Internal Connectors - Asus Motherboard P5LD2-VM DH User Manual

1.10.2

1.10.2 Internal connectors

1.10.2 Internal connectors Internal connectors Internal connectors
1.10.2 1.10.2 Internal connectors
1 . 1 . 1 . 1 . 1 . F l o p p y d i s k d r i v e c o n n e c t o r ( 3 4 - 1 p i n F L O P P Y ) F l o p p y d i s k d r i v e c o n n e c t o r ( 3 4 - 1 p i n F L O P P Y ) F l o p p y d i s k d r i v e c o n n e c t o r ( 3 4 - 1 p i n F L O P P Y ) F l o p p y d i s k d r i v e c o n n e c t o r ( 3 4 - 1 p i n F L O P P Y ) F l o p p y d i s k d r i v e c o n n e c t o r ( 3 4 - 1 p i n F L O P P Y )
This connector is for the provided floppy disk drive (FDD) signal cable.
Insert one end of the cable to this connector, then connect the other
end to the signal connector at the back of the floppy disk drive.
Pin 5 on the connector is removed to prevent incorrect cable connection
when using an FDD cable with a covered Pin 5.
P5LD2-VM DH Floppy disk drive connector
2 . 2 . 2 . 2 . 2 . P r i m a r y I D E c o n n e c t o r ( 4 0 - 1 p i n P R I _ I D E ) P r i m a r y I D E c o n n e c t o r ( 4 0 - 1 p i n P R I _ I D E ) P r i m a r y I D E c o n n e c t o r ( 4 0 - 1 p i n P R I _ I D E ) P r i m a r y I D E c o n n e c t o r ( 4 0 - 1 p i n P R I _ I D E ) P r i m a r y I D E c o n n e c t o r ( 4 0 - 1 p i n P R I _ I D E )
These connectors are for Ultra DMA 133/100/66 signal cables. There are
three interfaces on each Ultra DMA 133/100/66 signal cable: blue, black,
and gray. Connect the blue interface into the motherboard's IDE connector,
then select one of the following modes to configure your hard disk drive(s).
C a b l e S e l e c t M o d e C a b l e S e l e c t M o d e C a b l e S e l e c t M o d e - use this mode to select the operating mode by C a b l e S e l e c t M o d e C a b l e S e l e c t M o d e
cable connectors.
No. of drives
1
2
J u m p e r S e l e c t M o d e J u m p e r S e l e c t M o d e - use this mode to select the operating mode by J u m p e r S e l e c t M o d e
J u m p e r S e l e c t M o d e J u m p e r S e l e c t M o d e
hard disk drive jumper.
No, of drives
1
2
1 - 2 6 1 - 2 6 1 - 2 6 1 - 2 6 1 - 2 6
FLOPPY
NOTE: Orient the red markings on
the floppy ribbon cable to PIN 1.
PIN 1
Drive type Drive jumper Cable connector
With OS
With OS Cable select black
Without OS
Drive type Drive jumper Cable connector
With OS Master
With OS Master
Without OS Slave
C h a p t e r 1 : P r o d u c t i n t r o d u c t i o n C h a p t e r 1 : P r o d u c t i n t r o d u c t i o n C h a p t e r 1 : P r o d u c t i n t r o d u c t i o n C h a p t e r 1 : P r o d u c t i n t r o d u c t i o n C h a p t e r 1 : P r o d u c t i n t r o d u c t i o n
black
gray
black or gray
e