Page 1
1. To disclose and post all Rules & Regulations, Danger, Warning and Caution Bicep/Tricep labels affixed on the machine to their customers/users. 2. Equipment to be installed by TFI Authorized Dealer or a service company approved by TFI. 3. Provide trained personnel, supervision and correct usage of the equipment.
Should additional information be required, or should situations arise that are not covered by this owner’s manual, the matter should be directed to Customer Service at TuffStuff Fitness International Inc. in Chino, California. www.tuffstuffitness.com CG-9506 Bicep/Tricep...
Overhead Specifications L 38” X W 33” X H 80” MAX-LOAD WEIGHT LIMIT -200 lbs CG-9506 Bicep/Tricep www.tuffstuffitness.com...
Page 4
Carefully read ALL Danger, Warning & Caution labels posted on the machine www.tuffstuffitness.com CG-9506 Bicep/Tricep...
Page 5
Carefully read ALL Danger, Warning & Caution labels posted on the machine CG-9506 Bicep/Tricep www.tuffstuffitness.com...
Page 6
Carefully read ALL Danger, Warning & Caution labels posted on the machine www.tuffstuffitness.com CG-9506 Bicep/Tricep...
Page 7
You should have received it along with this Owner’s Manual� If you did not receive this Facility Sign with your order, you can obtain one at no cost to you from TuffStuff Fitness by contacting our service department at: 1 (888) 884-8275 service@tuffstuff�net service1@tuffstuff�net CG-9506 Bicep/Tricep www.tuffstuffitness.com...
Anchoring Unit Holes on frame are provided for anchoring the unit to the floor� See anchoring hole location below� www.tuffstuffitness.com CG-9506 Bicep/Tricep...
14. Maintain a service contract with a TFI Authorized Dealer or a Do not use accessories or accessory attachments that are not Professional Service Company approved by TFI. Keep a service recommended by TFI.
4. Part # and Description failure and serious injuries to the users. Required Tools Symbols & Description The basic tools that you will need to assemble the CG-9506 but are not limited to: • 9/16” , 3/4”, 1/2” combination wrenches • Adjustable wrench •...
Perform regular maintenance (see Inspection Label). Pay special attention to areas most susceptible to wear and tear, including but not limited to cables, pulleys and rubber grip. TFI recommends you maintain a service contract with a TFI Authorized Dealer or a Professional Service Company approved by TFI.
A BREAK ON THE CABLE CABLE END SLIPPING OUT IMPORTANT NOTE: DAMAGED OR WORN CABLE (AS SHOWN ABOVE) MAY DAMAGE THE PULLEY(S)� YOU MUST INSPECT THE PULLEYS AT THIS TIME FOR WEAR AND TEAR� REPLACE IF NEEDED� www.tuffstuffitness.com CG-9506 Bicep/Tricep...
1. It is strongly recommended that 2 people participate in the assembly of this unit. 2. Be sure to hold the weight stack frame perpendicular to floor before tightening the screws. Fully Tighten 100% Fully Tighten Wrench tighten all hardware in this step. CG-9506 Bicep/Tricep www.tuffstuffitness.com...
Step 3 Note: 1. Be sure to position bracket #4 given degrees. Otherwise the plastic shroud lid will not assemble. 36.00° Fully Tighten 100% Fully Tighten Wrench tighten all hardware in this step. www.tuffstuffitness.com CG-9506 Bicep/Tricep...
8� Open the lube package provided and apply a thin film of lubricant around the first 3 inches of the guide rods above the top plate� 9� After the cables are installed, do a set of reps to spread the lubricant thoroughly� CG-9506 Bicep/Tricep www.tuffstuffitness.com...
Step 5 Assembly List Item # Description Qty. WEIGHT SHIELD FRONT WEIGHT SHIELD REAR FLAT HEAD SOCKET CAP SCREW Z/P M6-1.0 X 50 PLASTIC SHROUD LID Fully Tighten 100% Fully Tighten Wrench tighten all hardware in this step. www.tuffstuffitness.com CG-9506 Bicep/Tricep...
BNH3393 BNH3135 RUBBER CORR MAT ON LOW ROW BAR REST BNH3686 LABEL‐TFI 4 HIGH X 4.23 WIDE BLUE AND CHROME BNH3699 RUBBER DONUT 3/4 X 2 1/2 LABEL‐TFI SERIAL NO. 2.5 X 1.5 BNH0068 BNH3147 SHROUD LID RUBBER MAT LARGE BNH3394 PRE ASSEMBLED COMPONENTS Item No. Description Rev. Part No. Qty. Item No. Description Rev. Part No. Qty. ADJ PULLEY BRACKET (3 1/2 PULLEY) WEIGHT SHIELD FRONT UP8800X1 UP8468X1 BASE FRAME WEIGHT STACK FRAME UP8801X1 UP8804X1 FRONT UPRIGHT UP8803X1 PLASTIC SHROUD LID BNH3393X1 CG-9506 Bicep/Tricep www.tuffstuffitness.com...
Pre-Assembled Components *10 UP8804X1 *5 UP8803X1 Note: 1. Be sure to position brackets (#4) given degrees. Otherwise the plastic shroud lid will not assemble. GUIDE WIRE 36.00° 65.00° 23 29 www.tuffstuffitness.com CG-9506 Bicep/Tricep...