G

Summary of Contents for Supero X6DAL-G

  • Page 1 ® UPER SUPER X6DAL-G SUPER X6DAL-TG USER’S MANUAL Revision 1.0a...
  • Page 2 The information in this User’s Manual has been carefully reviewed and is believed to be accurate. The vendor assumes no responsibility for any inaccuracies that may be contained in this document, makes no commitment to update or to keep current the information in this manual, or to notify any person or organization of the updates.

  • Page 3: Manual Organization

    Preface About This Manual This manual is written for system integrators, PC technicians and knowledgeable PC users. It provides information for the installation and use of the X6DAL-G/X6DAL-TG motherboard. The X6DAL- ® G/X6DAL-TG supports single or dual Intel Xeon Nocona processors at a 800 MHz front side bus.

  • Page 4: Table Of Contents

    Checklist ....................1-1 Contacting Supermicro ................1-2 X6DAL-G/X6DAL-TG Image ..........1-3 X6DAL-G/X6DAL-TG Layout ..........1-4 X6DAL-G/X6DAL-TG Quick Reference ......1-5 Motherboard Features ................1-6 Intel Lindenhurst Chipset: System Block Diagram ......1-8 Chipset Overview ................... 1-9 Special Features ..................... 1-9 BIOS Recovery ..................
  • Page 5 Table of Contents Power Fail LED ..................2-9 Reset Button ................... 2-10 Power Button ..................2-10 Chassis Intrusion ................... 2-10 Universal Serial Bus (USB0/1) ............2-10 Extra Universal Serial Bus Headers (USB2/3) ......... 2-11 Serial Ports ..................... 2-11 GLAN (Ethernet Port) ................2-11 ATX PS/2 Keyboard and Mouse Ports ..........
  • Page 6 X6DAL-G/X6DAL-TG User's Manual Technical Support Procedures ..............3-2 Frequently Asked Questions ................ 3-3 Returning Merchandise for Service ............3-5 Chapter 4: BIOS Introduction ....................... 4-1 Main BIOS Setup ....................4-2 Advanced Setup ....................4-3 Boot Setup ...................... 4-19 Security Setup ....................4-22 Exit ........................

  • Page 7: Chapter 1: Introduction

    One (1) Supermicro Mainboard One (1) ribbon cable for IDE devices (CBL-036) One (1) floppy ribbon cable (CBL-022) One (1) SATA cable (CBL-044) (*X6DAL-G) Four (4) SATA cables (CBL-044) (*X6DAL-TG) One (1) CPU mounting plate (SKT-159) Two (2) CPU retention brackets (SKT-158: pre-installed)

  • Page 8: Contacting Supermicro

    X6DAL-G/X6DAL-TG User's Manual Contacting Supermicro Headquarters Address: SuperMicro Computer, Inc. 980 Rock Ave. San Jose, CA 95131 U.S.A. Tel: +1 (408) 503-8000 Fax: +1 (408) 503-8008 Email: marketing@supermicro.com (General Information) support@supermicro.com (Technical Support) Web Site: www.supermicro.com Europe Address: SuperMicro Computer B.V.

  • Page 9: X6Dal-G/X6Dal-Tg Image

    Chapter 1: Introduction Figure 1-1. SUPER X6DAL-G/X6DAL-TG Image (*The difference between the X6DAL-G and the X6DAL-TG is that the X6DAL-TG has an additional 4-port SATA2 Marvell Controller.)
  • Page 10 Enable Spkr Notes: 1. " " indicates Pin 1. 2. The differences between the X6DAL-G and the X6DAL-TG are: * Marvell's SATA2 controller is available on the X6DAL-TG only. * There are additional four SATA2 ports (using Marvell's SATA2 controller) on the X6DAL-TG.
  • Page 11 Chapter 1: Introduction Quick Reference ( X6DAL-G/X6DAL-TG) Jumper Description Default Setting Alarm Reset Open (Disabled) SMB Data to PCI Enable Closed (Enabled) SMB Clock to PCI Enable Closed (Enabled) Audio Enable Closed (Enabled) JBT1 Clear CMOS See Chapter 2 Force Power On Enable...

  • Page 12: Motherboard Features

    +12V, 3.3V standby, and DIMM voltage. • Fan status monitor with fan speed control via BIOS • CPU/chassis temperature monitors • Environmental temperature monitor and control via Supero Doctor III • CPU fan auto-off in sleep mode • CPU slow-down on temperature overheat •...
  • Page 13 Chapter 1: Introduction ACPI Features • Microsoft OnNow • Slow blinking LED for suspend state indicator • Main switch override mechanism Onboard I/O • 1 Intel 82541PI Gigabit Ethernet controller • 2 EIDE Ultra DMA/100 bus master interfaces • 1 floppy port interface (up to 2.88 MB) •...
  • Page 14 X6DAL-G/X6DAL-TG User's Manual Figure 1-9. Block Diagram of the E7525 Tumwater Chipset Note: This is a general block diagram. Please see the previous Motherboard Features pages for details on the features of each motherboard.

  • Page 15: Chipset Overview

    Chipset Overview Built upon the functionality and the capability of the E7525 Tumwater chipset, the X6DAL-G/X6DAL-TG motherboard provides the performance and feature set required for dual processor-based servers, with configura- tion options optimized for communications, presentation, storage, computa- tion or database applications. The Intel E7525 Tumwater chipset consists...

