Advertisement

Quick Links

Trademarks
Copyright © PLANET Technology Corp.
Contents subject to revision without prior notice.
PLANET is a registered trademark of PLANET Technology Corp. All other
trademarks belong to their respective owners.
FCC Warning
This equipment has been tested and found to comply with the limits for
a Class B digital device pursuant to Part 15 of the FCC Rules. These
limits are designed to provide reasonable protection against harmful
interference when the equipment is operated in a commercial
environment.
This equipment generates, uses, and can radiate radio frequency energy,
and if not installed and used in accordance with the instruction manual
may cause harmful interference to radio communications. Its operation
in a residential area is likely to cause harmful interference in which case
the user will be required to correct the interference as his own expense.
Changes or modifications not expressly approved by the parties
responsible for compliance could void the user's authority to operate the
equipment.
CE Marking Warning
This is a Class A product. In a domestic environment this product may cause
radio interference in which case the user may be required to take adequate
measures.
Revision:
User's Manual for PLANET PC Card family,
Model: ENW-3502-T
Ethernet PC Card with TP jack only
Part No.: EM3502T
Rev: 1.0 (May, 1998)
About This Manual
This is a user's guide for your ENW-3502-T PCMCIA 10Mbps Ethernet
Card. Please read this manual before you attempt to install the product.
This manual includes the following topics:
Ø
Product descriptions, features and specifications.
Ø
Hardware installation procedures
Ø
Software installation procedures
i

Advertisement

Table of Contents
loading
Need help?

Need help?

Do you have a question about the ENW-3502-T and is the answer not in the manual?

Questions and answers

Subscribe to Our Youtube Channel

Summary of Contents for Planet ENW-3502-T

  • Page 1 Part No.: EM3502T Rev: 1.0 (May, 1998) About This Manual This is a user's guide for your ENW-3502-T PCMCIA 10Mbps Ethernet Card. Please read this manual before you attempt to install the product. This manual includes the following topics: Ø...
  • Page 2: Table Of Contents

    2.1 P ..................3 ACKAGE ONTENTS 2.2 H ................3 ARDWARE ESCRIPTION 2.3 I ENW-3502-T E PC C ........3 NSTALLING THE THERNET DRIVER INSTALLATION FOR WINDOWS 95..........5 DRIVER INSTALLATION FOR WINDOWS 98..........7 DRIVER INSTALLATION FOR WINDOWS NT 4.0........10 CLIENT DRIVER INSTALLATION.............. 14 6.1 D...
  • Page 3 CARDGO.EXE ..................... 27 SPECIFICATIONS ..................29...
  • Page 4 This page left blank intentionally!
  • Page 5: Introduction

    1.1 Product Description Thank you for purchasing PLANET ENW-3502-T Ethernet PC Card. ENW-3502-T 10Mbps Ethernet Card is a network adapter card for notebook computers and complies with the PCMCIA TYPE II standard. An Ethernet adapter cable with male RJ-45 connector two kinds of connections : •...
  • Page 6: Features

    10Mbps Ethernet Card and its driver software, and how to connect the card to the network. To install ENW-3502-T 10Mbps Ethernet PC Card to your notebook computer: 1. Connect the Ethernet adapter cable to the card, then insert the card into the PCMCIA slot.
  • Page 7: Hardware Installation

    It has a 68-pin connector and a 15-pin flat connector for attaching to the Notebook and Ethernet adapter cable respectively . 2.3 Installing the ENW-3502-T 10Mbps Ethernet PC Card Follow the procedure below to install the PCMCIA 10Mbps Ethernet Card.
  • Page 8 PLANET ENW-3502-T Ethernet PC Card User’s Manual 5. Turn on the computer. Use the Network coupler bundled in the package. Use of Note: other coupler could make the PC card or coupler malfunction.
  • Page 9: Driver Installation For Windows 95

    Chapter 3 Driver Installation for Windows 95 Installing the PCMCIA 10Mbps Ethernet Card is just the same as any normal Windows 95 Plug & Play device. Follow the steps below to install. 1. Insert the PCMCIA 10Mbps Ethernet Card into an open PCMCIA slot on your notebook.
  • Page 10: Enw-3502-T E

