Related Manuals for Samsung S29E790C
Summary of Contents for Samsung S29E790C
- Page 1 Monitor User Manual S29E790C The color and the appearance may differ depending on the product, and the specifications are subject to change without prior notice to improve the performance. BN46-00442C-01...
-
Page 2: Table Of Contents
Table of contents Before Using the Product Connecting and Using a Source Screen Setup Device Copyright SAMSUNG MAGIC Bright Configuring SAMSUNG MAGIC Bright Before Connecting Securing the Installation Space Pre-connection Checkpoints Precautions for storage Brightness Configuring Brightness Connecting and Using a PC... - Page 3 Configuring Source Detection Troubleshooting Guide Display Time Key Repeat Time Configuring Display Time Configuring Key Repeat Time Requirements Before Contacting Samsung Customer Service Center Power LED On Testing the Product Configuring Power LED On Checking the Resolution and Frequency Check the following.
- Page 4 Table of contents Specifications General PowerSaver Standard Signal Mode Table Appendix Contact SAMSUNG WORLD WIDE Responsibility for the Pay Service (Cost to Customers) Not a product defect A Product damage caused by customer's fault 86 Others Terminology...
-
Page 5: Before Using The Product
ⓒ 2015 Samsung Electronics Samsung Electronics owns the copyright for this manual. Use or reproduction of this manual in parts or entirety without the authorization of Samsung Electronics is prohibited. Microsoft, Windows are registered trademarks of Microsoft Corporation. VESA, DPM and DDC are registered trademarks of the Video Electronics Standards Association. -
Page 6: Securing The Installation Space
High-glossy models can develop white stains on the surface if an ultrasonic wave humidifier is used A serious or fatal injury may result if instructions are not followed. nearby. ― Contact your nearest Samsung Customer Service Center if you want to clean the inside of the product Caution (Service fee will be charged.) Personal injury or damage to properties may result if instructions are not followed. -
Page 7: Cleaning
Cleaning Electricity and Safety ― Exercise care when cleaning as the panel and exterior of advanced LCDs are easily scratched. ― The following images are for reference only. Real-life situations may differ from what is shown in the images. ― Take the following steps when cleaning. ―... -
Page 8: Installation
Install the product at least 10cm away from the wall to allow ventilation. • An increased internal temperature may cause a fire. Only use the power cord provided with your product by Samsung. Do not use the power cord with other products. - Page 9 SAMSUNG • Be sure to consult Samsung Customer Service Center if you want to install the product at such a place.
-
Page 10: Operation
If the product is dropped or the outer case is damaged, turn off the power • Product failure, an electric shock or fire may result from a damaged and disconnect the power cord. Then contact Samsung Customer Service cable. Center. - Page 11 • Be sure to power off the product and disconnect the power cord when water or other foreign substances have entered the product. Then contact Samsung Customer Service Center. • Product failure, an electric shock or fire may result. Do not put DC power adapters together.
- Page 12 Do not put the DC power adapter near to any heating apparatus. Do not touch the screen when the product has been turned on for an extended period of time as it will become hot. • Otherwise, a fire may result. Keep the DC power adapter in a well-ventilated area.