  • Page 16: Special Features

    Always On. PC Health Monitoring This section describes the PC health monitoring features of the SUPER X6DAL-G/X6DAL-TG. All have an onboard System Hardware Monitor chip that supports PC health monitoring. Onboard Voltage Monitors for the CPU Cores, Chipset Voltage, +3.3V, +5V, +12V, -12v, +3.3V Standby, +2.5V (for...
  • Page 17 Chapter 1: Introduction Environmental Temperature Control via Supero DoctorIII The thermal control sensor monitors the CPU temperature in real time and will increase the speed of the thermal control fan whenever the CPU tem- perature exceeds a user-defined threshold. The overheat circuitry runs independently from the CPU.

  • Page 18: Acpi Features

    X6DAL-G/X6DAL-TG User's Manual ACPI Features ACPI stands for Advanced Configuration and Power Interface. The ACPI specification defines a flexible and abstract hardware interface that pro- vides a standard way to integrate power management features throughout a PC system, including its hardware, operating system and application soft- ware.

  • Page 19: Power Supply

    It is even more important for processors that have high CPU clock rates. The SUPER X6DAL-G/X6DAL-TG accommodates ATX power supplies. Al- though most power supplies generally meet the specifications required by the CPU, some are inadequate. You should use one that will supply at least 400W of power.

  • Page 20: Super I/O

    X6DAL-G/X6DAL-TG User's Manual Super I/O The disk drive adapter functions of the Super I/O chip include a floppy disk drive controller that is compatible with industry standard 82077/765, a data separator, write pre-compensation circuitry, decode logic, data rate selec- tion, a clock generator, drive interface control logic and interrupt and DMA logic.

  • Page 21: Chapter 2: Installation

    Chapter 2: Installation Chapter 2 Installation Static-Sensitive Devices Electric-Static-Discharge (ESD) can damage electronic components. To pre- vent damage to your system board, it is important to handle it very carefully. The following measures are generally sufficient to protect your equipment from ESD.

  • Page 22: Pga Processor And Heatsink Installation

    Make sure that you install the processor into the CPU socket before you install the CPU heatsink. Note that for the X6DAL-G/X6DAL-TG you need to install the Xeon mounting plate under the board. Installing the CPU Mounting Plate...
  • Page 23 Chapter 2: Installation 2. Insert the CPU in the socket, making sure that pin 1 of the CPU aligns with pin 1 of the socket (both corners are marked with a triangle). When using only one CPU, install it into CPU socket #1 Pin1 (Socket #2 is automatically disabled if only one CPU is used).
  • Page 24 X6DAL-G/X6DAL-TG User's Manual 1. Unscrew and remove the heatsink screws from the motherboard in the sequence as show in the second picture on the right. 2. Hold the heatsink as show in the picture on the right and gently wriggle the heatsink to loosen it from the CPU.

  • Page 25: Installing Dimms

    Repeat for all modules (see step 1 above). Memory Support The X6DAL-G/X6DAL-TG supports up to 12GB/24GB of Reg. ECC DDR 333/ 266 (PC2700/PC2100) memory. All motherboards were designed to support 4GB (PC2100) modules in each slot, but only the 2GB modules are tested.

  • Page 26: I/Oports/Control Panel Connectors

    X6DAL-G/X6DAL-TG User's Manual Figure 2-2. Installing and Removing DIMMs To Install: Insert module vertically and press down until it snaps into place. Pay attention to the alignment notch at the bottom. To Remove: Use your thumbs to gently push near...

  • Page 27: Power Led

    Chapter 2: Installation Front Control Panel JF1 contains header pins for various buttons and indicators that are nor- mally located on a control panel at the front of the chassis. These connec- tors are designed specifically for use with Supermicro server chassis. See Figure 2-4 for the descriptions of the various control panel buttons and LED indicators.
  • Page 28 X6DAL-G/X6DAL-TG User's Manual Connecting Cables ATX Power Supply 24-pin Connector Pin Definitions (PW1) Pin Number Definition Pin Number Definition +3.3V +3.3V ATX Power Connector +3.3V -12V There are a 24-pin main power PS_ON# supply connector(PW1) and a 4- pin 12V PWR connector (PW3) on...
  • Page 29 Chapter 2: Installation NMI Button NMI Button Pin Definitions (JF1) The non-maskable interrupt button header is located on pins 19 and Number Definition Control 20 of JF1. Refer to the table on Ground the right for pin definitions. Power LED PWR_LED Pin Definitions The Power LED connection is lo- (JF1)

  • Page 30: Nic1 Led Indicators

    X6DAL-G/X6DAL-TG User's Manual HDD LED HDD LED Pin Definitions The HDD LED connection is located (JF1) on pins 13 and 14 of JF1. Attach Number Definition the hard drive LED cable here to HD Active display disk activity (for any hard drives on the system, including SCSI, Serial ATA and IDE).
  • Page 31 Chapter 2: Installation Overheat/Fan Fail LED Overheat/Fan Fail LED Pin Definitions (JF1) Connect an LED to the OH/Fan Fail Number Definition connection on pins 7 and 8 of JF1 to provide advanced warning of chassis overheating. Refer to the table on the right for pin defini- Overheat/Fan Fail tions.

