Metrologic MS6720 Installation And User Manual

Metrologic MS6720 Installation And User Manual

Hand-held laser scanner
Hide thumbs Also See for MS6720:

Advertisement

MS6720 Hand-Held Laser Scanner
Installation and User's Guide
MLPN 2368
Printed in USA
October 1998

Advertisement

Table of Contents
loading
Need help?

Need help?

Do you have a question about the MS6720 and is the answer not in the manual?

Questions and answers

Summary of Contents for Metrologic MS6720

  • Page 1 MS6720 Hand-Held Laser Scanner Installation and User’s Guide MLPN 2368 Printed in USA October 1998...
  • Page 2: Table Of Contents

    The MS6720 Stand ........
  • Page 3 Appendix A Design Specifications 28, 29 Appendix B Default Settings 30 - 33 Appendix C Pin Assignments 34 - 36 Appendix D Warranty and Disclaimer 37, 38 Appendix E Notices 39, 40 Appendix F Patents 41 Index 42 - 44...
  • Page 4: Introduction

    Introduction The MS6720 is the first laser bar code scanner truly to bridge the gap between omnidirectional fixed projection and hand-held scanners. It incorporates fixed projection performance and our patented 20-line scan pattern into a comfortable, ergonomic styling of our popular hand-helds. With this design, Metrologic has engineered a scanner that transcends any other on the market today.
  • Page 5: Scanner And Accessories

    Scanner and Accessories following is a list of the parts included in the MS6720 kit. MS6720 Hand-Held Laser Scanner - Refer to page 27 for available communication protocols Stand (MLPN 45967) - Refer to page 8 for available kits Optional Power Transformer 120V or 220V or 240V (AC in)
  • Page 6: Quick Start

    Note: Any time the Load Defaults bar code is scanned the MS6720 is configured for an RS-232 interface. If a RS-232 is not being used, scan at least one other bar code to enable Keyboard Wedge, OCIA, Light Pen or 46xx.
  • Page 7: Operational Test

    Operational Test If the scanner is to receive power from an external power supply, test the scanner before it is connected to the host system. Keyboard Wedge Scanners: Plug one end of the coil cable into the keyboard connector on the PC.
  • Page 8: Scanner Installation: Powered By External Power Supply

    When the scanner first receives power, both LEDs come on together along with the beep-the green LED only flashes. b. Plugging the scanner into the serial port of the PC does not guarantee that scanned information will appear at the PC. A software driver and correct configuration setting are also required for proper communication to occur.
  • Page 9: Scanner Installation: Powered By The Host Device

    Scanner Installation: Powered by Host Device If the host system supplies +5VDC power to the scanner, reposition the internal jumper within the MCA (Metrologic Connector Adaptor) before connecting the scanner to the host device. In addition, plug the 4 position ground jumper into the power supply connector located on the side of the MCA.
  • Page 10: Scanner Installation To The Pc For The Scanner With Built-In Pc Keyboard Wedge Interface

    6-pin mini DIN male on the other. Also included with the MS6720 is an adaptor cable with a 5-pin male DIN on one end and a 6-pin female mini DIN on the other to mate to a specific keyboard.
  • Page 11: The Ms6720 Stand

    (also included is the wall mount clip). The instruc- tions for use of the wall mount clip are included with the general assembly instructions for the stand. Listed below are the component parts of the MS6720 stand kits. 1) Complete Stand Kit:...
  • Page 12: Scanner Parts

    When the green light turns off, communica- tion to the host is complete. The green LED blinks while the scanner is waking up from an IR sensor timeout. The LED’s are also used as diagnostic indicators and mode indicators.
  • Page 13: Audible Indicators

    Audible Indicators When the MS6720 scanner is in operation, it provides audible feedback. These sounds indicate the status of the scan and scanner. Four settings are available for the tone of the beep. To change the tone, refer to the Program- ming Guide section: Beeper Tones.
  • Page 14: Failure Modes

    Return the unit for repair at an authorized service center. Three Beeps - on power up If the scanner beeps 3 times on power up then, the non volatile memory which holds the scanner configuration has failed. Return the unit for repair at an authorized service...
  • Page 15: Visual Indicators

    Visual Indicators There are a red LED and a green LED on the scanner. When the scanner is on, the flashing or stationary activity of the LEDs indicates the status of the scan and scan-ner. No Red or Green LED There are two reasons why the LEDs will not be illuminated: 1.) If the scanner is receiving power and the LEDs are not on, then...
  • Page 16: Label

    Label Each scanner has a label located on the bottom of the unit. This label contains information such as the model number, date of manufacture, serial number, and approvals. This label also notes that the device is a CDRH Class IIa laser product. The following is an example of this label:...
  • Page 17: Depth Of Field Specifications