    PLANET ENW-3502-T Ethernet PC Card User’s Manual Figure 3.2 Found Driver 4. Windows 95 will follow the direction of the installation file to locate the files that should be copied. Eventually Windows 95 may need to copy required system files. Give the correct path, then click to continue.
  • Page 11: Driver Installation For Windows 98

    Chapter 4 Driver Installation for Windows 98 Installing the PCMCIA 10Mbps Ethernet Card is similar as any normal Windows 95 Plug & Play device. Follow the steps below to install. 1. Insert the PCMCIA 10Mbps Ethernet Card into an open PCMCIA slot on your notebook.
  • Page 12: Enw-3502-T E

    PLANET ENW-3502-T Ethernet PC Card User’s Manual Figure 4.2 Search Driver 4. Uncheck the Microsoft Windows Update. Let Windows 98 search floppy drive. Then place the foopy disk and click Next to continue. Figure 4.3 Search floppy Disk drive 5. Select the found updated driver, PCMCIA 10Mbps Ethernet Card, then...
  • Page 13 Chapter 4 Driver Installation for Windows 98 Figure 4.4 The updated driver 6. After copying all required files, Windows 98 will prompt you to restart the system. Click to complete installation.
  • Page 14: Driver Installation For Windows Nt 4.0

    Chapter 5 Driver Installation for Windows NT 4.0 The installation procedure assumes the network component has been installed on your computer. To check whether the network component has been installed, double click the Network icon in Control Panel. If it has not, refer to the Windows NT 4.0 installation guide to install the component.
  • Page 15 Chapter 5 Driver Installation for Windows NT 4.0 Figure 5.2 Select Network Adapter Window 4. Click Have Disk …, after Insert Disk window, shown in Figure 5.3, popped up, give the search path, A:\WINNT (suppose A: is your floppy drive), then insert driver diskette, and click OK. Figure 5.3 Insert Compact Disk Window 7.
  • Page 16: Enw-3502-T E

    PLANET ENW-3502-T Ethernet PC Card User’s Manual Figure 5.4 Select OEM Option Window 8. In the PCMCIA 10Mbps Ethernet Card setup window, Figure 5.5, select the desired IRQ level and I/O Port address. After selecting desired configuration, click OK to continue.
  • Page 17 Chapter 5 Driver Installation for Windows NT 4.0 Select the PCMCIA type option as figure 5.6 and click OK to continue. Figure 5.6 Setup Window-2 Click Close to close the Network window, and let Windows NT 4.0 binding the adapter with network component. Eventually, Windows NT 4.0 will prompt you to restart the computer, click Yes to finish installation.
  • Page 18: Client Driver Installation

    Chapter 6 Client Driver Installation 6.1 Driver Installation Before your computer system can recognize your ENW-3502-T Ethernet PCCard, the driver programs must first be installed to enable the card. 6.1.1 Driver Installation Program INSTALL.EXE is the ENW-3502-T Ethernet PC Card driver installation program.
  • Page 19: The Install Program

    Appendix A and B. 6.2 The INSTALL Program Before you can use your ENW-3502-T Ethernet PC Card, you need to install and modify some files in your computer system. You can make these changes manually, or you can let the INSTALL.EXE program do them for you.
  • Page 20 PLANET ENW-3502-T Ethernet PC Card User’s Manual The program will then prompt you for the directory where you want to install the driver files. You can choose the default directory name or enter a new name. Then, press < > to continue with installation.
  • Page 21 Chapter 6 Client Driver Installation The next screen asks if you want to do an Auto Configuration or a Custom Configuration. Select if you want to do a quick Auto Configuration installation and use the default configuration settings. If you wish to individually set any of the settings, then select Custom Configuration PCMCIA 10Mbps Ethernet Card Installation Program...
  • Page 22: Auto Configuration