  • Page 32: Reset Button

    X6DAL-G/X6DAL-TG User's Manual Reset Button Reset Pin Definitions The Reset Button connection is lo- (JF1) cated on pins 3 and 4 of JF1. At- Number Definition tach it to the hardware reset Reset Ground switch on the computer case. Refer to the table on the right for pin definitions.

  • Page 33: Chassis Intrusion

    Chapter 2: Installation Chassis Intrusion Chassis Intrusion Pin Definitions A Chassis Intrusion header is lo- Number Definition cated at JL1. Attach the appropri- Intrusion Input Ground ate cable to inform you of a chas- sis intrusion. USB Pin Definition Universal Serial Bus (USB) USB O/1 (Back Panel USB) Pin# Definition There are two...
  • Page 34 Clock on the right for pin definitions.) Fan Headers There are six fan headers (Fan 1 to Fan 6) on the X6DAL-G/TG). 4-pin Fan Header Pin Definitions See the table on the right for pin (CPU and Chassis Fans )

  • Page 35: Serial Ports

    Chapter 2: Installation Serial Ports Serial Port Pin Definitions (COM1, COM2) The COM1 (J4) and COM2 (J5) se- Pin Number Definition Pin Number Definition rial ports are located under the parallel port (see Figure 2-3). See Serial In G round the table on the right for pin defini- Serial Out tions.

  • Page 36: Glan (Ethernet Port)

    X6DAL-G/X6DAL-TG User's Manual Wake-On-LAN Wake-On-LAN Pin The Wake-On-LAN header(JWOL) Definitions (JWOL) is designated WOL on the mother- Number Definition board. See the table on the right +5V Standby Ground for pin definitions. You must en- Wake-up able the LAN Wake-Up setting in BIOS to use this function.

  • Page 37: Power Fault

    Chapter 2: Installation Power Fault Power Fault Pin Definitions Connect a cable from your power Number Definition supply to the Power Fault header P/S 1 Fail Signal (J7) to provide warning of power P/S 2 Fail Signal P/S 3 Fail Signal supply failure.
  • Page 38 X6DAL-G/X6DAL-TG User's Manual SMB Power (I SMB PWR Connector Pin Definitions (J27) Pin # Definition C Connector Clock (J27), located be- SMB Data tween the Alarm Reset Header and the PWR Fault Header, moni- tors the status of PWR Supply, Fan and system temperature.
  • Page 39 Chapter 2: Installation AC 97/AUX In/CD In AC'97 provides high quality onboard Line In (surround L/R) Blue: audio. The X6DAL-G/X6DAL-TG fea- tures 6-channel sound for front L&R, Green: Line Out (Front L/R) rear L&R, center and subwoofer speakers. This feature is activated...

  • Page 40: Jumper Settings

    X6DAL-G/X6DAL-TG User's Manual Jumper Settings Explanation of Jumpers Connector Pins To modify the operation of the motherboard, jumpers can be used choose between Jumper optional settings. Jumpers create shorts between two pins to change the function of the Setting connector. Pin 1 is identified...

  • Page 41: Alarm Reset

    Chapter 2: Installation Alarm Reset Alarm Reset Jumper The system will notify you in the Settings event of a power supply failure. Jumper This feature assumes that Super- Position Definition micro redundant power supply Open Enabled Closed Disabled units are installed in the chassis. If you only have a single power supply installed, you should dis- able this (the default setting) with...

  • Page 42: Cmos Clear

    X6DAL-G/X6DAL-TG User's Manual CMOS Clear JBT1 is used to clear CMOS. Instead of pins, this "jumper" consists of contact pads to prevent the accidental clearing of CMOS. To clear CMOS, use a metal object such as a small screwdriver to touch both pads at the same time to short the connection.
  • Page 43 Chapter 2: Installation Audio Enable/Disable Audio Enable/Disable Jumper Settings J26 enables or disables the Audio (J26) Connector on the motherboard. Jumper Position Definition See the table on the right for Pins 1-2 Enabled Pins 2-3 Disabled jumper settings. The default set- ting is enabled.

  • Page 44: Onboard Indicators

    X6DAL-G/X6DAL-TG User's Manual Onboard Indicators G-bit LAN Right LED Indicator GLAN LEDs Color Definition No Connection Green 100 MHz The Gigabit Ethernet LAN port (lo- Orange 1 GHz cated beside the COM Port2) has two LEDs. The yellow LED indi-...
  • Page 45 PW R LED indicators (DS1-DS3, DS5-DS8 ) CPU Overheat DS7-8 POST LED on the X6DAL-G/TG. See the table on the right for speaker pin defini- tions. (*Note: Please refer to Ap- pendix A for DS7 and DS8 LED POST Codes.)

  • Page 46: Parallel Port, Floppy/Hard Disk Drive And Scsi Connections

    X6DAL-G/X6DAL-TG User's Manual Parallel Port, Floppy/Hard Disk Drive and SCSI Connections Note the following when connecting the floppy and hard disk drive cables: • The floppy disk drive cable has seven twisted wires. • A red mark on a wire typically designates the location of pin 1.

