Panasonic TH-42PH11RK Operating Instructions Manual page 39

Item
INPUT lock
Button lock
Remocon User level
Advanced PIP
Off-timer function
Initial Power Mode
ID select
Remote ID
Serial ID
Display size
Downloaded From TV-Manual.com Manuals
Off PC INPUT1
Locks the input switch operation.
Notes:
• Only the adjusted signal is displayed (see page 14).
• Signal can be displayed when the Terminal board is installed.
• Input switch can be used when this is set to "Off".
• In two screen display mode, if anything other than "Off" is set, the value will be fi xed as the value input
in the single screen display mode.
• When a dual input terminal board is attached, A or B is displayed depending on the selected input signal.
(Ex. INPUT1A, INPUT1B)
Off MENU&ENTER
Off: All the buttons on main unit can be used.
MENU&ENTER:
Locks and buttons on main unit.
MENU ENTER/
On: Locks all the button on main unit.
Sets Button lock with the unit buttons in the following procedure.
Off: Press four times Press
MENU&ENTER: Press
ENTER/
On: Press four times Press
Off User1 User2
Off: You can use all of the buttons on the remote control.
User1: You can only use
User2: You can only use
User3:Locks all the buttons on remote control.
Off: Sets normal two screen display mode (see page 18).
On: Sets Advanced PIP mode (see page 19).
Notes:
• When "INPUT lock" is "On", you cannot use all the two screen display functions.
• , buttons are unavailable during Advanced PIP mode operation.
Enable: Enables the "Off-timer function".
Disable: Disables the "Off-timer function".
Note: When "Disable" is set, the Off-timer is cancelled.
Normal Standby
Sets the power mode of the unit for when the power recovers from failure or after plugging off and in again.
Normal: Power returns in as the same state as before the power interruption.
Standby: Power returns in standby mode. (Power Indicator : red/orange)
On: Power returns in power On. (Power Indicator : green)
Note: When using multiple displays, "Standby" is preferred to be set in order to reduce a power load.
Sets panel ID number when panel is used in "Remote ID" or "Serial ID".
Set value range: 0 - 100
(Standard value: 0)
The setting of this menu is valid only when using ID remote control.
Off: Disables ID remote control functions. You can use normal remote control operations.
On: Enable ID remote control functions.
Sets the panel ID Control.
Off: Disables external control by the ID.
On: Enables the external control by the ID.
Adjusts the image display size on screen.
Off: Sets the normal image display size on screen.
On: Sets the image display size approximately 95 % of the normal image display.
Off
Notes:
• This setting is valid only when the input signals are as follows;
NTSC, PAL, SECAM, M.NTSC, PAL60, PAL-M, PAL-N (BNC Dual Video Terminal Board (TY-FB9BD)) 525i,
525p, 625i, 625p, 750/60p, 750/50p, 1125/60i, 1125/50i, 1125/24sF, 1125/25p, 1125/24p, 1125/30p,
1125/60p, 1125/50p, 1250/50i (Component Video, RGB, DVI, SDI, HDMI)
• This setting is invalid when two screen display, digital zoom or Multi display is selected.
• When "Display size" is set to "On", "H-Pos" and "V-Pos" in "Pos. /Size" can be adjusted.
• Refer to each board's operating instruction for DVI, SDI, HDMI's corresponding signals.
Adjustments
INPUT2 INPUT3
On
four times Press
INPUT
four times Press four times Press
four times Press
ENTER/
User3
, , , , , buttons on the remote control.
button on the remote control.
On
On
Options Adjustments
four times Press
ENTER/
four times Press
INPUT
four times Press
ENTER/
ENTER/
39