Advertisement
Install instructions for CI round ush mount models, Page 2
Flange Installation:
1.
Using the supplied cutout template,
carefully mark the area to be cut out. Using
a drywall knife or saw, cut a hole in the
drywall and prepare the speaker wires for
connection to the speaker terminals.
4.
Carefully place the speaker in the ange.
While exerting upward pressure, rotate the
speaker until it ts snugly and the speaker
surface is even with or slightly recessed
into the surface of the ange. Twist the
speaker counter-clockwise (left) to secure
it in place. This will engage the QM SAFETY-LOC™
clamps on the back of the ange. Finish by
tightening the four clamp screws on the
speaker.
CAUTION: Do not over-tighten.
QM SAFETY-LOC™ Clamp
Wiring options for the CI-6.2s
Stereo
FIG. 1 – 8 ohms: Use this
con guration to drive one channel
(left or right ) of a stereo pair. Set
jumper plugs in the stereo position.
Connect the right or left signal wire to
the right set of terminals on the rear of
the speaker.
F
G I
1 .
Jumper Plugs
stereo position
Right Channel
8005 W. 110th St. | Suite 208 | Overland Park, KS 66210 | 855.663.5600 | www.phasetech.com | www.mseaudio.com
2.
Remove the grille from the mounting
ange by pressing it from behind. Insert the
mounting ange into the hole. Loosen the
ange clamping screws one turn (counter
clockwise) to release the clamp. Next,
tighten all four ange clamp screws evenly
to secure the ange to the wall. It is best to
tighten each screw with the same amount of
force (torque).
CAUTION: Do not over-tighten.
NOTE: Special instructions for non-QM
Flanges
If you are installing a CI round speaker with
the QM clamps in a CI-FGR (non-QM ange)
remove the QM clamp feet by unscrewing
them from the speaker ba e. Insert the
speaker ba e into the ange and reuse the
screws from the clamp feet to attach the
speaker to the ange.
Stereo Point Source
–
FIG.2
8 ohms:
Use this configuration to combine left
and right channels for full fidelity sound
from a single loud-speaker stereo source.
Set jumper plugs in the stereo position.
Connect right and left signal wires to the
spring-loaded terminals on the rear of
the speaker.
F
G I
2 .
Jumper Plugs
stereo position
Left Channel
Right Channel
Speaker Installation:
3.
spring-loaded input terminals on the rear of
the speaker, making sure no loose strands
are exposed. If connecting the CI-6.2s VIII QM,
see wiring options below.
+
5.
listen to the tweeter's balance with the level
control in each of its three positions to nd
your favorite.
6.
into the gap between the ange and the
ba e. Enjoy your new Phase Technology
speakers!
Mono/S tereo
FIG.3 – 4 ohms: Use
this configuration to drive one channel
(left or right ) of a stereo pair with a 4
ohm speaker load. Set jumper plugs in
the mono position. Connect the right or
left signal wire to the left set of posts
on the rear of the speaker. Acoustic
output of the speaker is increased by
3 dB in the configuration.
F
G I
3 .
Jumper Plugs
mono position (Bi-pole/di-pole)
Left Channel
Connect the speaker wires to the
_
Red/positive
Black/negative
Using some familiar source material,
Carefully replace the grille by pressing it
Grille
Bi-pole/Di -pole
–
FIG.4
4 ohms: Use this
configuration for home theater surround
applications. For bi-pole mode, connect
as in the Mono/ Stereo instructions
one speaker to each surround channel.
For di-pole mode, connect speaker
inputs the same as Mono/ Stereo
instructions
, but reverse the + and –
(FIG.3)
connections of the marked tweeter wires
to put one of the tweeters out of phase.
FIG.4
:
(FIG.3)
Advertisement
