Table of Contents
Advertisement
Quick Links
Advertisement
Table of Contents
Subscribe to Our Youtube Channel
Related Manuals for Uniden EXP 8000 Series
Summary of Contents for Uniden EXP 8000 Series
- Page 1 UCZZ01630DZ...
- Page 2 • 7 Hours Talk Time • Hearing Aid Compatible The EXP 8000 Series features include AutoTalk and AutoStandby. AutoTalk allows you to answer a call by just removing the handset from the base so you don’t have to waste time pushing buttons or flipping switches.
-
Page 3: Controls And Functions
Controls and functions talk batt mute talk flash mute redial pqrs wxyz oper channel pause tone ringer e x t e n d e d r a n g e status in use page/find... -
Page 4: Status
Handset antenna 21. Handset retainer clip Headset jack cover 22. Base charging contacts Handset battery compartment 23. Base antenna Handset ringer switch 24. Status LED Handset earpiece 25. In use LED Talk/Battery LED 26. Page/Find key Talk key 27. Pulse/Tone switch Volume down key 28. -
Page 5: Table Of Contents
Getting Started Contents Introduction / Features....inside front cover Control and Functions....inside front cover Getting Started Read this first............2 Using your Step 1: Checking the package contents ....3 New Phone Step 2: Setting up the base unit ......4 Mounting the base unit on a wall ...7 Step 3: Charging the battery pack ......9 Adjusting the volume control....11 Using your New Phone... -
Page 6: Read This First
Read this first This cordless telephone must be set up before use. Follow these steps: Step 1 (page 3) Unpack and check the telephone and accessories. Step 2 (page 4 to 8) Next, choose the best location to set up the base unit. Base unit Step 3 (page 9 to 10) -
Page 7: Step 1: Checking The Package Contents
Checking the package contents Make sure you have received the following items in the package. If any of these items are missing or damaged, contact the Uniden Parts Department (see below). • Base unit • Handset • AC adapter (AD-310) •... -
Page 8: Step 2: Setting Up The Base Unit
Setting up the base unit Do the following steps. • Choose the best location • Connect the base unit • Choose the dialing mode Choose the best location Before choosing a location for your new phone, read the INSTALLATION CONSIDERATIONS included in the PRECAUTIONS AND IMPORTANT SAFETY INSTRUCTIONS brochure. - Page 9 (supplied) To telephone outlet To TEL LINE Telephone line cord (supplied) Use only the Uniden AC Connect the telephone line cord to the TEL LINE jack and to adapter supplied with this phone. Do NOT use an a telephone outlet.
-
Page 10: Choose The Dialing Mode
Use only the supplied AD-310 AC adapter. Do not use any other Polarity of the plug AC adapter. Connect the AC adapter to a continuous power supply. Place the base unit close to the AC outlet so that you can unplug the AC adapter easily. -
Page 11: Mounting The Base Unit On A Wall
Mounting the base unit on a wall Standard wall plate mounting This phone can be mounted on any standard telephone wall plate. Snap the wall mount adapter into the notches on the base. Plug the telephone line cord to the TEL LINE jack and the AC adapter to the DC IN 9V jack. - Page 12 On the base unit, pull the Handset retainer handset retainer out of the slot. Rotate it clockwise 180 degrees. Flip the retainer from front to back. Slide it back into the slot If you have wall mounted the base, you must remove so that the lip of the retainer is the beltclip to charge the up and the oval is down.
-
Page 13: Step 3: Charging The Battery Pack
Black aligned. Use only the Uniden Battery pack (model BT-905) supplied with your phone. Slide the battery cover forward until it snaps into place. Place the handset on the base. -
Page 14: When The Battery Charge Becomes Low
Battery use time (per charge) From fully charged Even when the battery • Seven hours coutinuous use. pack is not being used, it • Seven days when the handset is in the standby mode. will gradually discharge over a long period. -
Page 15: Adjusting The Volume Control
Adjusting the volume control Ringer Tone and Volume ª While the phone is not in use, press ringer The phone has two ringer tones, each with two volume levels. Press ringer until you hear the ringer tone and volume level you want. -
Page 16: Making And Receiving Calls
Making and receiving calls Handset On Base Handset Off Base Fold out the front cover of this owner’s manual to use the CONTROLS diagram for reference. To answer Pick up the handset. Press talk a call 1. Pick up the handset. 1. -
Page 17: Storing A Number In Memory
Storing a number in memory Your EXP 8000 Series phone has 10 memory locations for storing important telephone numbers. Remove the handset from the base You have 20 seconds after pressing each button. and press . The talk/batt Otherwise, an error tone LED flashes and you hear a beep. -
Page 18: Storing Mixed Tone/Pulse Number
Storing mixed tone/pulse number If your have selected pulse dialing, you can store a mixed tone/pulse number (up to 20 digits) for memory dialing. Remove the handset from the base and press . The talk/batt LED flashes and you hear a beep. Enter the number to be dialed in pulse mode. -
Page 19: Chain Dialing
You’ll hear a long beep confirming that the number is erased. Replacing a stored number Remember, your EXP 8000 Series phone has 10 memory locations, represented by the numbers (0-9) on the keypad. If you store a phone number in one of these locations, then attempt to store a different number in the same location later, the new number will replace the previous one. -
Page 20: Selecting A Different Channel
Selecting a different channel If you encounter interference while using your phone, you can manually change the phone’s channel for clear operation. Interference can come from appliances or other phones in your home. This function works only when the phone is in use. channel button on the handset allows you to choose between 30 different... -
Page 21: Mute
Mute Muting the ringer sound Press mute when the telephone rings. The ringer sound is cut off until you talk receive another call. Muting the conversation mute Press during a telephone call, the mute sound from the microphone is cut off. To cancel mute, press talk mute... -
Page 22: Changing The Digital Security Code
Changing the digital security code The digital security code is an identification code used to connect the handset and the base unit. Normally, setting the code is not necessary. The first time you charge your handset, the security code is automatically set. -
Page 23: Installing The Beltclip
Installing the beltclip To attach the beltclip To remove the beltclip Insert the beltclip into the Pull both sides of the beltclip holes on each side of the to release the tabs from handset. Press down until the holes. it clicks. If you have wall mounted the base, you must remove the beltclip to charge the... -
Page 24: Note On Power Sources
Note on power sources Battery replacement RECYCLING NICKEL- and handling CADMIUM BATTERIES When the operating time NICKEL- becomes short, even after a CADMIUM battery is recharged, please BATTERIES replace the battery. MUST BE With normal usage, your battery DISPOSED OF Ni-Cd should last about one year. -
Page 25: Troubleshooting
Troubleshooting If your phone is not performing to your expectations, please try these simple steps first. Symptom Suggestion The status LED won't • Make sure the AC adapter is plugged come on when the into the base unit and wall outlet. handset is placed in •... -
Page 26: Specifications
If you need any assistance with this product, please call our Customer Hotline at 1-800-297-1023 PLEASE DO NOT RETURN THIS PRODUCT TO THE PLACE OF PURCHASE. Our Uniden representatives will be happy to help you with any matters regarding the operation of this unit, available accessories, or any other related matters. -
Page 27: Index
Index Mounting the base unit to a wall........7 Adjusting the Mute ........17 volume control .....11 P, Q Package contents....3 Battery pack Page/find.......17 Charging......9 Replacement and handling ......20 Receiving a call ....12 Redialing a call .....12 Handset ringer tone .....11 Channel .........16 Connection......5 Setup Base unit ......4...
Need help?
Do you have a question about the EXP 8000 Series and is the answer not in the manual?
Questions and answers