Whirlpool CHW8990CW Installation Instructions Manual page 12

CODE
VAULT VIEWING OPTION
A. 00
This option is either SELECTED 'ON' or NOT
SELECTED 'OFF'.
A. 00 Not Selected 'OFF'.
A. SC Selected 'ON'. Press the COLD button once for
this selection. When selected, the money and/or
cycle counts will be viewable (if counter option(s)
is selected) when the coin box is removed.
g Press the WARM button once to advance
to next code.
b. 05 VALUE OF COIN 1
b. 05 This represents the value of coin 1 in number
of nickels: 05 = $0.25.
By pressing the HOT button, there is an option
of 1–199 nickels.
g Press the WARM button once to advance
to next code.
C. 20 VALUE OF COIN 2
C. 20 This represents the value of coin 2 in number
of nickels: 20 = $1.00.
C. 05 By pressing the HOT button, there is the option
of 1–199 nickels.
Press the WARM button once to advance
g
to next code.
d. 00 COIN SLIDE OPTION
This option is either SELECTED 'ON' or NOT
SELECTED 'OFF'. Replacement of meter case will
be needed for coin slide mounting.
d. 00 Not Selected 'OFF'.
Selected 'ON'. NOTE: This option needs to be set
d. CS
to '00' unless the meter case has been changed to
accept a coin slide device. Press the COLD button
3 consecutive times for this selection.
When coin slide mode is selected, set 'b'. equal to
value of vend price in nickels. Set set-up code 6 xx
(regular cycle price) and set-up code 3.xx (special
cycle price) to number of slide operations. If the
installer sets-up 'CS' and a coin drop mechanism is
installed, the washer will not register coins that are
inserted.
Press the WARM button once to advance
g
to next code.
ADD COINS OPTION
E. 00
This option is either SELECTED 'ON' or NOT
SELECTED 'OFF'. This option causes the customer
display to show the number of coins (coin 1) to
enter, rather than the dollars-and-cents amount.
E. 00 Not Selected 'OFF'.
E. AC Selected 'ON'. Press the COLD button
3 consecutive times for this selection.
g Press the WARM button once to advance
to next code.
12
EXPLANATION CODE
ENHANCED PRICING OPTION
F. 00
F. 00 Not Selected 'OFF'.
F. CP Cycle-Based pricing enabled. This option allows
configuration of different prices for cycles that use
cold, warm, and hot water wash cycles.
Press the WARM button once to advance
g
to next code.
J. Cd COIN/DEBIT OPTION
J. Cd Both coin and debit selected. Press the COLD
button 3 consecutive times for this selection.
J. C_ Coins selected, debit disabled. Press the COLD
button 3 consecutive times for this selection.
J. Ed Enhanced Debit is self-selected when a Generation
2 card reader is installed in the washer. The Ed
option cannot be manually selected or deselected.
Press the WARM button once to advance
g
to next code.
PRICE SUPPRESSION OPTION
L. 00
This option causes the customer display to show
'ADD' or 'AVAILABLE' rather than the amount of
money to add. (Used mainly in debit installations.)
L. 00 Not Selected 'OFF.'
L. PS Selected 'ON.' Press the COLD button once for this
selection.
Press the WARM button once to advance
g
to next code.
CLEAR ESCROW OPTION
n. CE
When selected, money held in escrow for
30 minutes without further escrow or cycle activity
will be cleared.
n 00 Not Selected 'OFF'.
n CE Selected 'ON'. Press the COLD button once for this
selection.
Press the WARM button once to advance
g
to next code.
r. 800 TOP SPIN SPEED RPM
r. 800 This can be selected from the following spin
speeds: 600 rpm, 750 rpm, 800 rpm, 1000 (displays
as 999) rpm. Step between speeds by pressing
the HOT button. Factory default of 800 rpm.
g Press the WARM button once to advance
to next code.
U. 00 PENNY INCREMENT OFFSET
U. 00 This represents the penny increment price offset
used in Generation 2 (Enhanced Debit) Smart Card
Readers. Choose from 0–4 pennies by pressing the
HOT button.
g Press the WARM button once to advance
to next code.
EXPLANATION