    6.2.1.1 Auto Configuration If you selected Auto Configuration, the program will auto detect which IRQ ,I/O Port and Memory address the ENW-3502-T Ethernet PC Card can use. After auto-detecting the configuration successfully, the program will show the following screen :...
  • Page 23 < >. Enter PLANET ENW-3502-T Ethernet PC Card Installation Program SELECT DRIVERS YOU WANT TO INSTALL Please select the network drivers that you want to install. Use the arrow key to highlight the desired item. When a item is highlighted press <Enter> to select it. If the network drivers that you want to install to is not in the following list, please press <Esc>...
  • Page 24: Custom Configuration

    PLANET ENW-3502-T Ethernet PC Card User’s Manual After selecting the Network Operating System, the INSTALL program will copy and/or modify some files on your boot drive. Your CONFIG.SYS file will also be modified to include the Client Driver. You should see the following message if installation has been successful.
  • Page 25 Chapter 6 Client Driver Installation PLANET ENW-3502-T Ethernet PC Card Installation Program SELECT INTERRUPT Please select the hardware interrupt that you would like your 10Mbps Ethernet Card to use. Use the arrow key to highlight the desired value. When a value is highlighted press <Enter>...
  • Page 26 PLANET ENW-3502-T Ethernet PC Card User’s Manual PLANET ENW-3502-T Ethernet PC Card Installation Program SELECT I/O PORT Please select the I/O Port that you would like your 10Mbps Ethernet Card to use. Use the arrow key to highlight the desired value. When a value is highlighted press <Enter>...
  • Page 27: Manual Installation

    Chapter 6 Client Driver Installation 6.3 Manual Installation In most cases, the INSTALL program can make all system changes necessary for using your PCMCIA 10Mbps Ethernet Card. But in some cases, you may wish to make the change manually. This section explains the driver and file modifications needed to enable your PCMCIA 10Mbps Ethernet Card.
  • Page 28: Client Driver Installation

    PLANET ENW-3502-T Ethernet PC Card User’s Manual Node ID : 00 A0 0C 01 00 3A (for example) The list of error messages the client driver may display and the correction methods we suggest are given in Appendix B. 6.4 Client Driver Installation 6.4.1 NetWare 3.X / 4.X Client...
  • Page 29: Microsoft Lan Manager

    Chapter 6 Client Driver Installation 6. Set the proper IRQ and IO Port settings for this card. 7. Set bus type to be PCMCIA and bus number to be 0. 8. Reboot the computer and installation is completed. 6.4.4 Microsoft LAN Manager Installation procedure: 1.
  • Page 30: Troubleshooting For Windows Environments

    Appendix A Troubleshooting for Windows Environments These guidelines give you tips to deal with some problems on using PCMCIA 10Mbps Ethernet Card. If the problems remain unsolved, contact your dealer for assistance. A.1 Windows 9X 1. Ejecting the card from the PCMCIA socket hangs or reboots the computer.
  • Page 31: Error Messages Of Enabler Program

    Appendix B Error Messages of Enabler Program CARDGO.EXE Here is the list of error messages the CARDGO.EXE may display and correction method we suggested. [Error 1] "PCMCIA 10Mbps Ethernet Card enabler failed in request IRQ." The IRQ number you specified is not supported by the Card Services or is in conflict with another device.
  • Page 32 PLANET ENW-3502-T Ethernet PC Card User’s Manual [Error 8] "Parameter too long." Too many parameters issued with CARDGO. Correction : Refer to the default syntax listed above and correct it. [Error 9] "Unknown parameters." CARDGO.EXE Syntax error. Correction : Refer to the default syntax listed above and correct it.
  • Page 33: Specifications

    Appendix C Specifications Model: ENW-3502-T IEEE802.3 10BASE-T Standards Conformance: Card Size: 5.0mm Type II 16-bit Bus Width: Communication Mode: Half-duplex UTP-3,4,5 for 10Base-T Media Supported: Operating Distance: 100m maximum hub to node distance RJ-45 connector for 10Base-T Network Interface: Socket Interface:...

Table of Contents