Miele DA424V-6 Installation Instructions Manual
Hide thumbs
Also See for DA424V-6:
- Operating and installation instructions (56 pages) ,
- Operating and installation instructions (64 pages) ,
- Operating instructions manual (448 pages)
Table of Contents
Related Manuals for Miele DA424V-6
Summary of Contents for Miele DA424V-6
-
Page 1: Installation Instructions
Installation Instructions DA424V-6 en - CA Installation, repair and maintenance work should be performed by a Miele authorized service technician in accordance with national and local safety regulations and the provided installation instructions. -
Page 2: Before Installation
Installation Before installation Before installing the appliance, read all of the information contained 4 telescopic extension piece holders in this chapter and also in the "IMPORTANT SAFETY for aligning and securing the telescopic chimney INSTRUCTIONS" section. Installation parts 4 screws M³/₁₆" x ⁵/₁₆" (M4 x 8.5 mm) for securing the telescopic extension piece holders. -
Page 3: Appliance Dimensions
Installation Appliance dimensions a Mounting area for the exhaust ducting and power cable. In recirculation mode, only the power cord is required. b Alternative installation with spacer frame c A power cord is required to connect the hood to the outlet in the ceiling. With extraction mode flexible ducting is also required. -
Page 4: Distance Between Cooktop And Ventilation Hood (S)
Please also observe the information contained in the "IMPORTANT SAFETY INSTRUCTIONS" section. Minimum distance S Cooking appliance Miele range Non-Miele range Electric Cooktops 24" (610 mm) Electric Barbeques and Fryers 26"... -
Page 5: Installation Recommendations
Installation Installation recommendations Structural support – When selecting an installation height, always take the user height into consideration. Users should have ample space to work comfortably on the cooktop and reach the ventilation hood controls with ease. – Please note that the greater the distance from the cooktop, the less effective the hood is at drawing in the cooking vapors. - Page 6 Installation " " For vented mode: – Place a section of the exhaust ducting in the ceiling and feed it down through the cross-sectional area as illustrated. Exhaust ducting of approx. 8" (200 mm) length is required between the ceiling and the dai3435aus hood exhaust socket.
- Page 7 Installation Use a knife to release the four spacers and the two covers from the spacer frame supplied. Drill four holes ³/₈" (10 mm), approx. 4 ¹/₂" (115 mm) deep for the plugs supplied. Use the spacer frame as a drilling ...
- Page 8 Installation Loosen the two telescopic extension The spacer frame can be installed piece holders from the installation between the chimney and the ceiling. frame. This creates a shadow which gives the illusion of a gap between the ceiling and the chimney. This is useful if the ceiling is not level or is uneven.
- Page 9 Installation Mount the spacer frame onto the Hang the hood on the four screws, installation frame. making sure the controls are at the front. If using the spacer frame, place the two covers into the fixing holes.
- Page 10 Installation Place the exhaust ducting onto the exhaust socket. Connect the power cord. See "Electrical connection." Align the installation frame and secure it with the screws. The spacers, which were removed from the spacer frame at the start, can be used to align the hood vertically.
- Page 11 Installation Remove the grease filters from the hood. Push the tower and the telescopic extension piece upwards and bend the retaining tabs outwards again to prevent the tower and telescopic extension piece from slipping down again. Remove the safety screw for the tower on the inside of the frame.
- Page 12 Installation When the canopy is lowered, the safety distance to the cooker may not be exceeded (see "Appliance dimensions"). The height range for the appliance can be extended or limited by moving the limit switch. Press the button. The canopy will be lowered to its fullest extent.
- Page 13 Installation Move the canopy to the required height by pressing the button and stop it by pressing the or button. Hold the chimney securely, bend Screw on the limit switch opposite back the retaining tabs and carefully the guide.
- Page 14 Installation T20 M4x16 Insert the safety screw on the inside. Carefully remove the protective foil from the grease filters. Reinsert the grease filters.
-
Page 15: Exhaust Duct
Exhaust duct – Make sure that all connections are WARNING: Danger of toxic fumes. secure and airtight. Gas cooking appliances release carbon monoxide that can be Remember that any constriction of harmful or fatal if inhaled. the airflow will reduce extraction To reduce the risk of fire and to performance and increase operating properly exhaust air, the exhaust... -
Page 16: Condensate Trap
Exhaust duct Condensate trap In addition to insulating the exhaust duct, we recommend installing a condensate trap to collect and evaporate any condensate which might accumulate. Condensate traps are available for exhaust ducts with a diameter of 5" (125 mm) or 6" (150 mm). ... -
Page 17: Electrical Connection
If there is any question concerning the electrical connection of this appliance to your power supply, please consult a licensed electrician or call Miele’s Technical Service Department. WARNING: THIS APPLIANCE MUST BE GROUNDED... - Page 18 Activating Con@ctivity 2.0 Installation of the Con@ctivity Activating the ventilation hood 2.0 stick The cooktop and hood must be switched off. In order for you to be able to use the Con@ctivity 2.0 function, the cooktop Press the delayed shut-down button must be equipped with a Con@ctivity 515 for approx.
- Page 19 Activating Con@ctivity 2.0 Activating the cooktop Activation failed While the ventilation hood is If a wireless connection cannot be searching for a wireless connection, established despite activation of the start activation on the cooktop. Con@ctivity function on the More information can be found in the ventilation hood and cooktop, the operating instructions for the...
-
Page 20: Service And Warranty
Service and warranty For faults that you cannot resolve on your own, please contact your Miele dealer or Miele Technical Service. The telephone number for the Technical Service Department is listed at the back of these instructions. When contacting Miele, please state the model and serial number of your ventilation hood. -
Page 21: Technical Data
Technical data Fan motor 350 W Height adjustment motor 150 W LED cooktop lighting 4 x 3 W Total connected load 512 W Voltage, frequency 120 V AC, 60 Hz Fuse rating 15 A Weight 107.8 lbs (49 kg) Contains FCC ID: 2ACUWEI8800 IC: 5669C-EI8800 This device complies with Part 15 of the FCC Rules and with Industry Canada... - Page 24 Technical Service. U.S.A. Canada Miele, Inc. Importer Miele Limited National Headquarters 9 Independence Way Headquarters and Miele Centre Princeton, NJ 08540 161 Four Valley Drive Phone: 800-843-7231 Vaughan, ON L4K 4V8 609-419-9898 www.miele.ca 609-419-4298...
- Page 25 DA 424V-6 en-US M.-Nr. 10 118 580 / 00...