  • Page 47: Floppy Connector

    Chapter 2: Installation Floppy Connector Floppy Connector Pin Definitions (J24) Pin Number Function Pin Number Function The floppy connector is located FDHDIN Reserved on J24. See the table below for FDEDIN pin definitions. Index- Motor Enable Drive Select B- Drive Select A- Motor Enable DIR- STEP-...

  • Page 48: Ide Connectors

    X6DAL-G/X6DAL-TG User's Manual IDE Connectors IDE Connector Pin Definitions (J44, J38) The IDE Connectors are lo- Pin Number Function Pin Number Function cated on J44 (IDE1) and J38 Reset IDE Host Data 7 Host Data 8 (IDE 2), You do not need to...

  • Page 49: Chapter 3: Troubleshooting

    Chapter 3: Troubleshooting Chapter 3 Troubleshooting Troubleshooting Procedures Use the following procedures to troubleshoot your system. If you have followed all of the procedures below and still need assistance, refer to the ‘Technical Support Procedures’ and/or ‘Returning Merchandise for Service’ section(s) in this chapter.

  • Page 50: Memory Errors

    X6DAL-G/X6DAL-TG User's Manual NOTE If you are a system integrator, VAR or OEM, a POST diagnos- tics card is recommended. For I/O port 80h codes, refer to App. B. Memory Errors 1. Make sure the DIMM modules are properly and fully installed.

  • Page 51: Frequently Asked Questions

    Question: What are the various types of memory that my mother- board can support? Answer: The X6DAL-G/X6DAL-TG has six 184-pin DIMM slots that support registered ECC DDR 333/266 (PC2700/2100) SDRAM modules. It is strongly recommended that you do not mix memory modules of different speeds and sizes.

  • Page 52: Returning Merchandise For Service

    X6DAL-G/X6DAL-TG User's Manual Question: What's on the CD that came with my motherboard? Answer: The supplied compact disc has quite a few drivers and programs that will greatly enhance your system. We recommend that you review the CD and install the applications you need. Applications on the CD include chipset drivers for Windows and security and audio drivers.

  • Page 53: Chapter 4: Ami Bios

    Chapter 4 AMIBIOS Introduction This chapter describes the AMIBIOS for the X6DAL-TG/X6DAL-G. The AMI ROM BIOS is stored in a Flash EEPROM and can be easily upgraded using a floppy disk-based program. This chapter describes the basic navigation of the AMI BIOS Setup Utility setup screens.

  • Page 54: Main Bios Setup

    X6DAL-G/X6DAL-TG User’s Manual 4-2 Main Setup When you first enter the AMI BIOS Setup Utility, you will enter the Main setup screen. You can always return to the Main setup screen by selecting the Main tab on the top of the screen. The Main BIOS Setup screen is shown below.

  • Page 55: Advanced Settings

    Chapter 4: AMI BIOS System Memory This option allows the AMI BIOS to display the status of memory installed in the system. Size This option allows the AMI BIOS to display the size of memory installed in the system. System Time/System Date Use this option to change the system time and date.
  • Page 56 X6DAL-G/X6DAL-TG User’s Manual ! ! ! ! ! CPU Configuration Sub Menu Configure Advanced CPU Settings This option allows the user to configure Advanced CPU settings for the processor(s) installed in the system. Ratio CMOS Setting This option allows the user to set the ratio between the CPU Core Clock and the FSB Frequency.
  • Page 57 Chapter 4: AMI BIOS ! ! ! ! ! IDE Configuration Sub Menu The screen for the Primary IDE Master is shown below: When you select this Sub Menu, the AMI BIOS automatically displays the status of the following items: Onboard PCI IDE Operate Mode This feature allows the user to set the Onboard PCI IDE Operation Mode.
  • Page 58 X6DAL-G/X6DAL-TG User’s Manual S-ATA Ports Definition This feature allows the user to configure Serial ATA Ports. The options are: P0-Master/P1-Slave, P0-Slave/P1-Master P-ATA Only S-ATA Running Enhanced Mode Select Yes if you want the function of Serial ATA Enanced Mode to be enabled at all times.
  • Page 59 Chapter 4: AMI BIOS LBA/Large Mode LBA (Logical Block Addressing) is a method of addressing data on a disk drive. In the LBA mode, the maximum drive capacity is 137 GB. For drive capacities over 137 GB, your system must be equipped with 48-bit LBA mode addressing.
  • Page 60 X6DAL-G/X6DAL-TG User’s Manual to allow the BIOS to use Single Word DMA mode 0. It has a data transfer rate of 2.1 MBs. Select SWDMA1 to allow the BIOS to use Single Word DMA mode 1. It has a data transfer rate of 4.2 MBs. Select SWDMA2 to allow the BIOS to use Single Word DMA mode 2.