    Depth of Field Specifications Normal Depth of Field...
  • Page 18: Short Depth Of Field

    Short Depth of Field...
  • Page 19: Extended Depth Of Field

    Extended Depth of Field...
  • Page 20: Optional Depth Of Field

    Optional Depth of Field...
  • Page 21: Automatic Turn-On Specifications

    Automatic Turn-On Specifications (IR Sensor) Normal Depth of Field Short Depth of Field Note: Depth of Field based on 13mil (.013") minimum element width, Turn On Range is nominal; small variances do NOT indicate a malfunction.
  • Page 22: Scan Pattern Specifics

    Scan Pattern Specifics Projection Axis The scan pattern of the MS6720 exits straight out of the scanner. This feature was purposefully designed to provide pointing efficiency in the hand held mode and instinctive positioning in the fixed presentation mode. Omnidirectional Scan Volume Note: The above scan volume shows omnidirectional volume.
  • Page 23: Cross-Sectional Scan Pattern

    Cross-Sectional Scan Pattern...
  • Page 24: Maintenance

    Maintenance Smudges and dirt can interfere with the proper scanning of a bar code. Therefore, the output window will need occasional cleaning. 1. Spray glass cleaner onto lint free, non-abrasive cleaning cloth. 2. Gently wipe the scanner window.
  • Page 25: All Interfaces

    Check transformer, outlet and power or motor spin strip NOTE: If it’s a direct connect scanner, the problem could be inadequate power being supplied to the scanner. It may be necessary to use a Metrologic transformer for power. Check the fuse in the MCA.
  • Page 26 Disable IR sleep mode Unit scans bar wake up requires full Disable IR sleep mode code too slowly motor spin up for operation upon waking up NOTE: Disabling the IR sleep mode allows the scanner to respond to bar codes quicker SOLUTION...
  • Page 27 The unit powers up properly, lasers come on, but the unit does not scan and does not beep when a bar code is presented POSSIBLE CAUSE(S)/SOLUTION(S) Improper settings can be the cause for a scanner not to scan. The following would be typical examples: 1. Scanning a particular symbology that is not enabled. (UPC/EAN, Code 39, Interleaved 2 of 5, Code 93, Code 128 and Codabar are enabled by default.)
  • Page 28: Keyboard Wedge Only

    Alpha characters Computer is in Caps Lock Enable Caps Lock detect setting of show as lower mode the scanner to detect whether PC is case operating in Caps Lock Everything These characters may not be Try operating the scanner in Alt works except for supported by that country’s...
  • Page 29 This program is for demonstration purposes only. It is only intended to prove that cabling is correct, the comx port is working, and the scanner is working. If the bar code data displays on the screen while using this program, it only demon-strates that the hardware interface and scanner are working.
  • Page 30: Application And Protocols

    Light Pen Emulation (LTPN) 6720 Keyboard Wedge (KBW) The MS6720 Hand-Held Laser Scanner with Built-in PC Keyboard Wedge Interface is designed to be used for keyboard emulation only. However, many RS-232 programmable functions that are available in other Metrologic scanners are also available as keyboard wedge functions.
  • Page 31: Design Specifications

    Appendix A Design Specifications Application: Fixed Projection/Hand-Held Laser Bar Code Scanner Max. Radiant Power: 0.681 Milliwatts (PEAK) Light Source: VLD 675 ± 5nm CDRH: Class IIa laser product EN 60950: 1993, EN 60825-1:1994/A11:1996, Laser Class 1, EN 55022:1987 Class A, EN...
  • Page 32 Operational Depth of Field: 0" - 4"; 0"- 8" (programmable) 0 - 101.6mm; 0 - 203.2mm Scan Speed: 1000 scan lines per second Scan Pattern: 5 fields of 4 parallel lines Scan Lines: Min Bar Width: 5.2 mil Indicators (LED): red = laser on, ready to scan green = good read, decoding Beeper Operation:...
  • Page 33: Default Settings

    The scanner is shipped from the factory programmed to a set of default conditions. The default parameter of the scanner has an asterisk ( * ) in the charts on the following pages. If an asterisk is not in the default column then the default setting is Off or Disabled.
  • Page 34 Parameter Default OCIA RS-232* DTS/NIXDORF NCR F NCR S Poll Light Pen Source Beeper Tone Normal Beep/Transmit Sequence Before Transmit Communication Timeout None Razzberry Tone on Timeout Three Beeps on Timeout No Beeps on Timeout IR Timeout 10 Min. Same Symbol Rescan Timeout: 200 msecs Same Symbol Rescan Timeout: 500 msecs...
  • Page 35 Parameter Default OCIA RS-232* Transmit Mod 10/ITF Transmit MSI-Plessey Check Characters Parity Space Baud Rate 9600 8 Data Bits 7 Data Bits Transmit Sanyo ID Characters Nixdorf ID Shell Schulmberger Formatting UPC Prefix UPC Suffix Transmit AIM ID Characters STX Prefix ETX Suffix Carriage Return Line Feed...
  • Page 36 Parameter Default OCIA RS-232* 977 (2 digit) Supplemental Requirement Supplements are not Required Two Digit Redundancy Five Digit Redundancy 200 msec to Find Supplement 100 msec to Find Supplement Coupon Code 128 Ligh t Pen 46XX code...
  • Page 37: Pin Assignments