-
Page 13: Correct Posture To Use The Product
Correct posture to use the product Use the product in the correct posture as follows: • Straighten your back. • Allow a distance of 45 to 50cm between your eye and the screen, and look slightly downward at the screen. Keep your eyes directly in front of the screen. •... -
Page 14: Preparations
Chapter 02 Preparations Checking the Components Components - Contact the vendor where you purchased the product if any components are missing. ― Components may vary depending on the country. - The appearance of the components may differ from the images shown. - Using the HDMI cable that came with the package is recommended. -
Page 15: Parts
Parts Control Panel ― The color and shape of parts may differ from what is shown. Specifications are subject to change without notice to improve quality. JOG Button Function Key Guide LEFT RIGHT DC 14V HDMI IN 1 HDMI IN 2 DP IN SERVICE PRESS(ENTER) -
Page 16: Direct Key Guide
― The shortcut button screen (OSD menu) shown below is displayed only when the monitor screen is turned on, the Direct Key guide computer resolution changes, or the input source changes. UP/DOWN: Adjust Brightness, Contrast, Sharpness. LEFT/RIGHT: Adjust Volume. Brightness PRESS(ENTER): Display Function Key Guide. -
Page 17: Function Key Guide
Function Key Guide UP/DOWN/LEFT/RIGHT: Move to the item you want. The description for each item will appear when the focus changes. PRESS(ENTER): The selected item will be applied. ― To enter the main menu or to use other items, press the JOG button to display Icons Description the Function Key Guide. - Page 18 ― When the monitor displays nothing (i.e. Power saving mode or Non-signal mode), 2 direct keys for control source and power could be used as below. JOG Button Power saving/Non-signal mode Source Change Down Power Off PRESS(ENTER) for 2 seconds ―...
-
Page 19: Reverse Side
Port Description Reverse Side Connects to the DC power adapter. ― The color and shape of parts may differ from what is shown. Specifications are DC 14V subject to change without notice to improve quality. Connects to a source device using an HDMI cable or HDMI-DVI cable. HDMI IN 1 HDMI IN 2 Connects to a source device using a DP cable. -
Page 20: Installation
Installation Adjusting the Product Tilt and Height ― The color and shape of parts may differ from what is shown. Specifications are subject to change without notice to improve quality. -2˚(±2˚) ~ 20˚(±2˚) 100.0 mm ± 2.0 mm • The monitor tilt and height can be adjusted. •... - Page 21 ― The color and shape of parts may differ from what is shown. Specifications are subject to change without notice to improve quality. Caution Take extra care to ensure your hand does not get stuck in the height adjustment area. This could injure your hand. Do not put the hand below the stand body.
-
Page 22: Anti-Theft Lock
Anti-theft Lock ― An anti-theft lock allows you to use the product securely even in public places. ― The locking device shape and locking method depend on the manufacturer. Refer to the user guide provided with your anti-theft locking device for details. To lock an anti-theft locking device: DC 14V HDMI IN 1... -
Page 23: Connecting And Using A Source Device
Chapter 03 Connecting and Using a Source Device Before Connecting Connecting and Using a PC Check the following before you connect this product with other devices. Select a connection method suitable for your PC. ― Connecting parts may differ in different products. Pre-connection Checkpoints Connection Using the HDMI Cable ―... -
Page 24: Connection Using The Dp Cable
Connection Using the DP Cable Connecting to Headphones or Speakers ― Do not connect the power cable before connecting all other cables. ― Do not connect the power cable before connecting all other cables. Ensure you connect a source device first before connecting the power cable. Ensure you connect a source device first before connecting the power cable. -
Page 25: Connecting The Power
Connecting the Power Power connection using detachable DC power adapter DC 14V HDMI IN 1 HDMI IN 2 DP IN SERVICE DC 14V HDMI IN 1 HDMI IN 2 DP IN SERVICE Connect the power cable to the DC power adapter. Then, connect the DC power adapter to the DC 14V port on the back of the product. Next, connect the power cable to the power outlet. -
Page 26: Tidying Up The Connected Cables
Tidying Up the Connected Cables To remove the COVER-CABLE, hold and pull the COVER-CABLE Hold the bottom of the stand neck securely with your left with your thumb and index finger in the arrow direction while hand and use the thumb of your right hand to slide up the holding the stand with the other hand. -
Page 27: Driver Installation
― An installation driver is contained on the CD supplied with the product. Select a language on the product and change the resolution on your PC to the optimum setting. ― If the file provided is faulty, visit the Samsung homepage (http://www.samsung.com/) and download the file. -
Page 28: Screen Setup
Configure the screen settings such as brightness. A detailed description of each function is provided. Refer to your product for details. SAMSUNG MAGIC Bright Configuring SAMSUNG MAGIC Bright When the Function Key Guide appears, select by moving the JOG button UP. Next, press the JOG button. - Page 29 When the external input is connected through HDMI/DP and PC/AV Mode is set to AV, Bright has four automatic picture SAMSUNG MAGIC settings (Dynamic, Standard, Movie and Custom) that are preset at the factory. You can activate either Dynamic, Standard, Movie or Custom.