  • Page 61: Floppy Configuration

    Chapter 4: AMI BIOS ATA(PI) 80Pin Cable Detection This feature allows the AMI BIOS to auto-detect 80Pin ATA(PI) Cable. The options are: Host & Device, Host and Device. ! ! ! ! ! Floppy Configuration This option allows the user to configure the settings for the Floppy Drives installed in the system.
  • Page 62 X6DAL-G/X6DAL-TG User’s Manual PCI/PnP Configuration This feature allows the user to set PCI/PnP configurations for the following items: Plug & Play OS Select Yes to allow the OS to configure Plug & Play devices. (*This is not required for system boot if you system has an OS that supports Plug &...
  • Page 63 Chapter 4: AMI BIOS IRQ3/IRQ4/IRQ5/IRQ7/IRQ9/IRQ10/IRQ11/IRQ14 This feature specifies the availability of an IRQ to be used by a PCI, PnP device. Select Reserved for the IRQ to be used by a Legacy ISA device. The options are: Available, Reserved. DMA Channel 0/DMA Channel 1/DMA Channel 3/DMA Channel 5/ DMA Channel 6/DMA Channel 7 Select Available to indicate that a specific DMA channel is available to be used by a PCI/PnP device.

  • Page 64: Advanced Chipset Settings

    X6DAL-G/X6DAL-TG User’s Manual Serial Port1 Address This option specifies the base I/O port address and Interrupt Request ad- dress of serial port 1. Select "Disabled" to prevent the serial port from accessing any system resources. When this option is set to Disabled, the serial port physically becomes unavailable.

  • Page 65: Northbridge Configuration

    Chapter 4: AMI BIOS !NorthBridge Configuration This feature allows the user to configure the settings for Intel Lindenhurst NorthBridge chipset. Memory Remap Feature Select Enabled to allow remapping of overlapped PCI memory above the total physical memory. The options are Enabled and Disabled. Memory Mirroring and Sparing Select Enabled to enable Memory RAS (-Mirroring and Sparing) to allow the system to create a mirror copy of data written to the memory for data...
  • Page 66 X6DAL-G/X6DAL-TG User’s Manual ! ! ! ! ! APCI Configuration This item allows the user to enable or disable ACPI support for the operating system. General ACPI Configuration Use this feature to configure additional ACPI options. Select "Yes" if the operating system supports ACPI.

  • Page 67: Power Configuration

    Chapter 4: AMI BIOS Power Configuration This feature allows the user to configure PnP settings. Power Button Mode This setting allows you to decide if the power button will go into the On/ Off mode or the Suspend mode if it is pressed. The options are On/Off and Suspend.

  • Page 68: Mps Configuration

    X6DAL-G/X6DAL-TG User’s Manual Memory Buffer Event Logging This setting allows you to enable or disable Memory Buffer Event logging. The options are Enabled or Disabled. PCI Error Logging This setting allows you to enable or disable PCI Error logging. The options are Enabled or Disabled.

  • Page 69: Remote Access Configuration

    Chapter 4: AMI BIOS Spread Spectrum Select Enabled to enable Spread Sperctrum. The options are Disabled and Enabled. !Remote Access Configuration You can use this screen to select options for the Remote Access Configu- ration. Use the up and down <Arrow> keys to select an item. Use the <Plus>...

  • Page 70: System Health Monitor

    X6DAL-G/X6DAL-TG User’s Manual USB 2.0 Controller Mode This setting allows you to configure USB 2.0 Controller Mode. The options are Hi-Speed (480 Mbps) or Full Speed-12Mbps. System Health Monitor This feature allows the AMI BIOS to automatically display the status of the...

  • Page 71: Boot Settings

    Chapter 4: AMI BIOS Fan Speed Control Modules: This feature allows the user to decide how the system controls the speeds of the onboard fans. If the option is set to "3-pin fan", the fan speed is controlled based upon the CPU die temperature. When the CPU die tempera- ture is higher, the fan speed will be higher as well.
  • Page 72 X6DAL-G/X6DAL-TG User’s Manual Quick Boot Select Enabled to allow the AMI BIOS to skip certain test during POST in order to shorten the time needed for the system to bootup. The options are Enabled, and Disabled. Quiet Boot Set this value to allow the boot up screen options to be modified between POST messages or OEM logo.

  • Page 73: Boot Device Priority

    Chapter 4: AMI BIOS Boot Device Priority This feature allows the user to specify the sequence of priority for the Boot Device. The settings are "1st Floppy Drive", "CD ROM", "HDD", and "Disabled." The default settings are: · 1st boot device –1st Floppy Drive ·...

  • Page 74: Security Settings

    X6DAL-G/X6DAL-TG User’s Manual Security Settings the AMI BIOS provides a Supervisor and a User password. If you use both passwords, the Supervisor password must be set first. Change Supervisor Password Select this option and press <Enter> to access the sub menu, and then, type in the password.

  • Page 75: Exit Options

    Chapter 4: AMI BIOS Exit Options Select the Exit tab from the AMI BIOS Setup Utility screen to enter the Exit the BIOS Setup screen. Saving Changes and Exit When you have completed the system configuration changes, select this option to leave the BIOS Setup and reboot the computer, so the new system configuration parameters can take effect.
  • Page 76 X6DAL-G/X6DAL-TG User’s Manual Load Optimal Defaults To set this feature, select Load Optimal Defaults from the Exit menu and press <Enter>. Then, Select "OK" to allow the BIOS to automatically load Optimal Defaults to the BIOS Settings. The Optimal settings are designed for maximum system performance, but may not work best for all computer ap- plications.

