Overview wePresent WiPG-1500 is professional wireless presentation gateway. By enabling the Revolutionary “interactive” and “UST/UoIP” functions, you can throw your presentations wirelessly from a PC, Mac, iPad, iPhone, or Android devices to a projector, and use the touch screen/IWB, mobile phone or Pad to control the presentation remotely.
Page 6
• Basic Features ▪ High performance screen/audio projection for Windows/Mac (Windows8 and Mac Mountain Lion) ▪ Remote desktop control from USB AirStick, Touch Screen or Mouse/Keyboard for Windows/Mac ▪ Plug&Show: launching the projection application from a USB thumb drive without installation ▪...
Physical Details Front Panel Power Button and LED USB Port Description Power on/off button. Power Button and LED LED Indicator: System Loading(Red), Ready(Yellow) USB Port (Front) USB port for USB mouse and keyboard →Back Chapter 4 Physical Details...
Rear Panel USB Port Audio Jack Antenna RJ-45 VGA Connector HDMI Power Jack Antenna Description Antenna WiFi Antenna USB Port (Rear) USB port for USB IWB device (HID type) RJ-45 10/100M RJ-45 port VGA Connector VGA connector HDMI HDMI Connector Audio Jack Audio Jack (3.5mm) Power Jack...
Page 11
Bottom Side Screw hole Reset Button (Optional kit for Wall Mount) Description Screw Hole Screw Hole for Wall Mount Kit Press reset button and power on the Reset Button device to execute Hardware Reset. →Back Chapter 4 Physical Details...
AirStick AirStick USB device is wireless remote controller. It can control the WiPG-1500 device and projecting PC/Mac remotely. Up Key ESC Key Page Up Mouse Page Down Mouse Right Key Left Key Micro USB charging port Down Key Power switch...
What You Might Need Projector or HDTV with VGA/HDMI interface Windows or Mac PC/Laptop Apple iPhone, iPad or iPod-touch device Android Phone or Tablet device Speaker (Optional, for audio projection feature) USB Mouse and Keyboard (Optional, for remote desktop feature) USB HID Touch Screen/IWB Device (Optional, for UST or IWB over IP feature) →Back Chapter 6...
Quick Installation 1. Connect wePresent WiPG-1500 device to Projector through VGA/HDMI port and turn on projector power. →Back Chapter 7 Quick Installations...
Page 15
It will show the default standby screen as below when system is ready. 3. Attach the speaker cable to WiPG-1500 phone jack for audio output 4. Attach the USB mouse and keyboard to WiPG-1500 front USB port for OSD control and remote desktop control 5.
WiPG-1500 Receiver Device 8.1 PC-List 1. If there are sender connected to WiPG-1500 device, it will show the available PC- List on standby screen, conference moderator can use the USB mouse/keyboard/ Touch Screen/IWB to select the PC and control it remotely.
2. You can also click the feature Icon to browse the Quick Guide for each highlight feature. 8.2 Setup Page Click the “Setup” icon, you can find the FW version, resolution and WiFi security information. Meanwhile, you can also calibrate the attached Touch Screen/IWB screen coordination by “Calibration” function. →Back Chapter 8 WiPG-1500 Receiver Device...
8.3 Remote Touch Control (UST/UoIP) WiPG-1500 can support standard Win7/8 compatible HID touch device. By attaching the HID touch screen/IWB device, you can operate the standby screen, White Board feature and the projecting PC/mobile remotely from the Touch Screen/IWB device.
8.5 Pen drawing When user are projecting through Windows, Mac, Android and iOS sender application, you can use the AirStick/Mouse/IWB/Touch Screen to enable the Pen feature and add free drawing on top of projecting screen. →Back Chapter 8 WiPG-1500 Receiver Device...
DoWiFi for Windows 9.1 Install the application 1. Make sure your PC WiFi is enabled already, and connect your PC to wePresent WiPG-1500 box through WiFi. 2. Open your browser and enter the Device Host Name (SSID) or IP address in the browser.
WiPG-1500 software to pass through.) 9.2 Start the application 1. Click wePresent WiPG-1500 icon on desktop to execute the application, or launch the application from PnS token directly. 2. It will start to search wePresent WiPG-1500 receiver automatically.
1. WiPG-1500 will memorize the last successful connection profile and open the quick connect dialog, you can enter the code and press the “Connect” button to connect this WiPG-1500 directly. 2. If you want to connect to another WiPG-1500 receiver, please press the “Rescan” button. 9.4 Connect to WiFi Network 1.