-
Page 30: Brightness
Move to controlling the JOG button UP/DOWN and press the JOG button. ― This menu is not available when Bright Dynamic Contrast is set to SAMSUNG MAGIC mode. Brightness Move to controlling the JOG button UP/DOWN and press the JOG button. -
Page 31: Contrast
Move to controlling the JOG button UP/DOWN and press the JOG button. ― This option is not available when Bright Cinema Dynamic is in SAMSUNG MAGIC Contrast mode. Contrast Move to controlling the JOG button UP/DOWN and press the JOG button. -
Page 32: Sharpness
Move to controlling the JOG button UP/DOWN and press the JOG button. ― This option is not available when Bright Cinema Dynamic is in SAMSUNG MAGIC Contrast mode. Sharpness Move to controlling the JOG button UP/DOWN and press the JOG button. -
Page 33: Color
Picture Move to controlling the JOG button UP/DOWN and press the JOG button. ― Adjust the tint of the screen. This menu is not available when Bright is set SAMSUNG MAGIC Cinema Dynamic Contrast mode. Color Move to controlling the JOG button UP/DOWN and press the JOG button. -
Page 34: Hdmi Black Level
• Low: Select this mode to reduce the black level and increase the white level when there is a contrast ratio degradation. Move to the desired option controlling the JOG button UP/DOWN and press the JOG button. Picture Optimize HDMI picture brightness SAMSUNG MAGIC Bright Custom The selected option will be applied. and contrast by... -
Page 35: Eye Saver Mode
TÜV Rheinland and certified as it met the requirements of TÜV Rheinland “Low Blue Light Content” standards. The selected option will be applied. Picture Set to an optimum picture quality SAMSUNG MAGIC Bright Custom suitable for eye relaxation. Brightness... -
Page 36: Game Mode
Game Mode Configuring Game Mode When the Function Key Guide appears, select by moving the JOG button UP. Next, press the JOG button. Configure the product screen settings for game mode. Picture Use this feature when playing games on a PC or when a game console such as Move to controlling the JOG button UP/DOWN and press the JOG button. -
Page 37: Response Time
Response Time Configuring the Response Time When the Function Key Guide appears, select by moving the JOG button UP. Next, press the JOG button. Accelerate the panel response rate to make video appear more vivid and natural. ― It is best to set Picture Response Time Standard... -
Page 38: Picture Size
Picture Size Changing the Picture Size When the Function Key Guide appears, select by moving the JOG button UP. Next, press the JOG button. Change the picture size. ― This menu is not available when Picture PIP/PBP Mode is set to and the Size is set... - Page 39 mode mode • 4:3: Display the picture with an aspect ratio of 4:3. Suitable for videos and standard broadcasts. Picture Choose the size and • 16:9: Display the picture with an aspect ratio of 16:9. aspect ratio of the Game Mode •...
