Broan EI5936SS Instructions Manual
Hide thumbs Also See for EI5936SS:

Advertisement

Chimney Island

Range Hood

READ AND SAVE THESE INSTRUCTIONS
WARNING
TO REDUCE THE RISK OF FIRE, ELECTRIC SHOCK, OR INJURY
TO PERSON(S) OBSERVE THE FOLLOWING:
1. Use this unit only in the manner intended by the manufacturer. If
you have questions, contact the manufacturer at the address or
telephone number listed in the warranty.
2. Before servicing or cleaning unit, switch power off at service panel
and lock service disconnecting means to prevent power from being
switch on accidentally. When the service disconnecting means
cannot be locked, securely fasten a prominent warning device,
such as a tag, to the service panel.
3. Installation work and electrical wiring must be done by qualified
personnel in accordance with all applicable codes and standards,
including fire-rated construction codes and standards.
4. Sufficient air is needed for proper combustion and exhausting
of gases through the flue (chimney) of fuel burning equipment to
prevent back drafting. Follow the heating equipment manufacturer's
guideline and safety standards such as those published by the
National Fire Protection Association (NFPA), and the American
Society for Heating, Refrigeration and Air Conditioning Engineers
(ASHRAE), and the local code authorities.
5. This product may have sharp edges. Be careful to avoid cuts and
abrasions during installation and cleaning.
6. When cutting or drilling into wall or ceiling, do not damage electrical
wiring and other hidden utilities.
7. Ducted fans must always be vented to the outdoors.
8. Use only metal ductwork.
9. Do not use this unit with any other solid-state speed control device.
10. This unit must be grounded.
TO REDUCE THE RISK OF A RANGE TOP GREASE FIRE:
a) Never leave surface units unattended at high settings. Boilovers
cause smoking and greasy spillovers that may ignite. Heat oils
slowly on low or medium settings.
b) Always turn hood ON when cooking at high heat or when flambéing
food (i.e. Crêpes Suzette, Cherries Jubilee, Peppercorn Beef
Flambé).
c) Clean ventilating fans frequently. Grease should not be allowed to
accumulate on fan or filters.
d) Use proper pan size. Always use cookware appropriate for the size
of the surface element.
TO REDUCE THE RISK OF INJURY TO PERSON(S) IN THE EVENT
OF A RANGE TOP GREASE FIRE, OBSERVE THE FOLLOWING*:
1. SMOTHER FLAMES with a close-fitting lid, cookie sheet, or metal
tray, then turn off the burner. BE CAREFUL TO PREVENT BURNS.
IF THE FLAMES DO NOT GO OUT IMMEDIATELY, EVACUATE
AND CALL THE FIRE DEPARTMENT.
FOR DOMESTIC COOKING ONLY
WARNING
2. NEVER PICK UP A FLAMING PAN – You may be burned.
3. DO NOT USE WATER, including wet dishcloths or towels – a violent
steam explosion will result.
4. Use an extinguisher ONLY if:
A. You know you have a Class ABC extinguisher, and you
know how to operate it.
B. The fire is small and contained in the area where it started.
C. The fire department is being called.
D. You can fight the fire with your back to an exit.
* Based on "Kitchen Fire Safety Tips" published by NFPA
CAUTION
1. For indoor use only.
2. For general ventilating use only. Do not use to exhaust hazardous
or explosive materials and vapors.
3. To avoid motor bearing damage and noisy and/or unbalanced
impeller, keep drywall spray, construction dust, etc. off power unit.
4. Your hood motor has a thermal overload which will automatically
shut off the motor if it becomes overheated. The motor will restart
when it will cool down. If the motor continues to shut off and
restart, have the hood serviced.
5. The bottom of the hood MUST NOT BE LESS than 24" and
recommended at a maximum of 36" above cooktop for best
capture of cooking impurities.
6. Two installers are recommended because of the size of this
hood.
7. To reduce risk of fire and to properly exhaust air, be sure to duct
air outside. Do not exhaust air into spaces within walls or ceilings
or into attics, crawl spaces, or garages.
8. Be careful when installing the decorative flue and hood, they may
have sharp edges.
9. This hood is not intended to be used as a shelf.
10. Please read specification label on product for further information
and requirements.
o
Installer: Leave this manual
with the homeowner.
Homeowner: Operation and Maintenance
instructions on pages 8 & 9.
MODEL EI5936SS
Page 1

Advertisement

Table of Contents
loading

Summary of Contents for Broan EI5936SS

  • Page 1: Range Hood

    MODEL EI5936SS Page 1 Chimney Island Range Hood READ AND SAVE THESE INSTRUCTIONS FOR DOMESTIC COOKING ONLY WARNING WARNING TO REDUCE THE RISK OF FIRE, ELECTRIC SHOCK, OR INJURY 2. NEVER PICK UP A FLAMING PAN – You may be burned. TO PERSON(S) OBSERVE THE FOLLOWING: 3. DO NOT USE WATER, including wet dishcloths or towels – a violent 1. Use this unit only in the manner intended by the manufacturer. If steam explosion will result.
  • Page 2: Plan The Installation