  • Page 77: Appendix Abios Error Beep Codes And Ds7/Ds8 Led Post Codes

    Appendix A: AMIBIOS Error Beep Codes Appendix A BIOS Error Beep Codes and DS7/DS8 LED POST Codes During the POST (Power-On Self-Test) routines, which are performed each time the system is powered on, errors may occur. Non-fatal errors are those which, in most cases, allow the system to continue the boot-up process.
  • Page 78 X6DAL-G/X6DAL-TG User’s Manual DS7/DS8 LED Post Codes LED Indicators Description/Message PWR On SPD Read OK Memory Size-OK Starting Bus Initialization...
  • Page 79 Appendix B: BIOS POST Checkpoint Codes Appendix B BIOS POST Checkpoint Codes When AMIBIOS performs the Power On Self Test, it writes checkpoint codes to I/O port 0080h. If the computer cannot complete the boot process, diagnostic equipment can be attached to the computer to read I/O port 0080h. Uncompressed Initialization Codes The uncompressed initialization checkpoint codes are listed in order of execution: Checkpoint...
  • Page 80 X6DAL-G/X6DAL-TG User’s Manual Bootblock Recovery Codes The bootblock recovery checkpoint codes are listed in order of execution: Checkpoint Code Description The onboard floppy controller if available is initialized. Next, beginning the base 512 KB memory test. Initializing the interrupt vector table next.
  • Page 81 Appendix B: BIOS POST Checkpoint Codes initialization before the keyboard BAT command is issued. The keyboard controller input buffer is free. Next, issuing the BAT command to the keyboard controller. The keyboard controller BAT command result has been verified. Next, performing any necessary initialization after the keyboard controller BAT command test.
  • Page 82 X6DAL-G/X6DAL-TG User’s Manual Checkpoint Code Description Interrupt vector initialization is done. Clearing the password if the POST DIAG switch is on. Any initialization before setting video mode will be done next. Initialization before setting the video mode is complete. Configuring the monochrome mode and color mode settings next.
  • Page 83 Appendix B: BIOS POST Checkpoint Codes Checkpoint Code Description Patterns written in base memory. Determining the amount of memory below 1 MB next. The amount of memory below 1 MB has been found and verified. Determining the amount of memory above 1 MB memory next. The amount of memory above 1 MB has been found and verified.
  • Page 84 X6DAL-G/X6DAL-TG User’s Manual Checkpoint Code Description The DMA page register test passed. Performing the DMA Controller 1 base register test next. The DMA controller 1 base register test passed. Performing the DMA controller 2 base register test next. The DMA controller 2 base register test passed. Programming DMA controllers 1 and 2 next.
  • Page 85 Appendix B: BIOS POST Checkpoint Codes Checkpoint Code Description Initializing the bus option ROMs from C800 next. See the last page of this chapter for additional information. Initializing before passing control to the adaptor ROM at C800. Initialization before the C800 adaptor ROM gains control has com- pleted.
  • Page 86 X6DAL-G/X6DAL-TG User’s Manual Notes...

  • Page 87: Operating System

    Appendix C: Software Installation Appendix C Installing Software Drivers and Windows Operating System After all the hardware has been installed, you must first configure the Adaptec Embedded Serial ATA RAID Driver before you install the Windows operating system. The necessary drivers are all included on the Supermicro bootable CDs that came packaged with your motherboard.
  • Page 88 RAID mirroring (RAID 1) allows the data to be simulta- neously written to two drives, so critical data is always available even if a single hard disk fails. Due to the built-in functionality, the X6DAL-G/ X6DAL-TG is specially designed to keep pace with the increasing...
  • Page 89 Appendix C: Software Installation Using the Adaptec RAID Configuration Utility (ARC) The Adaptec RAID Configuration Utility is an embedded BIOS Utility, including: *Array Configuration Utility: Use this utility when you want to create, configure and manage arrays. * Disk Utilities: Use this option to format or verify disks. To run the Adaptec RAID Configuration Utility, you will need to enable the RAID function in the system BIOS (refer to Chapter 4 for System BIOS Configurations), and then, press the <Ctrl>...
  • Page 90 X6DAL-G/X6DAL-TG User's Manual Managing Arrays Select this option to view array properties, and delete arrays. The following sections describe the operations Of "Managing Arrays". To select this option, use the arrow keys and the <enter> key to select "Managing Arrays" from the main menu (as shown above).
  • Page 91 Appendix C: Software Installation Viewing Array Properties To view the properties of an existing array: 1. At the BIOS prompt, press Ctrl+A. 2. From the ARC menu, select Array Configuration Utility (ACU). 3. From the ACU menu, select Manage Arrays (as shown on the previous screen.) 4.
  • Page 92 X6DAL-G/X6DAL-TG User's Manual Creating Arrays Before creating arrays, make sure the disks for the array are connected and installed in your system. Note that disks with no usable space, or disks that are un-initialized are shown in gray and cannot be used. See Initializing Disk Drives.
  • Page 93 Appendix C: Software Installation 5 Press Enter when both disks for the new array are selected. The Array Properties menu displays (as the screen shown below). Assigning Array Properties Once you've create a new array, you are ready to assign the properties to the array.
  • Page 94 X6DAL-G/X6DAL-TG User's Manual 2. Under the item "Arrays Label", type in an label and press Enter. (*Note: The label shall not be more than 15 characters.) 3. For RAID 0, select the desired stripe size. (*Note: Available stripe sizes are 16, 32, and 64 KB-default. It is recommended that you do not change the default setting.)
  • Page 95 Appendix C: Software Installation 5. When you are finished, press Done (as the screen shown below). Notes: 1. Before adding a new drive to an array, back up any data contained on the new drive. Otherwise, all data will be lost. 2.
  • Page 96 X6DAL-G/X6DAL-TG User's Manual Adding a Bootable Array To make an array bootable: 1. From the Main menu, select Manage Arrays. 2. From the List of Arrays, select the array you want to make bootable, and press Ctrl+B. 3. Enter Y to create a bootable array when the following message is displayed: "This will make all other existing bootable array non-bootable.