-
Page 40: Screen Adjustment
Screen Adjustment Configuring H-Position & V-Position H-Position: Move the screen to the left or right. ― This menu is only available when Picture Size is set to Screen Fit Mode. V-Position: Move the screen up or down. When a 480P or 576P or 720P or 1080P signal is input in mode and the When the Function Key Guide appears, select by moving the JOG button UP. -
Page 41: Configuring The Pip/Pbp Settings
Chapter 05 Configuring the PIP/PBP Settings PIP/PBP The PIP (Picture in Picture) function separates the screen into two parts. One source device is displayed on the main screen at the same time the another source device is displayed in inset windows. The PBP (Picture by Picture) function separates the screen in half displaying output from two different source devices simultaneously on the left and right sides of the screen. -
Page 42: Configuring Pip/Pbp Mode
Configuring PIP/PBP Mode Enable or disable the PIP/PBP Mode function. When the Function Key Guide appears, select by moving the JOG button UP. Next, press the JOG button. PIP/PBP Turn PIP/PBP Mode Move to the PIP/PBP controlling the JOG button UP/DOWN and press the JOG button. on or off. -
Page 43: Configuring Size
Configuring Size Select the size and aspect ratio of the sub-screen. When the Function Key Guide appears, select by moving the JOG button UP. Next, press the JOG button. PIP/PBP Select the size and Move to the PIP/PBP controlling the JOG button UP/DOWN and press the JOG button. aspect ratio of the PIP/PBP Mode sub-screen. -
Page 44: Configuring Position
Configuring Position Select the position of the sub-screen from the available options. When the Function Key Guide appears, select by moving the JOG button UP. Next, press the JOG button. PIP/PBP Select the position Move to the PIP/PBP controlling the JOG button UP/DOWN and press the JOG button. of the sub-screen PIP/PBP Mode from the available... -
Page 45: Configuring Sound Source
Configuring Sound Source Set which screen you want to hear the sound for. When the Function Key Guide appears, select by moving the JOG button UP. Next, press the JOG button. PIP mode Move to the PIP/PBP controlling the JOG button UP/DOWN and press the JOG button. PIP/PBP Set which screen Sound Source... -
Page 46: Configuring Source
Configuring Source Select the source for each screen. When the Function Key Guide appears, select by moving the JOG button UP. Next, press the JOG button. PIP Mode Move to the PIP/PBP controlling the JOG button UP/DOWN and press the JOG button. (available in PIP mode(Size Source... - Page 47 PBP Mode Select input sources for the devices displayed on the main and sub screens. When the Function Key Guide appears, select by moving the JOG button UP. Next, press the JOG button. (available in PBP mode(Size Move to the PIP/PBP controlling the JOG button UP/DOWN and press the JOG button.
-
Page 48: Configuring Picture Size
Configuring Picture Size Select the image size for sub-screen. When the Function Key Guide appears, select by moving the JOG button UP. Next, press the JOG button. PIP Mode Move to the PIP/PBP controlling the JOG button UP/DOWN and press the JOG button. (available in PIP mode(Size Picture Size... - Page 49 PBP Mode Set the Picture Size for each of the divided screens. When the Function Key Guide appears, select by moving the JOG button UP. Next, press the JOG button. (available in PBP mode(Size Move to the PIP/PBP controlling the JOG button UP/DOWN and press the JOG button. mode Picture Size Move the JOG button UP/DOWN to select...
- Page 50 mode mode • 4:3: Display the picture of the sub-screen with an aspect ratio of 4:3. Suitable for videos and standard broadcasts. Picture Size • 16:9: Display the picture of the sub-screen with an aspect ratio of 16:9. • 21:9: Display the picture of the sub-screen with an aspect ratio of 21:9. Screen Fit: Display the picture of the sub-screen with the original aspect ratio without cutting anything off.
-
Page 51: Configuring Contrast
Configuring Contrast Adjust the contrast level for sub-screen. When the Function Key Guide appears, select by moving the JOG button UP. Next, press the JOG button. PIP Mode Move to the PIP/PBP controlling the JOG button UP/DOWN and press the JOG button. (available in PIP mode(Size Contrast... - Page 52 PBP Mode Adjust the contrast level for each screen. When the Function Key Guide appears, select by moving the JOG button UP. Next, press the JOG button. (available in PBP mode(Size Move to the PIP/PBP controlling the JOG button UP/DOWN and press the JOG button. PIP/PBP Adjust the contrast Contrast...
