336/EEC as amended by 92/31/EEC and 93/68/EEC Art. 5 with regard to “Electromagnetic compatibility,” and 73/23/EEC as amended by 93/ 68/EEC Art. 13 with regard to “Safety.” User Information for all Countries Notice: Use the cables which are included with the projector or specified. ViewSonic PJ402D...
Page 4
PS/2, VGA and XGA are registered trademarks of International Business Machines Corporation. Disclaimer: ViewSonic Corporation shall not be liable for technical or editorial errors or omissions contained herein; nor for incidental or consequential damages resulting from furnishing this material, or the performance or use of this product.
AC line plug to prevent from signal interference due to voltage fluctuation. Ground Ground For Australia and For the U.S.A. and Canada Mainland China Ground Ground For Continental Europe For the U.K. ViewSonic PJ402D...
State-of-the-art motion adaptive hardware deinterlacing with 3:2 pull down 200-watt, user-replaceable lamp Compatibility with Macintosh computers ® Compatibility with NTSC, PAL, SECAM, and HDTV Multi-function remote control D-Sub 15-pin cable for analog video connectivity User-friendly, multi-language on-screen display (OSD) Advanced electronic keystone correction * means compressed. ViewSonic PJ402D...
Save the original shipping carton and packing material; they will come in handy if you ever to ship your unit. For maximum protection, repack NOTE your unit as it was originally packed at the factory. Accessories and components may vary by retailer and region. ViewSonic PJ402D...
Projector Components Front View 1. Lens cap 6. Focus ring 2. Lens cap strap 7. Control panel 3. Lens 8. Speaker 4. Ventilation holes (intake) 9. Front IR remote control sensor 5. Zoom ring 10. Ventilation holes (exhaust) ViewSonic PJ402D...
3. COMPUTER IN (D-SUB) connector Connect image input signal (analog) to this connector. 4. S-VIDEO connector Connect S-Video output from video equipment to this jack. 5. VIDEO connector Connect composite video output from video equipment to this jack. ViewSonic PJ402D...
Installation Connecting the Projector A. Connecting to a computer AC Power Cord VGA Cable (D-SUB to D-SUB) Desktop type Laptop type ViewSonic PJ402D...
Page 14
B. Connecting to a Video Source 1.Connecting with S-Video Cable AC Power Cord S-Video Cable Audio Cable ViewSonic PJ402D...
Page 15
2.Connecting with Composite Video Cable AC Power Cord Composite Video Cable Audio Cable ViewSonic PJ402D...
Page 16
3.Connecting with HDTV Cable AC Power Cord D-SUB to HDTV Cable Audio Cable When connecting cable, power cords of both a projector and external equipment should be disconnected from AC outlet. ViewSonic PJ402D...
Power button on the Remote Control again to turn off the power. Wait until the lamp LED indicator turns off. Please wait until the fan motor and the lamp LED turn off before removing the AC power cord from the projector. ViewSonic PJ402D...
2. Lower the projector, and then release the buttons to lock the foot adjusters into position. You may turn the foot adjuster to make fine adjustment of the height. To avoid damaging the projector, make sure that the foot adjuster is fully retracted before placing the projector in its carrying case. ViewSonic PJ402D...
2. Focus the image by rotating the focus ring. A still image is recommended for focusing. Adjusting Projection Image Size Refer to the graphic and table below to determine the screen size and projection distance. Distance between the screen and the center of the lens ViewSonic PJ402D...
Page 20
NOTE Make sure the heat ventilation holes are not blocked. Do not use the projector in a smoky environment. Smoke residue may cause buildup on critical parts (i.e. DMD, lens assembly, etc.) ViewSonic PJ402D...
Automatically adjusts frequency and phase. 5. Four direction buttons The four direction buttons / / / can be used to scroll through OSD (On- Screen Display) menus and make adjustments. 6. SOURCE ( ) Manually selects an input source. ViewSonic PJ402D...
Manually selects an input source. 8. Mute Cuts off the sound temporarily. 9. Blank Cuts off the screen temporarily. 10. 4:3/16:9 Press the 4:3/16:9 to switch the image aspect ratio from 4:3 to 16:9. 11. Auto Automatically adjusts frequency and phase. ViewSonic PJ402D...
