Unpacking - Sandstrom SHDFSAT12 Instruction Manual

Thank you
for purchasing your new
Sandstrøm freesat+ Satellite Recorder.
We recommend that you spend some time reading
this instruction manual in order that you fully
understand all the operational features it offers. You
will also find some hints and tips to help you resolve
any issues.
Read all the safety instructions carefully before use
and keep this instruction manual for future reference.
Remove all packaging from the unit.
Retain the packaging. If you dispose of it please do so
according to local regulations.
In addition to this manual the items shown on the right
are included:
SHDFSAT12_IB_V2.indd 3
Power Rec
The Unit
HDMI Cable Mains Adapter
Remote Control Batteries
3

Unpacking

CH+ CH- R
Mains Cable
4 Connection
Place your unit on a firm, level surface close to your TV, a mains electricity socket, and the cables from the satellite dish.
Quick Start Manual 1. Connect the cables from your satellite dish to the sockets on the back of the unit. For full functionality of your freesat+ recorder you will
need to connect two cables from your satellite dish. If you only have one cable, please consult your retailer or installer for advice.
Connecting the two cables
Welcome to your new freesat+ 500GB satellite recorder.
This allows you to watch one TV station and record another. Connect the two separate cables from your satellite dish to each of the
TUNER 1 (LNB IN) and TUNER 2 sockets. For this your Satellite Dish must be fitted with a Low Noise Block (LNB) that has at least two
outputs. Please check with your installer if you are not certain about this.
How to set up and use your
SHDFSAT12
For help with set-up or for more information about
freesat please visit www.freesat.co.uk or call 0845 313 0051.
For specific queries about this box and handy hints and tips
please visit www.knowhow.com/knowledgebank
or call 0844 5611234.
(QSG-SHDFSAT12-130613V3)
These cables only need to be hand tightened, overtightening could result in damage to the unit.
1 Unpack 2 Connect to a Dish 2. Ensure your TV is turned off, then connect the HDMI cable
supplied to the HDMI socket at the back of the unit and an HDMI
socket on your TV. There may be more than one HDMI socket
To receive freesat, you must on your TV. If you are not sure which one to use, check the TV's
Power Rec connect your unit to an appropriate instruction manual. If your TV does not have an HMDI socket, you
CH+ CH- R satellite dish. can connect the unit using a SCART cable (not supplied), but will
The Unit
not be able to view freesat channels in high definition.
For safety reasons and to
Mains Cable provide reliable reception, 3. Connect the mains cable to the mains adapter and then connect
we strongly recommend to the power socket at the back of the unit.
Remote Control that the satellite dish is
HDMI Cable professionally installed. If you
have any questions about the
satellite dish, please consult
Instruction Manual Mains Adapter Batteries your installer. To access On Demand TV you will have to connect an Ethernet cable (not supplied) to your Freesat box.
3 Connection Overview 5
Switch On
TUNER 2 TUNER 1 Remove the battery
LNB in S/PDIF compartment cover from
350mA Max 14/19V the back of the remote
ETHERNET USB HDMI TV VCR DC 12V 2.5A
OR control by lifting it up while
pushing the catch. Insert the
two AAA sized batteries as
shown on the inside of the
compartment. Replace the
compartment cover.
Satellite Dish TV Mains Power
SHDFSAT12_Quick Start Guide.indd 1
Quick Start Guide
Turn on your TV set and choose the HDMI input
(see your TV's instruction manual).
Switch on the mains socket the unit
is connected to. After a few seconds,
the first freesat installation screen
will show on the TV screen.
If you do not see this screen on the
TV screen, see the Hints and Tips
section in the main instruction manual.
13/06/2013 12:13
13/06/2013 12:19