    MODEL EI5936SS Page 2 PLAN THE INSTALLATION INSTALL THE CEILING SUPPORT ROOF CAP 8” MINIMUM 6” ROUND DUCT 8½” FRONT ON CENTER DECORATIVE HOOD 6” ROUND HOOD FLUES EAVE CENTERLINE ELBOWS CENTERLINE VENT DUCT DUCT CENTER LINE HOOD CENTERLINE (1” to rear of hood centerline) OFFSET 1”...
  • Page 3: Prepare The Hood

    MODEL EI5936SS Page 3 PREPARE THE HOOD Unpack hood and check contents. You should receive: 1 - Hood Assembly 3 MOUNTING 1 - Glass Canopy SCREWS 1 - Decorative Flue Assembly 3 WIRE NUTS (4mm x 12mm Cross Recessed (consisting of 2-upper and 2-lower flue sections) Pan Head) 1 - Hood Frame Assembly (consisting of upper and lower sections) 2 - Upper Flue Trim Strips 2 - Lower Flue Trim Strips 1 - Aluminum Grease Filter (installed on hood) BULB SUCTION 12 MOUNTING SCREWS...
  • Page 4 MODEL EI5936SS Page 4 INSTALL THE HOOD (Ducted hoods only - Steps 1 & 2) NON-DUCTED HOOD INSTALLATION - SKIP TO STEP 3. LENGTH “L” 1. Determine length “L” of frame assembly based upon desired installation height. (See chart below.) To adjust frame assembly height, remove (8) screws, slide upper frame assembly to required height, replace screws and tighten securely.
  • Page 5 MODEL EI5936SS Page 5 INSTALL THE HOOD (Non-Ducted Hoods Only - Steps 3 thru 8) NON-DUCT KIT MODEL RKE59 CONTENTS 4 MOUNTING SCREWS (3mm x 10mm CEILING Cross Recessed MATERIAL Pan Head) IS INSTALLED. CEILING NON-DUCT PLENUM FRAMING ASSEMBLY 4 MOUNTING...
  • Page 6: Install The Hood

    MODEL EI5936SS Page 6 10. Remove the protective plastic film covering the decorative flue and the hood at this time. 11. Remove the grease filter by pulling down the metal latch tab and tilting filter downward. 8. Attach foam seals to plenum and frame, around the plenum 12. Carefully place glass canopy on top of the hood. Align nuts openings. on glass canopy with holes inside the hood. Attach canopy with (4) .188” x .250” long flat head screws. Tighten screws INSTALL THE HOOD securely but DO NOT OVERTIGHTEN. (All Hoods - Steps 9 thru 25) ELECTRONICS MOUNTING BRACKET 13. Align the keyhole slots on the bottom of the frame assembly with the (4) mounting screws on the top of the hood (partially tightened). Slide the hood so the screw heads are seated entirely on mounting screws and that hood is level. Then tighten screws completely.
  • Page 7 MODEL EI5936SS Page 7 F R O N T NON-DUCT HOOD ONLY 17. Attach filter tray to bottom of hood using (4) .188” x .375” mounting screws. NON-DUCT HOOD ONLY 18. Snap in 2-non-duct filters into filter trays by engaging filter tab on side, rotating upward, and pressing firmly on (2) filter clips. 19. Reinstall grease filter by aligning rear filter tab with slots in the hood. pull down the metal latch tab, push filter into position and release. Make sure filter is securely engaged...
  • Page 8: Operation

    MODEL EI5936SS Page 8 OPERATION Always turn the hood ON before cooking in order to establish an air flow in the kitchen. After turning off the range, let the hood run for a few minutes to clear the air. Operate the hood as follows: DELAY OFF LIGHT FAN SPEED LED INDICATORS Turns the fan OFF FAN (1-Pushbutton Switch, 3-Fan Speeds) Turns the fan ON to the last selected speed, and activates a blue LED indicating the fan speed setting. Pressing the FAN button a second time will index the fan speed and LED indicator to the next highest setting.
  • Page 9: Cleaning And Maintenance

    Make the connection to the Make-Up Air Damper with low voltage wiring, as shown. See Make-Up Air Damper instructions for additional information. REMOTE CONTROL HALOGEN PUSH IN BULB The hood is compatible with Broan Radio Frequency (RF) Remote Control Model BCR1 (optional). Purchase separately. To link the BCR1 remote control with the hood, press and hold the LIGHT ROTATE button for 3-seconds. CLOCKWISE The blue LED indicators will turn on and off in succession to indicate the hood is in RF linking mode. When in the linking mode, press any key on...
  • Page 10: Service Parts

    This warranty gives you specific legal rights, and you may also have other rights, which vary from state to state. This warranty supersedes all prior warranties. To qualify for warranty service, you must (a) notify Broan-NuTone at the address or telephone number below, (b) give the model number and part identification and (c) describe the nature of any defect in the product or part. At...

Table of Contents