Table of Contents
Advertisement
Advertisement
Table of Contents
Related Manuals for Asko DW95
Summary of Contents for Asko DW95
- Page 1 INDEX DISHWASHERS DW95...
- Page 2 Content Page Dishwashers DW950, 951 952 95C DW953, 354 955, 95FI 8-16...
- Page 3 1. PROGRAMS DW 950, 951, 952, 95C Rinse & Hold program One rinse without heat. Intensive wash program 3 pre-washes, main wash, 2 rinses and drying. Basic temperature: 65°C in first pre-wash, main wash and last rinse. 30°C in second pre-wash . 70°C in drying. Normal wash program Two pre-washes, main wash, 2 rinses and drying.
- Page 4 2. PROGRAM OPTIONS BUTTONS The dishwasher can have 1, 2 or 3, option pushbuttons and 1 rotary switch for water softner setting. Drying heat You can select drying with or without heat. Temperature Selection between 55°C and 65°C in main wash, last rinse and in pre-wash in the Intensive wash program.
- Page 5 ELECTRICAL FUNCTION CONTROL UNIT DW951, 952, 95C has an electro-mechanical timer. CIRCULATION PUMP The circulation pump consists of an asynchronous motor and pump, constructed in an integrated unit. A 4 µF capacitor is fitted to ensure reliable starting of the circulation pump. OUTLET PUMP The outlet pump consists of a synchronous motor and pump, constructed in an integrated unit.
- Page 6 DOOR SWITCH A microswitch senses that the door has been opened. This interrupts the pro gram and cuts the power to all control components (motor, valves etc.). See fault indications on page 7. LEVEL SWITCH The level switch provides protection against overfilling, interrupting the power supply to the inlet valve and starting the outlet pump.
- Page 7 ELECTRICAL SUPPLY As delivered , the machines are wired for connection to a single-phase, 230 V, 10 A supply, with a heater MAIN SWITCH The main switch is a 2-pole switch, interrupting both the phase and neutral supplies. power of 1800 W, giving a total power requirement of 2000 W. Alternative:single-phase, 230 V, 16 A, heater power 3000 W total power requirement 3200 W .
- Page 8 WATER SOFTENING The water softener operates as follows: During rinse, pre-wash and main wash: 1. Inlet valve 1 opens and admits water. 2. The water flows • through hose 3 to air-brek device, no 1 • passes an airgap • leaves the air-break device through no. 3 •...
- Page 9 THE SALT CONTAINER 0,05 - 0,23 litres of water flow into the salt Na Cl Na Cl container, where the Ca is CaCl replaced by Na. 2NaCl CaCl is flushed into the machine. Rinses Rinse 1 starts by flushing the water softener system for 40-90 seconds, depending on setting, at the same time as the machine pumps out.
- Page 10 Start Stop DW 955 DW 954 DW 953 DW 95.FI PROGRAMS DW 953, 954, 955, 95FI Pots & Pans program Two pre-washes, main wash, 4 rinses and drying. Basic temperature: 45°C in first pre-wash 70°C in main wash, 65°C in last rinse. Strong wash program Two pre-washes, main wash, 3 rinses and drying.
- Page 11 Quick wash program One pre-wash, short main wash and 2 rinses. Basic temperature: 55°C in main wash and last rinse. Rinse & Hold program One pre-wash without heat. Plate heating Consists of a dry sequence. OPTIONS Delayed start DW 955: You can select 1-12h´s delay. DW 954/95.FI: Just 5h´s delay.
- Page 12 EXTRA RINSE (Not DW 953)== An extra rinse can be added in programs Intensive, Strong, Normal and Lightwash. Press S2 five times Press S5 to get an extra rise or press S4 to get a normal number of rinses. SETTING OF PUMPING-OUT TIME The pumping-out time can be changed depending on bad pumping-out conditions.
- Page 13 FAULT-TRACING PROGRAM The fuctions of the elctrical components can be tested: Press S6 five times. Press S2 for inlet valve 2. Press S3 for inlet valve 1. Press S4 for combi doser. Press S5 for the heating element Press S6 for the circulation pump. Press S7 for the outlet pump.
- Page 14 FAULT INDICATIONS L3 and L7 and display ”F1” (DW955) is blinking: Heating element fault. L1-L8 and display ”F2” (DW955) is blinking: Overfill. L4 and L5 and display ”F3” (DW955) is blinking: Sensor fault. L6 and L7 and display ”F4” (DW955) is blinking: Water inlet fault.(Just machines with level sensor).
- Page 15 DOOR SWITCH A microswitch senses that the door has been opened. This interrupts the program and cuts the power to all control components (motor, valves etc.). LEVEL SWITCH The level switch provides protection against overfilling, interrupting the power to the inlet valve and starting the outlet pump. If the water level has not dropped within 30 seconds or if overfill has occurred twice during the same program, the program will be terminated The overfill protection operates during all programs, including fault-tracing, and...
- Page 16 Evacuates the moist air from the machine during the drying phase of the program. The fan system consists of a fan motor which runs a two part impeller. Dry air is sucked in from the door into one of the impeller halves. A vax motor opens a valve, and the moist air streams into the other part of the impeller.
- Page 17 WATER SOFTENING The water softener operates as follows: During rinse, pre-wash and main wash: 1. Inlet valve 1 opens and admits water. 2. The water flows • through hose 3 to air-brek device, no 1 • passes an airgap • leaves the air-break device through no. 3 •...
- Page 18 THE SALT CONTAINER 0,05 - 0,23 litres of water flow into the Na Cl Na Cl salt container, where the Ca is CaCl replaced by 2NaCl Na. CaCl flushed into the machine. Rinses Rinse 1 starts by flushing the water softener system for 40-90 seconds, depending on setting, at the same time as the machine pumps out.