Loctite Hysol 175-AIR Operation Manual

120 volt
Hide thumbs Also See for Hysol 175-AIR:

Advertisement

Loctite® Hysol® 175-AIR
120 Volt Part No. 98036, 230 Volt Part No. 98056
Loctite® Hysol® 175-AIR-HT
120 Volt Part No. 98040, 230 Volt Part No. 98058
EQUIPMENT
Operation Manual

Advertisement

Table of Contents
loading

Summary of Contents for Loctite Hysol 175-AIR

  • Page 1 EQUIPMENT Operation Manual Loctite® Hysol® 175-AIR 120 Volt Part No. 98036, 230 Volt Part No. 98056 Loctite® Hysol® 175-AIR-HT 120 Volt Part No. 98040, 230 Volt Part No. 98058...
  • Page 2: Table Of Contents

    Table of Contents 1. Please Observe the Following................3 Emphasized Sections ..................3 Safety ......................... 3 Items supplied....................3 2. Description ......................4 3. Technical Data ......................4 4. Installation ......................4 5. Operation ........................ 5 Adhesive Flow Rate Adjustment............... 6 6.
  • Page 3: Please Observe The Following

    1.2 Safety Do not touch the nozzle or molten adhesive with bare skin as they are hot - ® ® the operating temperature of the Loctite Hysol 175-AIR and 175-AIR- HT applicators is approximately 400ºF (200ºC). Protective gloves should always be worn.
  • Page 4: Description

    Supported by a range of adhesive formulations, the Loctite Hysol 175-AIR ® ® and 175-AIR-HT are suitable for most applications. Also, the Loctite Hysol 175-AIR and 175-AIR-HT systems are solvent-free and non-toxic, so there are none of the environmental problems often associated with other adhesive applicators.
  • Page 5: Operation

    Steps 1 – 5 should be followed before connection to the main supply: Insert the applicator stand into the grooves at the base of the handle. Stand applicator on a flat surface. Connect the air supply hose to a clean, dry and regulated air supply using the Quick-Disconnect fitting provided (use of a filter/regulator is recommended) Pull the piston back fully and rotate upwards.
  • Page 6: Adhesive Flow Rate Adjustment

    • Foam materials, like polystyrene, can be easily bonded to other surfaces. However the adhesive must be applied to the other surfaces, not to the foam. ® ® • Use only genuine Loctite Hysol adhesives to ensure reliable performance. ®...
  • Page 7: Troubleshooting

    PTFE coating; this minimizes the effect of any backup or meltdown, should it occur. FOR ANY REPAIRS OR ADJUSTMENTS – OTHER THAN THOSE DETAILED IN THIS MANUAL – PLEASE CONTACT 1-800-LOCTITE (562-8483).
  • Page 8: Care And Maintenance

    Piston Support Assembly, item 23 985093 Piston Support O-Ring Kit, Qty 10, item 24 985234 985079 Thermostat Assembly, 383°F (195°C), Hysol 175-Air, item 10 985068 Thermostat Assembly, 419°F (215°C), Hysol 175-Air-HT, item 43 Thermostat Assembly, 266°F (130°C), Option, item 46 985979 Thermostat Assembly, 356°F (180°C), Option, item 47...
  • Page 9: Accessories And Spare Parts (Continued)

    Accessories and Spare Parts (continued) Spare Parts Part Number Barrel Kit 985770 Qty 1 – PTFE, Barrel, item 2 Qty 2 – Barrel Support Ring, item 3 Qty 1 – Lock Ring, item 4 Barrel Support Kit 985778 Qty 1– Barrel Support, item 21 Qty 2 –...
  • Page 10: Accessories And Spare Parts (Continued)

    9 Accessories and Spare Parts (continued) Accessories Part Number Standard Nozzle 1-Hole Kit, Qty 5, 0.080” (2 mm) orifice 985225 Nozzle 2-Hole 985110 Nozzle 3-Hole 985111 Extension Nozzle 0.120” (3 mm) 985112 Needle Extension Nozzle 0.050” (1.3 mm) 985113 Spreader Extension Nozzle 0.250” (6 mm) 985114 ‘L’...
  • Page 11: Exploded Diagram

    Exploded Diagram...
  • Page 12: Parts List

    Parts List ITEM QTY. DESCRIPTION REBUILD KITS AVAILABLE PART NO. THERMOSTAT, 180°C, 356°F, OPTION 985123 THERMOSTAT, 130°C, 266°F 985979 HEATER HOUSING, 175-AIR-HT HEATER HOUSING KIT 985237 HEATER HOUSING KIT 985237 O-RING #2-030, ENCAPSULATED, 175-AIR-HT O-RING #2-030 ENCAP. KIT OF 10 985836 THERMOSTAT, 215°C, 419°F, 175-AIR-HT 985068...
  • Page 13: Warranty

    A claim of defect in materials or workmanship in any Products shall be allowed only when it is submitted to Henkel Loctite in writing within one month after discovery of the defect or after the time the defect should have reasonably been discovered and in any event, within twelve months after the delivery of the Products to the purchaser.
  • Page 14 Auburn Hills, Michigan 48326 Loctite is a registered trademark of Henkel Loctite Corporation, U.S.A © Copyright 2003. Henkel Loctite Corporation. All rights reserved. Data in this operation manual is subject to change without notice. P/N: 985067 Rev. E 08/03...

This manual is also suitable for:

Hysol 175-air-ht

Table of Contents