-
Page 53: Coordinating Osd
Chapter 06 Coordinating OSD A detailed description of each function is provided. Refer to your product for details. Transparency Changing Transparency When the Function Key Guide appears, select to display the corresponding menu screen. Set the transparency for the menu windows. Move to OnScreen Display controlling the JOG button UP/DOWN and press the JOG button. -
Page 54: Language
Language Configuring Language When the Function Key Guide appears, select by moving the JOG button UP. Next, press the JOG button. Set the menu language. ― A change to the language setting will only be applied to the onscreen menu OnScreen Display Move to controlling the JOG button UP/DOWN and press the JOG button. -
Page 55: Display Time
Display Time Configuring Display Time When the Function Key Guide appears, select to display the corresponding menu screen. Set the on-screen display (OSD) menu to automatically disappear if the menu is not used for a specified period of time. OnScreen Display Move to controlling the JOG button UP/DOWN and press the JOG button. -
Page 56: Setup And Reset
Chapter 07 Setup and Reset A detailed description of each function is provided. Refer to your product for details. Sound Configuring Volume When the Function Key Guide appears, select by moving the JOG button UP. Next, press the JOG button. System Move to System... -
Page 57: Configuring Sound Mode
Configuring Sound Mode When the Function Key Guide appears, select by moving the JOG button UP. Next, press the JOG button. System Move to controlling the JOG button UP/DOWN and press the JOG button. Sound Sound Move to controlling the JOG button UP/DOWN and press the JOG button. Volume Sound Mode Standard... -
Page 58: Configuring Select Sound
Configuring Select Sound When the Function Key Guide appears, select by moving the JOG button UP. Next, press the JOG button. System Move to controlling the JOG button UP/DOWN and press the JOG button. Sound Volume Sound Move to controlling the JOG button UP/DOWN and press the JOG button. Sound Mode Move to Select Sound... -
Page 59: Eco Saving Plus
― This option is not available when Bright is in Dynamic Contrast mode. SAMSUNG MAGIC System Adjust the power ― This menu is not available when Game Mode is enabled. -
Page 60: Off Timer
Off Timer Configuring Off Timer When the Function Key Guide appears, select by moving the JOG button UP. Next, press the JOG button. You can set the product to automatically turn off. Move to System controlling the JOG button UP/DOWN and press the JOG button. System Enable or disable the Off Timer. -
Page 61: Configuring Turn Off After
Configuring Turn Off After Off Timer Set the monitor to automatically turn Off Timer ― This option is only available when Off Timer is set to On. off after a certain Turn Off After time period. When the Function Key Guide appears, select by moving the JOG button UP. -
Page 62: Pc/Av Mode
PC/AV Mode ― Supplied for the wide models only such as 16:9 or 16:10. ― If the monitor is in HDMI HDMI 2 DisplayPort mode and the screen says Check Signal Cable or power saving mode activates, press the JOG button to display the function-button screen and then select the icon. -
Page 63: Displayport Ver
DisplayPort Ver. ― Incorrect settings may cause the screen to go blank. If this occurs, check the device specifications. ― If the monitor is in HDMI HDMI 2 DisplayPort mode and the screen says Check Signal Cable or power saving mode activates, press the JOG button to display the function-button screen and then select the icon. -
Page 64: Source Detection
Source Detection Configuring Source Detection When the Function Key Guide appears, select by moving the JOG button UP. Next, press the JOG button. You can activate Source Detection. ― Not available when PIP/PBP Mode is set to On. Move to System controlling the JOG button UP/DOWN and press the JOG button. -
Page 65: Key Repeat Time
Key Repeat Time Configuring Key Repeat Time When the Function Key Guide appears, select by moving the JOG button UP. Next, press the JOG button. Control the response rate of a button when the button is pressed. Move to System controlling the JOG button UP/DOWN and press the JOG button. -
Page 66: Power Led On
Power LED On Configuring Power LED On When the Function Key Guide appears, select by moving the JOG button UP. Next, press the JOG button. Configure the settings to enable or disable the power LED located at the lower part of the product. Move to System controlling the JOG button UP/DOWN and press the JOG button. -
Page 67: Reset All
