Limited Two-Year Warranty; Customer Assistance - Honeywell SuitePRO TB8575 Installation Instructions Manual

TB6575/TB8575 SUITEPRO™ DIGITAL FAN COIL THERMOSTATS
Symptom
Activity Sensing does
not exit when button
pressed
Freeze Protection
does not activate
Auto Fan Reset does
not activate

LIMITED TWO-YEAR WARRANTY

Honeywell warrants this product, excluding battery, to be
free from defects in the workmanship or materials, under
normal use and service, for a period of two (2) years from
the date of purchase by the consumer. If, at any time
during the warranty period, the product is defective or
malfunctions, Honeywell shall repair or replace it (at
Honeywell's option) within a reasonable period of time.
If the product is defective,
(i) return it, with a bill of sale or other dated proof of
purchase, to the retailer from which you purchased it,
or
(ii) package it carefully, along with proof of purchase
(including date of purchase) and a short description of
the malfunction, and mail it, postage prepaid, to the
following address:
Honeywell Return Goods
Dock 4 - MN10-3860
1985 Douglas Dr N
Golden Valley, MN 55422
This warranty does not cover removal or reinstallation
costs. This warranty shall not apply if it is shown by
Honeywell that the defect or malfunction was caused by
damage which occurred while the product was in the
possession of a consumer.
Honeywell's sole responsibility shall be to repair or
replace the product within the terms stated above.
HONEYWELL SHALL NOT BE LIABLE FOR ANY LOSS
OR DAMAGE OF ANY KIND, INCLUDING ANY
By using this Honeywell literature, you agree that Honeywell will have no liability for any damages arising out of your use or modification to, the
literature. You will defend and indemnify Honeywell, its affiliates and subsidiaries, from and against any liability, cost, or damages, including
attorneys' fees, arising out of, or resulting from, any modification to the literature by you.
Automation and Control Solutions
Honeywell International Inc.
1985 Douglas Drive North
Golden Valley, MN 55422
customer.honeywell.com
Table 8. Troubleshooting. (Continued)
Possible Cause
All buttons are locked.
System Type is set to
Cool.
System mode is not Off.
Incorrect IS code.
Calling for Heat/Cool
setpoint couldn't be
satisfied.
Make sure keypad lockout is disabled. Set IS code #18, value = 0.
Freeze protection is not activated when system type is Cool (IS
code #2; value = 1). Change System Type.
Set the System mode button to Off.
Set the Installer Setup code #24 to Enabled (value = 1 or 2).
Only after the setpoint is satisfied, will the auto fan reset timer
activate.
INCIDENTAL OR CONSEQUENTIAL DAMAGES
RESULTING, DIRECTLY OR INDIRECTLY, FROM ANY
BREACH OF ANY WARRANTY, EXPRESS OR
IMPLIED, OR ANY OTHER FAILURE OF THIS
PRODUCT. Some states do not allow the exclusion or
limitation of incidental or consequential damages, so this
limitation may not apply to you.
THIS WARRANTY IS THE ONLY EXPRESS
WARRANTY HONEYWELL MAKES ON THIS
PRODUCT. THE DURATION OF ANY IMPLIED
WARRANTIES, INCLUDING THE WARRANTIES OF
MERCHANTABILITY AND FITNESS FOR A
PARTICULAR PURPOSE, IS HEREBY LIMITED TO
THE TWO YEAR DURATION OF THIS WARRANTY.
Some states do not allow limitations on how long an
implied warranty lasts, so the above limitation may not
apply to you.
This warranty gives you specific legal rights, and you may
have other rights which vary from state to state.
If you have any questions concerning this warranty,
please write Honeywell Customer Relations, 1985
Douglas Dr., Golden Valley, MN 55422 or call 1-800-468-
1502, Monday-Friday, 7:00 a.m. to 5:30 p.m., Central
time.

CUSTOMER ASSISTANCE

If you have any questions about the operation of your
thermostat, please go to customer.honeywell.com
® U.S. Registered Trademark
© 2013 Honeywell International Inc.
62-0278—13 K.K. Rev. 10-13
Printed in United States
Action