    Cable Pin Assignments for the Coil Cable The MS6720 scanners are terminated to a 10 position shielded modular connector. All of the coil cables (MLPN 44530) for the MS6720 scanner are terminated the same. The difference between versions is the end of the cable going into the scanner.
  • Page 38 +5VDC Power to Scanner +5VDC Power to Scanner *When the host supplies power to the scanner, this is the pin assignment for the +5VDC for the scanner. If, in the application, the host device will supply the power necessary for the scanner, reposition an internal jumper within the MCA and plug the 4 position ground jumper to the power supply connector for FCC and ESD purposes.
  • Page 39: Pin Assignments

    Pin Assignments for the 5-pin DIN and 6-pin mini-DIN MS6720 Hand- Held Laser Scanner with Built-in PC Keyboard Wedge Interface The coil cable is terminated with a 5-pin DIN female connector on one end, and a 6-pin mini DIN male on the other. Metrologic will supply an adaptor cable with a 5-pin DIN male connector on one end and a 6-pin mini DIN female connector on the other.
  • Page 40: Warranty And Disclaimer

    Appendix D Warranty and Disclaimer Limited Warranty Products manufactured by Metrologic have a 2-year limited warranty from date of manufacture. In the event that it is determined that the equipment failure is covered under the warranty, Metrologic shall, as its sole option, repair, replace with a functionally equivalent unit, or refund an amount equal to the purchase price to the original purchaser, whether distributor, dealer/reseller, or retail consumer, and return the equipment to the customer without charge for service or return freight.
  • Page 41 Disclaimer Metrologic Instruments, Inc. and the author or authors make no claims or warranties with respect to the contents or accuracy of this publication, or the product it describes, including any warranties of fitness or merchantability for a particular purpose. Any stated or expressed warranties are in lieu of all obligations or liability for any damages, whether special, indirect, or consequential, arising out of or in connection with the use of this publication or the product it describes.
  • Page 42: Notices

    Under no circumstances should the customer attempt to service the laser scanner. Never attempt to look at the laser beam, even if the scanner appears to be nonfunctional. Never open the scanner in an attempt to look into the device. Doing so could result in hazardous laser light exposure.
  • Page 43 Umständen versuchen, den Laser-Scanner selbst zu warten. Sehen Sie niemals in den Laserstrahl, selbst wenn Sie glauben, daß der Scanner nicht aktiv ist. Öffnen Sie niemals den Scanner, um in das Gerät hineinzusehen. Wenn Sie dies tun, können Sie sich einer lebensgefährlichen Laserstrahlung aussetzen.
  • Page 44: Patents

    Appendix F Patents “Patent Information This METROLOGIC product may be covered by one or more of the following U.S. Patents: U.S. Patent No. 4,360,798; 4,369,361; 4,387,297; 4,460,120; 4,496,831; 4,593,186; 4,607,156; 4,673,805; 4,736,095; 4,758,717; 4,816,660; 4,845,350; 4,896,026; 4,923,281; 4,933,538; 4,992,717; 5,015,833; 5,017,765;...
  • Page 45: Index

    Index Accessories Cross sectional scan pattern AC input/outlet 2, 4, 5, 7 Adaptor Current 7, 28 cable 2, 7, 36 Customer service 37 5M 6F 7 2, 4-6 Application 2, 27, 28, 35 DC transformer Approvals Decode capability 29 Assignments Default Settings 30-33 34-36 Depth of field...
  • Page 46 RS-232 2-4, 26, 27, 29-35 Normal depth of field 14, 18 Scan lines Notices 39, 40 Scan pattern(s) Scan speed Scan volume OCIA 2-4, 27, 29-35 Scanner installation Omindirectional scan volume ScanSelect manual 25-27 Operating current 28 SELV Operating temperature Service 37 Operation Shock...
  • Page 47 System interfaces 29 Termination 34-36 Test Transformers Troubleshooting 22-26 Tones 10-12, 29 Turn-on specifications Ventilation Version 27, 34, 35 Visual indicators 12 Voltage 4, 5, 7, 28 Warranty 22, 37 Watt Weight 28 Window 21...

Table of Contents