Search Mode - Realistic PRO-2001 Owner's Manual

SEARCH MODE
You can locate the frequency for any unknown station in the VHFI
U H F b a n d s b y u s i n g t h e S e a r c h F u n c t i o n o f y o u r P R O - 2 0 0 1 .
1 . P r e s s S C A N N E R k e y t o s e l e c t a c h a n n e l . ( M o m e n t a r i l y p r e s s t h e
Scanning Switch to MANUAL to advance to a desired channel as
i n d i c a t e d b y t h e C h a n n e l L E D . )
2 . S e t S O U E L C H c o n t r o l t o p o i n t w h e r e a n n o y i n g b a c k g r o u n d n o i s e
just stops.
3 . P r e s s P R O G R A M k e y . ( T h e P r o g r a m L E D w i l l c o m e o n . )
4. Press LO key; then press the numbers for the lower frequency
l i m i t y o u d e s i r e .
5. Press UP key; then press the numbers for the upper frequency
l i m i t y o u d e s i r e .
NOTE: You can set upper and lower Search limits in different bands
i f y o u l i k e . F o r e x a m p l e , y o u c a n s e t t h e l o w e r l i m i t t o
4 0 M H z ( i n V H F L o b a n d ) a n d u p p e r l i m i t t o 4 7 0 M H z ( i n t h e
UHF band). In such a case, those frequencies outside of the
specif ied tuning range will just be skipped.
6. Then, press FS (Fast Search) or SS (Slow Search) key to start
Search. You can change searching speed any time by pressing
either the FS or SS key.
7. When a signal comes in on a frequency between the upper and
lower frequencies you have set, Search stops and the frequency
w i l l b e h e l d u n t i l i t s s i g n a l e n d s . ( l f D E L A Y i s " o n " , f r e q u e n c y
will be held for two seconds after signal ends.)
8. To continue monitoring a frequency you have "discovered", press
MONITOR. This halts the search, stores the frequency in the
in the Monitor Memory, and lets you "listen in" for a while.
9. To enter this frequency into the channel you selected in Step'1,
press ENTer. (You may skip this step if you just wish to monitor
t e m p o r a r i l y . )
10. To resume search where you left off, press FS or SS. To start
search over at lower frequency limit, press UP and LO keys and
then FS or SS.
NOTE:You can return to a channel stored in the Monitor Memory by
p r e s s i n g C L e a r a n d t h e n M O N I T O R .
1 1. When another active f requency is encountered in the search, the
Scanner will hold on this frequency as described in Step 7. lf you
want to stay tuned to this frequency, press MONITOR. The new
frequency will now replace the contents of the Monitor Memory.
1 2 . T o e n t e r t h i s n e w f r e q u e n c y i n t o a c h a n n e l o t h e r t h a n t h e o n e
selected in Step 1, press SCANNER key and use MANUAL
selector to advance to desired channel. Press PROGRAM to return
to programming mode. Press MONITOR to recall the frequency
stored there. Now press ENTer key to put that frequency into the
c h a n n e l m e m o r y .
Continue the process until you've identified the frequencies that
interest you in that search range. To change the upper and lower
limits, just enter ne\t/ ones as described in Steps 4 and 5. The last-
entered search limits are retained in memory, even when the set is
u n p l u g g e d .
N O T E : T o h a l t a s e a r c h a t a n y t i m e , p r e s s M O N I T O R k e y . T h i s w i l l
also place displayed frequency into Monitor Memory.
- 9 -