IP address manually and connect. 9.6 Login 1. When it connects to a “Code” protection enabled WiPG-1500 receiver, you have to enter the “Code” and press the “Connect” button to login the receiver. (You can find the CODE from the right-upper of OSD standby screen) 2.
9.7 Main User Interface Menu Area Control Area for Screen Status Indicator Projection Feature 9.8 Screen Projection Click the “Play” button for full or “1,2,3,4” for split screen projection, you can project the main screen on to the display immediately. Click the “Pause” button, you can freeze you projection screen, and click the “Stop”...
9.9 Audio Projection 1. When you are doing the full screen projection or project to split #1 screen, you can also choose to project the audio to WiPG-1500 receiver for the multimedia or video scenario. 2. To enable or disable the audio projection feature, please change the setting from WiPG-1500 menu.
Item Description Show Receiver Information Show Receiver Information on screen Web Admin Open web admin page Search Receiver Connect to another receiver device Launch SidePad Launch SidePad sender Enable WebSlides Enable WebSlides Select Projection Desktop Select the projection desktop Projection Quality Change projection quality Projection Mode Change the presentation or video mode.
9.10.4 Launch SidePad 1. Open the main menu of the WiPG-1500 application(Win/Mac), and choose the item, “Launch SidePad” Note: You have to download the “SidePad receiver” on your Android/iOS device, and then connect the Android/iOS to WiPG-1500 device through WiFi and Launch “SidePad receiver”.
Click the “Enable WebSlides”, it will start to broadcast your slides to the browser on connected mobile devices. Note: Audience need to connect to WiPG-1500 WiFi Network, open the browser and click the “WebSlides” button to start receiving the slides.
9.10.10 Projection Aspect Ratio Click the “Projection Aspect Ratio”, choose “Keep aspect ratio” to keep the original aspect ratio if the desktop resolution is different from WiPG-1500 output resolution, or choose “Fit full screen” to project the screen to full screen.
9.10.11 Enable USB IWB Bridge 1. Click the “Enable USB IWB Bridge”, it will enable the USB IWB Bridge feature. 2. When you start the full screen projection, it will bridge the IWB device to your PC wirelessly. Note: You have to install the USBoIP driver first. You can find the driver from USB token. 9.10.12 Advanced Screen Capture Click the “Advanced Screen Capture”, you will be able to see tip windows and other layered windows (include the main UI) on the connected display.
“highest performance”, however, you can click the “Auto Power Manage” to enable or disable this function and restore you power scheme immediately. 9.10.15 Auto WiFi Connect Click “Auto WiFi Connect” to enable the WiPG-1500 WiFi connect feature. →Back Chapter 9 DoWiFi for Windows...
9.10.16 Make wePresent WiPG-1500 Token Click “Make wePresent WiPG-1500 Token” to make a USB wePresent WiPG-1500 Token, you can insert a USB thumb drive and follows the wizard to make the Token. →Back Chapter 9 DoWiFi for Windows...
9.10.17 Copy Application to desktop Click the “Copy Application to desktop”, it will copy the application to your desktop immediately even you don’t have the system privilege 9.10.18 Hot Key Click “Hot Key” to display the available Hot Key definition. 9.10.19 About Click “About”...
DoWiFi for Mac 10.1 Install the application 1. Make sure your PC WiFi is enabled already, and connect your PC to wePresent WiPG-1500 box through WiFi. 2. Open your browser and enter the Device Host Name (SSID) or IP address on browser.
1. WiPG-1500 will memorize the last successful connection profile and open the quick connect dialog, you can enter the code and press the “Connect” button to connect this WiPG-1500 directly. 2. If you want to connect to another WiPG-1500 receiver, please press the “Rescan” button. 10.4 Connect to WiFi Network 1.
“Skip” button. 10.5 Connect to Receiver Device 1. WiPG-1500 will search and list the WiPG-1500 receiver Device. You can select the target receiver device and press the “Connect” button to connect the selected receiver device.
10.6 Login 1. When it connects to a “Code” protection enabled WiPG-1500 receiver, you have to enter the “Code” and press the “Connect” button to login the receiver. (You can find the CODE from the right-upper of OSD standby screen) 2.
1. When you are doing the full screen projection, you can also choose to project the audio to WiPG-1500 receiver for the multimedia or video scenario. 2. To enable or disable the audio projection feature, please change the setting from WiPG-1500 menu.
10.10 Menu Press “Menu” button from the main UI, you will find the menu to enable the additional feature or to change the application options. Item Description Show Receiver Information Show Receiver Information on screen Web Admin Open web admin page Search Receiver Device Connect to another receiver device Launch SidePad...