Reset All Initializing Settings (Reset All) When the Function Key Guide appears, select by moving the JOG button UP. Next, press the JOG button. Return all the settings for the product to the default factory settings. Move to System controlling the JOG button UP/DOWN and press the JOG button. System Return all the settings for the... -
Page 68: Information Menu And Others
Chapter 08 Information Menu and Others A detailed description of each function is provided. Refer to your product for details. Information Information Picture LS29E790CNS/EN PIP/PBP View the current input source, frequency and resolution. OnScreen Display Displaying Information System HDMI 1 DisplayPort ****x**** ****x****... -
Page 69: Configuring Brightness, Contrast And Sharpness From The Initial Screen
Configuring Brightness, Contrast Brightness ― This menu is not available when Bright is set to Dynamic Contrast mode. SAMSUNG MAGIC and Sharpness from the Initial ― This menu is not available when Eco Saving Plus is enabled. Screen Contrast ― This menu is not available when... -
Page 70: Configuring Volume In The Initial Screen
Configuring Volume in the Initial Volume Screen Volume Adjust the controlling the JOG button LEFT/RIGHT. ― If the audio quality of a connected input device is poor, the Auto Mute function on the product may mute the sound or Volume You can adjust by moving the JOG button left or right, if no OSD menu is cause choppy audio when applying the headphones or speakers. -
Page 71: Installing The Software
Chapter 09 Installing the Software Easy Setting Box Restrictions and Problems with the Installation (Easy Setting Box) The Easy Setting Box installation may be affected by the Graphics Card, Motherboard and the Networking Environment. Easy Setting Box System Requirements Easy Setting Box enables users to use the monitor by partitioning multiple sections. •... -
Page 72: Troubleshooting Guide
Chapter 10 Troubleshooting Guide Requirements Before Contacting Samsung Customer Service Center Testing the Product Before calling Samsung Customer Service Center, test your product as follows. If the problem persists, contact Samsung Check if your product is operating normally by using the product test function. -
Page 73: Check The Following
Check the following. Installation issue (PC mode) Issues Solutions The screen keeps switching on and off. Check the cable connection between the product and PC, and ensure the connectors are locked. Blank spaces are found on all four sides of the screen when The blank spaces found on the screen have nothing to do with the product. - Page 74 Issues Solutions The screen is not clear. The screen is blurry. Remove any accessories (video extension cable, etc.) and try again. Set the resolution and frequency to the recommended level. The screen appears unstable and shaky. Check that the resolution and frequency for the PC are within the range of resolution and frequency compatible with the product.
- Page 75 Sound issue Issues Solutions There is no sound. Check the connection of the audio cable or adjust the volume. Check the volume. The volume is too low. Adjust the volume. If the volume is still low after turning it up to the maximum level, adjust the volume on your PC sound card or software program.
-
Page 76: Q & A
Q & A Question Answer Refer to the user manual for your PC or graphics card for further instructions on adjustment. How can I change the frequency? Set the frequency on your graphics card. • Windows XP: Go to Control Panel Appearance and Themes Display Settings... - Page 77 Question Answer How do I set power-saving mode? • Windows XP: Set power-saving mode in Control Panel Appearance and Themes Display Screen Saver Settings or BIOS SETUP on the PC. • Windows ME/2000: Set power-saving mode in Control Panel Display Screen Saver Settings or BIOS SETUP on the PC.
-
Page 78: Specifications
Chapter 11 Specifications General Size Model Name S29E790C Panel Size 29 Class (28.7 Inches / 73 cm) Display area 672.768 mm (H) x 283.824 mm (V) 26.5 Inches (H) x 11.2 Inches (V) Display area Pixel Pitch 0.2628 mm (H) x 0.2628 mm (V) 0.010346 Inches (H) x 0.010346 Inches (V) - Page 79 ― Due to the nature of the manufacturing of this product, approximately 1 pixel per million (1ppm) may appear brighter or darker on the panel. This does not affect product performance. ― This device is a Class B digital apparatus. (USA only) Dispose unwanted electronics through an approved recycler. To find the nearest recycling location, go to our website: www.samsung.com/recyclingdirect or call, (877) 278 - 0799...
