nuVita Audiovoice 1098 Instructions

NUVITA AUDIOVOICE 1098
EN

IMPORTANT SAFETY INSTRUCTIONS

WARNING!
STRANGULATION HAZARD - Keep the adapter cord out of baby's reach
• Never place camera or cords within the cot/crib
• The baby unit and cables should be at least 3 ft/1 m away from children
•
Secure the cord to the wall to keep cord away from the baby's reach
•
Never use extension cords with AC adapters. Only use the AC adapters
provided
WARNING
• This baby monitor is not designed to replace responsibility of human supervision
on children.
• This baby monitor must be assembled and installed by an adult.
• This product is designed for indoor use.
• Read these instructions.
• Keep these instructions.
• Heed all warnings.
• Follow all instructions.
• Clean only with dry cloth.
• Do not use this baby monitor near water.
• Do not install this baby monitor near a heat source.
• Do not cover the baby monitor with a towel or blanket.
• Unplug this apparatus during lightning storms or when unused for long periods
of time.
• The small parts of this baby monitor can be swallowed by babies or small
children.
• Keep these parts out of reach of children.
• Do not touch the plug contacts with sharp or metal objects.
Protect the power cord from being walked on or pinched, particularly at plugs,
convenience receptacles, and the point where they exit from the apparatus.
• Only use the power adapters provided. Do not use other charges or power
adapters as this may damage the device and battery pack.
CAUTION!
Risk of explosion if battery is replaced by an incorrect type. Dispose of used
batteries according to the instructions.

PRODUCT AND ACCESSORIES

CONTENTS
• Baby unit x1 • Power adapter for the parent unit x1
• Parent unit x1 (shorter cable one)
• Rechargeable Lithium battery x1 • Screws and extension bolt x2 to mount
• Power adapter for the baby unit x1 baby unit on the wall.
(Longer cable one) • User's guide x1

OVERVIEW OF THE BABY UNIT

06. On/Off Switch
01. Camera lens
07. Power adapter connector
02. Photo sensor (Night Vision on/off)
03. Microphone
08. Power Led
04. Antenna
09. Pairing key (for service center use only)
05. Speaker

OVERVIEW OF THE PARENT UNIT

mode NORMAL mode ZOOM IN
1 Menu Key ( )
Press to enter/exit right arrow to move
menu image to the right
2 Talk Key ( )
press and hold to speak to left arrow to move
your baby image to the left
3 Display (LCD)
4 Vox Mode LED (green Led)
5 Speaker
6
Power LED (Power on = steady green; Power low = flashing red)
7 Microphone
8 Zoom key ( )
press to zoom in 2X, press again
to go back to 1X
9 Volume up ( )
Adjust audio level up arrow to move
louder image to the top
10 Volume down ( )
Adjust audio level down arrow to move
lower image to the bottom
Belt clip
11
12 Stand
13 Battery Cover
14 Audio level LEDs (blue LEDs)
15 Power adapter connector
16 Power On/Off switch ( )
(Press and hold to turn on/off parent units)
SIGNIFICATO DELLE ICONE DEL MENU NELL'UNITÀ GENITORE
Battery level (3 levels plus flashing of battery low)
Signal strength (4 levels)
Talk Mode
Night Vision Mode (Image becomes black/white)
VOX mode (Baby and parent unit are in sleep mode while baby sleeps.
Baby and parent unit will start streaming video and audio when baby cries)
Trigger sensitivity level (3 levels)
Brightness level (5 levels)
Out of range/Lost link alert
Auto mute on/off. Switch auto mute "on", parent unit enters audio mute mode
automatically when baby does not make much noise. Parent unit starts to
stream audio when baby's sound level exceeds preset sensitivity level

GETTING STARTED

PLUG IN BABY UNIT POWER ADAPTER

• Make sure to use provided (6V 800mA) power adapter, the longer cable one.
•Slide the switch to On position to turn on baby unit. Green power LED is turned on.
mode MENU
PLUG IN BABY UNIT POWER ADAPTER
• Make sure to use provided (6V 800mA) power adapter, the shorter cable one.
• Plug in adapter to parent unit to charge parent unit for at least 4 hours before using
the parent unit for the first time.
•
Press and hold power On/Off key for 2 seconds to turn on parent unit.
•
Once the baby and parent units are switched on, the display on the parent unit will
show the video captured by the baby unit.
•
If there is no connection or you are out of range, the video display will go off and
to switch between the Lost Link signal will be shown on the LCD display with beep sounds every 3
menu items
seconds. Move the parent unit closer to the baby unit until the link is re-established.
to switch between
menu items
to switch between
menu items

OPERATION ON RECHARGEABLE BATTERIES

• The parent unit comes with a rechargeable Li-ion polymer rechargeable
battery.
• The battery symbol flashes and power LED flash red when battery is empty.
• If the battery is completely empty, the parent unit automatically switches off
and loses contact with the baby unit.
The rechargeable battery is inside of the parent unit. If you need replacement
of battery when battery has reached end of life, please follow the following
steps:
Slide open battery compartment lid to remove it.
Insert the rechargeable battery with cable alignment
as shown in figure.
Reattach the lid.
•
Charging normally takes 2.5 hours, but it takes longer when the parent unit
is switched on during charging. To keep charging time as short as possible,
switch off the parent unit during charging.
• When the rechargeable battery is fully charged, the parent unit can be used
approximately 10 hours if the parent unit is on VOX mode.