Click “Search Receiver Device”, it will disconnect from current receiver and search the receiver again. 10.10.4 Launch SidePad 1. Open the main menu of the WiPG-1500 application(Win/Mac), and choose the item, “Launch SidePad”. Note: You have to download the “SidePad Receiver” on your Android/iOS device, then connect the Android/iOS to WiPG-1500 device through WiFi and Launch “SidePad...
Click the “Enable WebSlides”, it will start to broadcast your slides to the browser on connected mobile devices. Note: Audience need to connect to WiPG-1500 WiFi Network, open the browser and click the “WebSlides” button to start receiving the slides.
10.10.7 Projection Quality Click the “Projection Quality”, choose “Normal” for faster projection speed with lower screen image quality, and “Best” for clear screen image quality but slower projection speed. 10.10.8 Select Projection Mode Click the “Select Projection Mode”, choose the Presentation mode for shortest latency or the Video mode for auto-latency control to have better video performance.
10.10.10 Projection Aspect Ratio Click the “Projection Aspect Ratio”, choose “Keep aspect ratio” to keep the original aspect ratio if the desktop resolution is different from WiPG-1500 output resolution, or choose “Fit full screen” to project the screen to full screen.
10.10.14 About Click “About” to show system information. It includes product model name, Client version, IP address and other information. 10.10.15 Exit Click “Exit” to exit this application. It will stop current playing status and close the application immediate. →Back Chapter 10 DoWiFi for Mac...
Web Management 11.1 Home Page 1. Make sure your PC connect to wePresent WiPG-1500 box successfully. 2. Enter the receiver IP address on browser; you can find the IP address on the projector screen. (Default IP is 192.168.100.10) →Back Chapter 11...
2. Enter password and then press [Login]. (Default password: moderator) 3. After login, you can see a User List on the screen which indicates all of users con- nected to WEPRESENT WiPG-1500 box. 4. There are three columns, “Computer Name”, “Play Control” and “IP Address”.
, Play Split #4 and Stop 6. Uncheck the “Allow Control from this page only”, it will disable the centralized control and user can project the screen to WiPG-1500 freely. 11.4 WebSlides 1. Press the “WebSlides” button to enter the WebSlides page.
Wireless MAC address : wireless MAC address Wire MAC address : wire MAC address Connection Status: Projecting status : “Waiting for projecting” or “Projecting” Total Users : It shows how many users login to wePresent WiPG-1500. Code : It will show current Code →Back Chapter 11...
The default setting of the wePresent WiPG-1500 box is DHCP client. When the wePresent WiPG-1500 box is connected to a LAN that already has a DHCP server present, the wePresent WiPG-1500 box takes an IP address assigned to it by the server.
Page 51
SSID Broadcast: The default value is “Enable” Channel: to set fixed channel or Auto. The “Auto” means after power on wePresent WiPG-1500, it will scan all of wireless channel and select clear one channel automatically. Encryption: you can select “Disable” or one of WEP/WPA/WPA2 64bit or 128bit in ASCII or HEX string.
Page 52
< Gatekeeper> Gatekeeper is designed for ensuring the enterprise network security within wePresent WiPG-1500 box All Block can block Guest Users(through wireless) to access all office network(LAN), All Allow can pass Guest Users(through wireless) to access all office network Internet Only can block Guest Users (through wireless) from office network (LAN) but still reserve internet connection capability.
11.5.4 OSD Setup Click [OSD Setup] button, you can change the standby Logo image Change Standby Image Replace Logo Image: Replace logo image only. Replace entire standby image: Replace the whole standby image <Reset to default>: Restore to default Logo image. <Image File Upload>: Upload the customized Logo Image.
*** To execute the Hardware Factory Reset to Default, Please follow below procedures. 1. Press [Reset] button and Hold. 2. Turn on wePresent WiPG-1500 box. 3. Wait for over 10 seconds and relief [Reset] button. 4. It will take effect to restore factory default settings.
2. System Configuration Import and Export 3. Export: Export the system configuration to a configuration file 4. Import: Import the system configuration file to WiPG-1500 5. Firmware Upgrade a. Firstly, you have to get latest firmware image file from your vendor.
Warning: Don’t power off wePresent WiPG-1500 while firmware upgrade in progress, otherwise will cause your Box doesn’t work and have to return device to your vendor for fixing. 11.5.8 WebSlides Setup 1. Click [WebSlides Setup] button to setup the WebSlides Feature.
11.5.9 Reboot System Click [Reboot System] button, you can restart the system <Reboot>: reboot system automatically. 11.5.10 Logout Click [Reboot System] button, you can logout the WiPG-1500 →Back Chapter 11 Web Management...