-
Page 80: Powersaver
PowerSaver The power-saving function of this product reduces power consumption by switching off the screen and changing the color of the power LED if the product is not used for a specified period of time. The power is not turned off in power-saving mode. To switch the screen back on, press any key on the keyboard or move the mouse. Power- saving mode only functions when the product is connected to a PC with a power-saving function. -
Page 81: Standard Signal Mode Table
Standard Signal Mode Table Model Name S29E790C - This product can be set to only one resolution for each screen size to obtain Synchronization Horizontal Frequency 30 – 81 kHz the optimum picture quality due to the nature of the panel. Using a resolution Vertical Frequency 56 –... - Page 82 Resolution Horizontal Frequency Vertical Frequency (Hz) Pixel Clock (MHz) Sync Polarity (H/V) (kHz) VESA, 800 x 600 46.875 75.000 49.500 - Horizontal Frequency The time required to scan a single line VESA, 1024 x 768 48.363 60.004 65.000 from the left to the right side of the screen is called a horizontal cycle.
-
Page 83: Appendix
Chapter 12 Appendix Contact SAMSUNG WORLD WIDE ― If you have any questions or comments relating to Samsung products, please contact the SAMSUNG customer care center. NORTH AMERICA U.S.A 1-800-SAMSUNG (726-7864) http://www.samsung.com/us/support CANADA 1-800-SAMSUNG (726-7864) http://www.samsung.com/ca/support (English) http://www.samsung.com/ca_fr/support (French) LATIN AMERICA... - Page 84 LATIN AMERICA COSTA RICA 0-800-507-7267 http://www.samsung.com/latin/support (Spanish) 00-800-1-SAMSUNG (726-7864) http://www.samsung.com/latin_en/support (English) DOMINICA 1-800-751-2676 http://www.samsung.com/latin/support (Spanish) http://www.samsung.com/latin_en/support (English) ECUADOR 1-800-10-72670 http://www.samsung.com/latin/support (Spanish) 1-800-SAMSUNG (72-6786) http://www.samsung.com/latin_en/support (English) EL SALVADOR 800-6225 http://www.samsung.com/latin/support (Spanish) http://www.samsung.com/latin_en/support (English) GUATEMALA 1-800-299-0013 http://www.samsung.com/latin/support (Spanish) 1-800-299-0033 http://www.samsung.com/latin_en/support (English) HONDURAS 800-27919267 http://www.samsung.com/latin/support (Spanish)
- Page 85 LATIN AMERICA PANAMA 800-7267 http://www.samsung.com/latin/support (Spanish) 800-0101 http://www.samsung.com/latin_en/support (English) PARAGUAY 009-800-542-0001 http://www.samsung.com/latin/support (Spanish) http://www.samsung.com/latin_en/support (English) PERU 0-800-777-08 http://www.samsung.com/pe/support PUERTO RICO 1-800-682-3180 http://www.samsung.com/latin/support (Spanish) http://www.samsung.com/latin_en/support (English) TRINIDAD & TOBAGO 1-800-SAMSUNG (726-7864) http://www.samsung.com/latin/support (Spanish) http://www.samsung.com/latin_en/support (English) URUGUAY 000-405-437-33 http://www.samsung.com/latin/support (Spanish) http://www.samsung.com/latin_en/support (English)
-
Page 86: Responsibility For The Pay Service (Cost To Customers)
― When the service is requested, in spite of in warranty, we may charge you for a visit from a service • Use of supplies or separatly sold product unspecified by Samsung. technician in the following cases. • Repair from a person besides an engineer of outsourcing service company or partner of Samsung Electronics Co., Ltd. Not a product defect •... -
Page 87: Terminology
Terminology OSD (On Screen Display)____ On Grey scale____ Scale refers to levels Dot Pitch____ The product and screen Vertical Frequency____ One image is Plug & Play____ The Plug & Play screen display (OSD) allows you to of color intensity that show variations consist of red, green and blue dots.
Need help?
Do you have a question about the S29E790C and is the answer not in the manual?
Questions and answers