Table of Contents
Advertisement
Downloading/Installing Programs from the Internet
To download and install Software Applications from the Internet onto your Xi3 NUC, take the following steps.
1. Make sure you are connected to the Internet.
2. Go to the appropriate page on the web.
3. Follow the instructions for downloading the application.
4. Download and install the application.
Installing Programs from a USB Thumb drive
To install Software Applications from a USB thumb drive onto your Xi3 NUC, take the following steps.
1. Insert the USB thumb drive into an open USB port on the back of your Xi3 NUC.
2. Within the Operating System, highlight the Software Applications you wish to install onto your Xi3 NUC.
3. Follow the Operating System instructions and install the Software Applications to your Xi3 NUC hard drive.
Installing Programs from a DVD/CD
To install Software Applications from a DVD or CD onto your Xi3 NUC, take the following steps.
1. Connect an external DVD/CD drive to your Xi3 NUC (typically through an available USB port).
2. Insert the DVD or CD into your DVD/CD drive.
3. Within the Operating System, highlight the Software Applications you wish to install onto your Xi3 NUC.
4. Follow the Operating System instructions and install the Software Applications to your Xi3 NUC hard drive.
Copying Existing Files to the Xi3 NUC from an Older PC
If you have files, photos, videos or other forms of data on your existing computer that you would like to move onto your Xi3 NUC, there are
several ways to accomplish this. If you have a lot of files to copy and you have access to a DVD or CD burner, you can copy these files onto
a DVD or CD and then follow the steps outlined above in the Installing Programs from a DVD or CD or Installing Programs from a USB
thumb drive sections above. You will be installing files instead of "programs." There are also numerous software applications that are
free, or for a nominal fee, that can be installed onto your Xi3 NUC and will walk you through the file transfer process step by step.
If you have only a few files to copy, however, you may choose to email the files to yourself as this is often the easiest way to move files
from one computer to another. Simply send an email to yourself from your old computer and attach the files you want to that email.
Then open the email on your Xi3 NUC and save the files onto your new Xi3 NUC.
Once you have successfully booted-up/turned-on your Xi3 NUC and have installed and/or transferred all of the Software Applications and
files/data onto your new machine, you're ready to start using your new Xi3 NUC.
Chapter 2 – Get to Know your NUC
All Xi3 NUCs come pre-built to include the RAM, Intel® SSD, a professionally imaged Operating System and WiFi
(varies by model).
Processor
Intel® Core™ i5-3427 Processor (1.8GHz with turbo capability to achieve 2.8GHz, Dual-Core processor with 3MB
smart cache), supports HyperThreading Technology and Supports Intel® 64 architecture.
The Intel® NUC Board has a soldered-down Intel® Core i5-3427 processor with Integrated Graphics Technology and
integrated memory controller.
System Memory
Dual-Channel DDR3 with two connectors for 1600/1333/1066 MHz memory support (16GB max). Integrated memory
configurations available through Xi3 include 4GB (1x4GB), 8GB (2x4GB), 8GB (1x8GB) and 16GB (2x8GB).
The board has two 204-pin SO-DIMM sockets and support the following memory features:
•
1.5V DDR3 SDRAM SO-DIMMs with gold plated contacts
•
Support for 1.35 V Low Voltage DDR3 (new JEDEC specification)
•
Two independent memory channels with interleaved mode support
•
Unbuffered, single-sided or double-sided SO-DIMMs
•
16GB maximum total system memory (with 4Gb memory technology)
•
Minimum recommended total system memory: 1024MB
•
Non-ECC SO-DIMMs
•
Serial Presence Detect
•
DDR3 1600 MHz and DDR3 1333 MHz SDRAM SO-DIMMs
Advertisement
Table of Contents