  • Page 97: Initializing Disk Drives

    Appendix C: Software Installation Initializing Disk Drives If an installed disk does not appear in the disk selection list for creating a new array, or if it appears grayed out, you may have to initialize it before you can use it as part of an array. Drives attached to the controller must be initialized before they can be used in an array.
  • Page 98 X6DAL-G/X6DAL-TG User's Manual 4. Use the up and down arrow keys to highlight the disk you wish to initialize and press Insert (as shown in the screen below). C-12...
  • Page 99 Appendix C: Software Installation 5. Repeat Step 4 so that both drives to be initialized are selected (as shown in the screen below). 6. Press Enter. 7. Read the warning message as shown in the screen. 8. Make sure that you have selected the correct disk drives to initialize. If correct, type Y to continue.
  • Page 100 X6DAL-G/X6DAL-TG User's Manual Rebuilding Arrays *Note 1: Rebuilding applies to Fault Tolerant array (RAID 1) only. If an array Build process (or initialization) is interrupted or critical with one member missing, you must perform a Rebuild to get the array to Optimal status.

  • Page 101: Using The Disk Utilities

    Appendix C: Software Installation Using the Disk Utilities The Disk Utilities enable you to format or verify the media of your Serial ATA hard disks. To access the disk utilities: 1. Turn on your computer and press Ctrl+A when prompted to access the ARC utility (as shown in the screen below.) C-15...
  • Page 102 X6DAL-G/X6DAL-TG User's Manual 2. From the ARC menu, select Disk Utilities as shown in the screen below. 3 Select the desired disk and press Enter (as shown in the screen below.) C-16...
  • Page 103 Appendix C: Software Installation You can choose from the following options: 1. Format Disk—Simulates a low-level format of the hard drive by writing zeros to the entire disk. Serial ATA drives are low-level formatted at the factory and do not need to be low-level formatted again. (*Caution: Formatting destroys all data on the drive.
  • Page 104 X6DAL-G/X6DAL-TG User's Manual C-2 Installing Intel's Hance Rapids Driver by Adaptec and the Windows OS a. Insert Supermicro's bootable CD that came with the package into the CD Drive during the system reboot, and the screen:"Super Micro Driver Diskette Maker" will appear.
  • Page 105 You should install everything here except for the Supero Doctor utility, Intel LDCM and the LAN/SCSI driver diskettes, which are optional. The bottom icon with a CD on it allows you to view the entire contents of the CD.
  • Page 106 X6DAL-G/X6DAL-TG User's Manual Supero Doctor III The Supero Doctor III program is a Web base management tool that supports remote management capability. It includes Remote and Local Management tools. The local management is called SD III Client. The Supero Doctor III program included on the CDROM that came with your motherboard allows you to monitor the environment and operations of your system.
  • Page 107 Supero Doctor III Interface Display Screen-II (Remote Control) (*Note: SD III Software Revision 1.0 can be downloaded from our Web site at: ftp://ftp.supermicro.com/utility/Supero_Doctor_III/. You can also download SDIII User's Guide at: http://www.supermicro.com/PRODUCT/ Manuals/SDIII/UserGuide.pdf. For Linux, we will still recommend Supero Doctor II.) C-21...
  • Page 108 X6DAL-G/X6DAL-TG User's Manual Notes C-22...
  • Page 109 Appendix D: Software Installation: Adaptec's SATA HostRAID Utility Appendix D Software Installation: Adaptec's SATA 88SX6041 Chip HostRAID Utility for Marvell's (*For X6DAL-TG only.) After all the hardware has been installed, you must first configure Adaptec's Serial ATA RAID Driver (*Note) before you install the Windows operating system, and other software drivers.
  • Page 110 X6DAL-G/X6DAL-TG User's Manual Operating Systems supported by the SATA RAID Host Controller Microsoft ® ® *Windows 2000, Windows Server 2003, and Windows XP Linux *Red Hat 8.0 and 9.0 *SuSE 8.1 and 8.2 Storage Management Software Overview Adaptec Embedded Serial ATA RAID includes the following software tools to manage your storage subsystem: Adaptec Storage Manager –...
  • Page 111 Appendix D: Software Installation: Adaptec's SATA HostRAID Utility 8. When the Adaptec Embedded Serial ATA HostRAID driver is found, press Enter. Follow the remaining on-screen instructions to complete your installation. Installing the Driver in an Existing Windows System Please follow the steps listed below to install a driver in a system that already has a Windows operating system: 1.
  • Page 112 X6DAL-G/X6DAL-TG User's Manual Installing the SuSE 8.1 or 8.2 Driver in a New Linux System 1. Obtain a driver disk from either the Web site or the product CD. 2. Restart the computer. 3. If creating an array, press Ctrl-A when prompted to enter the ARC utility.
