Table of Contents
Advertisement
Registration, Service & Assembly
Thank you for purchasing the CG-9506 Bicep/Tricep. This machine is part of the
TuffStuff line of quality strength training equipment. To maximize your use of the equipment, please study the Owner's Manual thoroughly.
Registration
To avoid unnecessary delays on warranty parts and to insure that a
permanent record of your purchase is on file with our company, be
sure to register online at http://www.tuffstuffitness.com or mail to
address shown below within 10 days of purchase.
Obtaining Service
Please use this Owner's Manual as your guide to all parts included in
your shipment. When ordering parts, you must specify the part number
and description from this owner's manual. Use only genuine TuffStuff
replacement parts when servicing the equipment. Failure to do
so will void warranty and could result in serious injury or death.
For information about product operation or service:
Phone:
909-629-1600 Toll Free 888-884-8275
Fax:
909-629-4967
E-mail:
service@tuffstuff.net or service1@tuffstuff.net
Hours:
M–F 8:00 – 4:30 PST
Or write to:
TuffStuff Fitness International Inc.
Customer Service
13971 Norton Avenue, Chino, CA 91710
Retain this Owner's Manual for future reference when ordering
service or parts. To assist you better, please be prepared to
provide the following information:
1. Model Number
3. Serial Number
Required Tools
The basic tools that you will need to assemble the CG-9506 but are not
limited to:
• 9/16" , 3/4", 1/2" combination wrenches
• Adjustable wrench
• Ratchet wrench with 9/16" , 3/4", 1/2" sockets
• External retaining ring pliers
• Rubber mallet, measuring tape & utility knife
• Super Lube® spray lubricant and grease
• Windex or household glass cleaner
Assembly Requirements
Follow these installation requirements when assembling the
CG-9506. Use the overhead view on the Content Page to layout your floor
plan before assembling.
Set up the CG-9506 on a clean, solid, flat surface. A smooth, flat surface
under the machine helps keep it level.
10
www.tuffstuffitness.com
2. Place of Purchase
4. Part # and Description
Allow ample space around the machine for safe unrestricted use and
easier access.
Insert all bolts in the same direction. For aesthetic appearance, insert all
bolts in the same direction unless specified (in text or illustration) to do
otherwise.
Leave room for adjustments. Do not fully tighten fasteners until
instructed in the assembly steps to do so (to prevent any difficulty with
alignment of parts during the assembly process). When not instructed,
tighten fasteners such as bolts, nuts and screws so the unit is stable, but
leave room for adjustments.
Assembly Tips
Read all "Notes" on each page before beginning each step.
While you may be able to assemble the CG-9506 using the illustrations
only, IMPORTANT safety notes and other tips are included in the text.
Some pieces may have extra holes that you will not use. Use only those
holes indicated in the instructions and illustration.
NOTE:
With so many assembled parts, proper alignment and
adjustment is critical. While tightening the nuts and bolts,
be sure to leave room for final adjustments.
CAUTION: Obtain assistance from TFI if you have difficulty
assembling the CG-9506. Please do not attempt to
complete the assembly as this could result in equipment
failure and serious injuries to the users.
Symbols & Description
Loosely Tighten
Loosely Tighten
Loosely tighten all hardware in this step. DO NOT Fully
70%
Tighten. Some component(s) may need pre-assembly
and or alignment during the assembly process.
Fully Tighten
Fully Tighten
Wrench tighten all hardware in this step.
100%
CG-9506 Bicep/Tricep
Advertisement
Table of Contents