Page 23
Do not dispose of the used battery along with household waste. Dispose of used batteries according to local regulations. Avoid excessive heat and humidity. Danger of explosion may happen if a battery is incorrectly replaced. Replace only with the same type recommended by the manufacturer. ViewSonic PJ402D...
Do not drop the remote control or jolt it. Keep the remote control out of locations with excessively high temperature or humidity. Do not get water on the remote control or place wet objects on it. Do not disassemble the remote control. ViewSonic PJ402D...
On the Projector Control Panel: Go back to main menu tab with the / buttons, and press the MENU\ENTER button. On the Remote Control: press the Menu button. The illustrations in this manual are for the purpose of explanation and may differ from the actual setting of your projector. ViewSonic PJ402D...
(through VGA cable) of resolution less than SVGA (800 x 600). If the input signal is a computer signal greater than SVGA or component 1080i / 720p, only 16:9 or 4:3 aspect ratio will be available. ViewSonic PJ402D...
Page 27
Setting 0 will maximize color reproduction quality. Color Temperature Adjusts the color temperature. With the higher temperature, the screen looks colder; with the lower temperature, the screen looks warmer. Red, Green and Blue mode activate only if the Color Temperature is set to “User”. ViewSonic PJ402D...
Page 28
Press the button to increase the color temperature. Blue Manually adjusts blue. Select the desired setting with the buttons: Press the button to decrease the color temperature. Press the button to increase the color temperature. ViewSonic PJ402D...
Sharpness Adjusts the sharpness of the image. Select the desired setting with the buttons: Press the button to decrease the sharpness. Press the button to increase the sharpness. ViewSonic PJ402D...
Press the button to move the image right. V.Position Adjusts the vertical position. Select the desired setting with the buttons: Press the button to move the image up. Press the button to move the image down. ViewSonic PJ402D...
Selects the language for menu and message displayed. Select the language you prefer with the buttons, and confirm the selection with the MENU\ENTER button on the Projector Control Panel or the Enter button on the Remote Control. English Deutsch Français Español Português Italiano ViewSonic PJ402D...
Displays operating hours since lamp timer reset. Lamp hour counter is displayed in read-only format, and this setting cannot be manually adjusted. Color Space Manually selects signal type. Select the input signal type with the buttons: YCbCr YPbPr ViewSonic PJ402D...
Volume Adjusts the volume. Select the desired setting with the buttons: Press the button to decrease the volume. Press the button to increase the volume. Mute Cuts off the sound temporarily. Select the desired setting with the buttons: ViewSonic PJ402D...
Make sure the lens is cool before cleaning. Do not use detergents or chemicals other than those noted above. Do NOTE not use benzene or thinners. Do not use chemical sprays. Use a soft cloth or lens paper only. ViewSonic PJ402D...
Leave the area immediately if the lamp shatters while being operated and ventilate the area for at least 30 minutes in order to avoid the inhalation of mercury fumes. Otherwise it could be harmful to user's health. ViewSonic PJ402D...
Page 36
Do not reuse the old lamp. This could cause the lamp to explode. Be sure to turn off the projector and unplug the AC power cord before replacing the lamp. Do not use the projector with the lamp cover removed. ViewSonic PJ402D...
AC 100 - 240 V, 50 - 60 Hz Power Consumption 250 Watts Dimension (W x D x H) 254 x 202 x 98 mm Weight 2.1 kg (4.6 lb) Note: Design and Specifications are subject to change without prior notice. ViewSonic PJ402D...
Lamp LED Green Flashing the lamp LED turns off. The fan motor will turn off when the lamp has cooled. Lamp LED Amber Flashing Temperature is too high. The lamp will turn off. ViewSonic PJ402D...
Exclusion of damages: ViewSonic’s liability is limited to the cost of repair or replacement of the product. ViewSonic shall not be liable for: 1. Damage to other property caused by any defects in the product, damaged based upon inconvenience, loss of use of the product, loss of time, loss of profits, loss of business opportunity, loss of goodwill, interference with business relationships, or other commercil loss, even if advised of the possibility of such damages.