Additional Information; General Setup Information; Troubleshooting - Sony SLV-D360P Service Manual

Additional Information

General setup information

1
Press SET UP when the DVD player is in stop
mode, then press V/v to select
(OPTION), then press ENTER.
Press V/v to select the option to change.
2
Press B/b to change the setting.
3
When changing the "RF Output Channel," confirmation messages will
appear. Press ENTER to confirm the messages.
110
General setup information
5 Turn on your TV and set it to the channel you selected in step 1 (3CH or 4CH).
The channel you selected in step 4 appears on the TV screen. If the channels
change when you press CH +/–, you have made the correct setting.
Whenever you use the DVD-VCR, set the TV to the channel selected in step 1.
Attaching the external antenna connector
When using a 300-ohm twin lead cable for a
VHF/UHF antenna, use an antenna connector
(not supplied) to connect the antenna to the
DVD-VCR.
1
Loosen the screws on the antenna connector.
2 Wind the twin leads around the screws on the antenna connector.
3
Retighten the screws.
Attaching a VHF/UHF band mixer
When using both a 75-ohm coaxial cable and
a 300-ohm twin lead cable for a VHF/UHF
antenna, use a VHF/UHF band separator/
mixer (not supplied) to connect the antenna
to the DVD-VCR.
1 Loosen the screws on the mixer.
2
Wind the twin leads around the screws on the mixer.
3
Retighten the screws.
4 Connect the 75-ohm coaxial cable to the mixer.
112
General setup information
SET UP
V/v/B/b
ENTER
OPTION SETUP
:English
Language
Clock Set/Adjust
Channel Setup
Auto Power Off [ Off ]
RF Output Channel [3CH]
V v
ENTER RETURN SET UP
OPTION SETUP
Language :English
Clock Set/Adjust
Channel Setup
[ Off ]
Auto Power Off
RF Output Channel [3CH]
V v B b
RETURN SET UP
300-ohm twin
lead cable
Antenna
connector
(not supplied)
300-ohm twin
lead cable
VHF/UHF
band
separator/
mixer (not
supplied)
75-ohm coaxial
cable
1-27
4
Press SET UP to exit the menu.
Menu choices
The default settings are indicated in bold print.
Menu option Set this option to
Auto Power Off • "Off" to deactivate the Auto Power Off function.
• "1Hr"/"2Hr" to turn the DVD-VCR off automatically if no
signal is received and you do not press any of the buttons
during this time.
RF Output Channel • "3CH" when using channel 3 to receive the VCR signal.
• "4CH" when using channel 4 to receive the VCR signal.
For details, see page 111.
Setting the RF Output channel
When connecting the DVD-VCR to the TV
using only the antenna cable, you must set
the RF Output channel in the "OPTION
SETUP" menu so that the TV can receive the
correct signal from the DVD-VCR.
TV
?/1
CHANNEL +/–
1
Set the RF Output channel to "3CH" or "4CH" (see page 110 to set the channel),
whichever channel is not used in your area. If both are used, set the switch to
either channel.
Press ?/1 to turn on the DVD-VCR.
2
3
Press TV/VIDEO to turn on "VIDEO" in the DVD-VCR's display window.
4 Press CH +/– to display a channel number in the display window.
Select an active channel number in your area.

Troubleshooting

If you have any questions or problems not covered below, please consult your nearest Sony
dealer. (For customers in USA)
General Troubleshooting
Symptom Remedy
The ?/1 switch does not function.
• Connect the AC power cord securely.
The power is turned on but the DVD- • Moisture condensation has occurred. Turn the power off,
VCR does not operate. unplug the AC power cord and leave the DVD-VCR to
dry for over three hours.
The clock has stopped and "–:–" • The clock stops if the DVD-VCR is disconnected from
appears in the display window. the wall outlet. Reset the clock (and timer).
The remote commander does not • Make sure you are pointing the remote commander at the
function. remote sensor on the DVD-VCR.
• Replace all the batteries in the remote commander with
new ones if they are weak.
• Make sure the TV / DVD·VIDEO switch is set correctly.
• Select correctly VIDEO or DVD with the SELECT DVD/
VIDEO button.
The tracking meter does not appear • The recording condition of the tape is very poor and
on the screen. tracking cannot be adjusted.
You cannot control other TVs. • Set your TV's code number. The code number may
change when you replace the batteries of the remote
commander.
?/1
CH +/–
TV/VIDEO
continued
111
General setup information
continued
113
Troubleshooting