Tecsun PL-365 Operation Manual
  1. Manuals
  2. Brands
  3. Tecsun Manuals
  4. Receiver
  5. PL-365
  6. Operation manual

Tecsun PL-365 Operation Manual

Fm stereo / mw / sw-ssb dsp receiver
Hide thumbs Also See for PL-365:
Table of Contents

Advertisement

Quick Links

See also: Operating Manual
Enlarged version
TECSUN
TECSUN
PL-365
FM stereo / MW / SW-SSB DSP RECEIVER
OPERATION MANUAL
TECSUN
SLEEP
PL-365
TECSUN ELECTRONIC IND. LTD.
FM STEREO / MW / SW-SSB DSP RECEIVER
Address: Rm 11, 13/F, Block A, Hoi Luen Ind. Ctr.,
55 Hoi Yuen Road, Kwun Tong, Kowloon, Hong Kong.
E-mail: tecsun@on-nets.com
TECSUN ELECTRONIC IND. LTD.
Website: www.tecsun.com.cn
20150120

Advertisement

Table of Contents
loading

Related Manuals for Tecsun PL-365

Summary of Contents for Tecsun PL-365

  • Page 1 FM stereo / MW / SW-SSB DSP RECEIVER OPERATION MANUAL TECSUN SLEEP PL-365 TECSUN ELECTRONIC IND. LTD. FM STEREO / MW / SW-SSB DSP RECEIVER Address: Rm 11, 13/F, Block A, Hoi Luen Ind. Ctr., 55 Hoi Yuen Road, Kwun Tong, Kowloon, Hong Kong. E-mail: tecsun@on-nets.com TECSUN ELECTRONIC IND.
  • Page 2 SPECIFICATIONS PL-365 Functional Block Diagram PL-365 is equipped with DSP si4735 microchips (from Silicon 1. Frequency range Labs in the USA) for digital demodulation of analog AM/FM 87~108 MHz broadcasting signals, which greatly enhances the radio's Japan 76~108 MHz sensitivity, selectivity, S/N ratio and anti-interference.

  • Page 3: Table Of Contents

    TABLE OF CONTENTS CONTROL LOCATIONS........... 2 QUESTIONS ANSWERS SOLUTIONS LCD DISPLAY..............4 When the alarm -Did not set the -Preset your alarm TURN ON / OFF THE RADIO ..........5 (radio) goes off, proper radio station station properly TUNE INTO STATIONS............6 there is only for the alarm.

  • Page 4: Control Locations

    Poor AM -USA uses 10kHz -Turn off the radio reception in USA. AM tuning steps, press the [9/10kHz] the device may still button to select PL-365 be set to 9kHz. accurate tuning step. FM STEREO / MW / SW-SSB DSP RECEIVER...
  • Page 5 IMPORTANT MATTERS FOR USING BATTERIES 1. When the device is not powered by batteries or the Power on/off adaptor for a long time, the clock setting is lost, but the stored radio stations are saved. Multifunctional tuning knob 2. When battery power is low, the " "...

  • Page 6: Lcd Display

    LCD DISPLAY USING THE INTELLIGENT CHARGING FUNCTION In power off mode, install 3 x UM3 (AA size) rechargeable 1 2 3 4 (Ni-MH) batteries. Press & hold the [ ] button until “ " and the "Ni-MH Battery" symbol appear on the SLEEP display.

  • Page 7: Turn On / Off The Radio

    Use the external wire antenna to clip onto the telescopic PL-365. To remove the battery compartment cover, apply antenna of the PL-365. Then position the opposite end thumb pressure and slide it towards the bottom of the outside the window for better FM and SW reception.

  • Page 8: Tune Into Stations

    TUNE INTO STATIONS Short press [POWER] button to turn on your radio, then Turn ON/OFF charging function & exchange battery select your desired band by short pressing the [FM], [MW], consumption display SW [ ] or [ ] button. In case of receiving FM/SW Press &...

  • Page 9: Manual Tuning

    SYSTEM SETTING MW station: It is recommended to perform the ETM Frequency range setting for FM function during day time as well as night time, because Press & hold the [FM] button until 76-108MHz, 87-108MHz there usually are more stations that start broadcasting at or 87.5-108MHz appears on the display.

  • Page 10: Auto Scan Stations

    TURN OFF THE ALARM When the radio is turned on by the alarm function with radio, Method 4: AUTO BROWSE MEMORY you can short press [POWER] button to continue listening 1. Turn on the radio to enter memory radio afterwards. mode.

  • Page 11: Working With Memories

    SETTING THE CLOCK WORKING WITH MEMORIES The PL-365 has 550 station memories: FM (100), MW (100), 1. Long press the [TIME] button until you see the hour SSB (100) and SW (250). flashing. Rotate the [TUNING] knob to set the correct hour, then short press the [TIME] button and notice the minutes are flashing.

  • Page 12: Semi-Auto Station Storage

    Method 2: SEMI AUTO-DELETE MEMORY Method 2: MANUALLY STORING STATION Press the [VF/VM] button to enter the memory mode, 1. Tune to your desired station, press the [MEM.] button then press & hold the [VF/VM] button to activate the once and notice the PRESET number flashing in the memory auto-browse function.

Table of Contents