  • Page 113 Appendix D: Software Installation: Adaptec's SATA HostRAID Utility D-3 Installing Adaptec Storage Management A. Browser Edition Overview This chapter discusses the installation procedure for installing Adaptec Storage Manager – Browser Edition to enable remote and local management of arrays. Browsers supported: To run Adaptec Storage Manager –...
  • Page 114 X6DAL-G/X6DAL-TG User's Manual B. On Windows **Note: When installing on a FAT 32 file system, the folder being installed is automatically hidden.) To install Adaptec Storage Manager – Browser Edition 1. Verify that a supported browser is installed. See the section-"Supported Browsers"...
  • Page 115 Appendix D: Software Installation: Adaptec's SATA HostRAID Utility Configuring Internet Explorer for Local Management When using the High security setting, you must enable the following settings manually: * JavaScript * Cookies (not stored) You do not need to enable the following custom level security settings for the local Intranet in Internet Explorer 5 and 5.5.
  • Page 116 X6DAL-G/X6DAL-TG User's Manual 6. You are now ready to proceed to C-4-"Using Adaptec Storage Manager – Browser Edition". Configuring Netscape Navigator for Remote Management If you know the IP address of the system you want to manage remotely: 1. Choose Edit> Preferences > Advanced> Proxies > Manual proxy configuration >...
  • Page 117 Appendix D: Software Installation: Adaptec's SATA HostRAID Utility D-4.Using Adaptec Storage Manager(-Browser Edition) Overview This chapter describes how to use Adaptec Storage Manager – Browser Edition to manage arrays. (*Note: Your controller may not support all of the features described. In most cases if a feature is not supported by your controller, the feature does not appear in the interface.) With Adaptec Storage Manager, you can:...
  • Page 118 X6DAL-G/X6DAL-TG User's Manual Logging In To login: 1. Start Adaptec Storage Manager – Browser Edition. * In Windows, click Start > Programs > Adaptec Storage Manager > Adaptec Storage Manager – Browser Edition. * In Linux, click Start > System > Adaptec Storage Manager.
  • Page 119 Appendix D: Software Installation: Adaptec's SATA HostRAID Utility Installing a Security Certificate If you chose not to install a security certificate when you installed Adaptec Storage Manager – Browser Edition, you must install the certificate when you run the application for the first time. To create the certificate: 1.
  • Page 120 X6DAL-G/X6DAL-TG User's Manual The action buttons are: * Logout—Selecting Logout ends your session and returns you to the Login screen. * Rescan—Used to rescan the configuration of the system. Typically, when a rescan is required, it occurs automatically; for example, after an array is created.
  • Page 121 Appendix D: Software Installation: Adaptec's SATA HostRAID Utility Physical Devices The Physical Devices view displays information about the drives and enclosures attached to the Adaptec RAID controller. The devices are shown organized by the channel or port that they are connected to and shown in numerical order.
  • Page 122 X6DAL-G/X6DAL-TG User's Manual When expanded, the Full Size Capacity View button and the Relative Size Capacity View button represent each drive as a bar. A drive that is not used as part of any array is shaded blue surrounded by a dotted line.
  • Page 123 Appendix D: Software Installation: Adaptec's SATA HostRAID Utility If a global hot spare exists, all arrays that the hot spare is large enough to protect will show as protected. In the expanded view, the icons for the arrays are arranged vertically and alongside them are the capacity, name, and type of array.
  • Page 124 X6DAL-G/X6DAL-TG User's Manual D-5 Adaptec RAID Configuration Utility The Array Configuration Utility (ACU) enables you to create, manage, and delete arrays from the controller’s BIOS, and initialize drives. A. Managing Arrays Select the Manage Arrays option to view array properties and members, and delete arrays.
  • Page 125 Appendix D: Software Installation: Adaptec's SATA HostRAID Utility B. Creating Arrays Before creating arrays, make sure the disks for the array are connected and installed in your system. Note that disks with no usable space, or disks that are not initialized are shown in gray and cannot be used. See Initializing Disk Drives.
  • Page 126 X6DAL-G/X6DAL-TG User's Manual (*Notes:) * Before adding a new drive to an array, back up any data contained on the new drive. Otherwise, all data will be lost. * If you stop the Build or Clear process on a RAID 1 or RAID 10 from ACU you can only restart it from Adaptec Storage Manager -Browser Edition.
  • Page 127 Appendix D: Software Installation: Adaptec's SATA HostRAID Utility Using the Disk Utilities The Disk Utilities enable you to format or verify the media of your Serial ATA hard disks. To access the disk utilities: 1. Turn on your computer and press Ctrl+A when prompted to access the ARC utility.
  • Page 128 X6DAL-G/X6DAL-TG User's Manual Notes D-20...

This manual is also suitable for:

X6dal-tg

Table of Contents