Related Manuals for XTS PTZ1800VIR-WP
Summary of Contents for XTS PTZ1800VIR-WP
-
Page 1: User Manual
USER MANUAL PTZ1800VIR-WP/PTZ2800VIR-WP/PTZ3600VIR-WP Portable All-Condition Rugged PTZ Camera (IR and White Light Versions) - Page 3 Safety Notes Thank You for Choosing Our Portable All-Condition Rugged PTZ Camera! When you open the box: 1. Check that the packing and the contents are not visibly damaged. Contact the retailer immediately if any parts are either missing or damaged. 2.
-
Page 4: Table Of Contents
Table of Contents Safety Notes --- Important!!! ................1 About The Product ..................2 Features ......................2 Functions ......................3 Technical Data ....................6 Preparation ...................... 8 Dip Switch ...................... 8 Initial Power On Test ..................9 Installation Place ..................10 Installation ..................... -
Page 5: Safety Notes
Safety Notes --- Important!!! The following important notes must be followed carefully to run the camera and respective accessories in total safety. The camera and relative accessories are called video system in this section. Before installing the camera, please read this manual carefully; when installing please follow instructions of installation indicated in this manual. -
Page 6: About The Product
About The Product PAC series camera is designed for fixed and mobile video surveillance applications, such as marine, law enforcement, army, border patrol, airport, oilfield etc. It consists of: high resolution zoom module, powerful IR or white lighting module, precise PTZ system, optional damping systems. -
Page 7: Functions
About The Product New design of drive system, PTZ positioning precision up to +/-0.050; Camera address easily changeable via software; Baud rate, protocol self-adaptive; Digital image stabilization; Image flip for stand / ceiling mount; Video freeze; ... -
Page 8: Zoom Control
About The Product Pan/Tilt and camera to that position. User can save and call presets easily and promptly by using keyboard controller or infrared controller. The camera supports up to 256 presets. Zoom control User can adjust zoom wide or tele by controller and get desired image. Focus control System defaults Auto Focus mode, that is, the lens and camera will automatically adjust the focus to get the best image. - Page 9 About The Product Auto White Balance Camera can automatically adjust white balance (WB) according to the alteration of background lightness to give a true color image. Back Light Compensation (BLC) If a bright backlight presents, the subjects in the picture may appear dark or as a silhouette. Backlight compensation enhances objects in the center of the picture.
-
Page 10: Technical Data
About The Product Technical Data Camera Image Sensor 1/4” SONY EX-View HAD CCD Effective Pixel PAL: 752(H)×582(V); NTSC:768(H)×494(V) Resolution 550 TVL Video System PAL/NTSC Optical Zoom Digital Zoom 0.01Lux 0.0015Lux Min Illumination (Lights Off) (Lights Off) 0Lux (Lights On) 0Lux (Lights On) White Balance Auto Focus... - Page 11 About The Product Light (for White Light Version) Color Temperature 6500K Lamp Power (including driver) Brightness 2100LM Range 120m Switch Manual General Comm. Interface RS-485 Protocol PELCO-P / PELCO-D Baud Rate 2400bps, 4800bps, 9600bps, 19200bps (self-adaptive) Address 0-255 Voltage DC 10.8-28V 20W (Defogger and lights off) Power 40W (Defogger on and lights off)
-
Page 12: Preparation
Preparation This section contains detailed instructions for installing the camera. These instructions assume that the installer has a good knowledge of installation techniques and is capable of adopting safe installation methods. Dip Switch The factory default is: Camera Address Protocol Baud Rate Pelco D 9600bps... -
Page 13: Initial Power On Test
Preparation Initial Power On Test To ensure the camera works well after installation, please power on it for an initial test with the following steps: 1. Connect the camera with correct power supply; 2. Connect control cable, video cable; 3. Power on the camera; When the camera is powered on, the LED indicators at the front will be on. -
Page 14: Installation Place
Preparation DOME ID：001 PROTOCOL：PELCO-D/P BAUD：9600 SOFTWARE VER： 1.4.4 CAM FAIL Please refer to the following code to check the failures: PAN FAIL Failure of pan initialization TILT FAIL Failure of tilt initialization CAM FAIL Failure of block camera initialization P/T FAIL Failure of pan and tilt initializations T/Z FAIL Failure of tilt and block camera initializations... -
Page 15: Installation
Installation Fixed Mounts The fixed mount provides damping system as optional. Fig. 4: Fixed Mounts (with and w/o damping system) -
Page 16: Installation
Installation Installation To set the baud rate, protocol and camera hard address: 1. Remove the PTZ bottom plate; 2. Set DIP Switch for baud rate, protocol and camera address; 3. Fix the bottom plate. Make sure the sealing is well installed. Fig. -
Page 17: Camera Cable Package
Installation Fig. 7: Mount the Installation Plate 6. Fix the camera to the installation plate with a screw. Fig. 8: Fix the Installation Plate Camera Cable Package Connect the cable with the right pins as per following pictures. Fig. 9: Cable Package... - Page 18 Installation 6Pin Cable: Pin Definition Video + Power - Power + RS485 - RS485 + Video - There are two red marks each on the plug and socket. Please match them during plugging. [Note] Please make sure the camera is working with a right power supply. Wrong cable connection may cause damage to the device.
-
Page 19: Operation
Operation Special Control Panel Commands The camera can be programmed and operated using various quick control panel commands. Default Preset Number Function Value General preset positions ≤20 ~ ≥80 Manual switch between color mode (with light off) and mono GO TO 21 mode (with light on). -
Page 20: Operation
Operation GO TO 59 PTZ Speed - Fast GO TO 60 PTZ Speed - Normal √ GO TO 61 PTZ Speed - Slow GO TO 62 Decrease The Camera Address By -1 GO TO 63 Increase The Camera Address By +1 GO TO 70 Turn on low lights only (only for white light models) GO TO 71... - Page 21 Operation [Note] When the ambient temperature is above +50℃, the aux lighting system is suggested to be turned off to protect the PTZ cameras. Image Freeze Call Preset 28 to turn on/off the function. When it is on, during a regular preset call (see following picture), the video will be frozen at point A till Point B.
- Page 22 Operation the camera is rebooted. Digital Image Stabilization (DIS) The function is off as default. It can be turned on/off by calling preset 29. It is used when the camera is used in a vibration environment, to compensate the vibration in video.
-
Page 23: Trouble Shooting
Trouble Shooting Problems Possible Causes Solutions Power supply failure Replace power supply No action when powered Wrong connection Check & reconnect the cables power Mechanical failure Repair Abnormal self-test with Camera inclined Reinstall the camera motor noise Inadequate power supply Replace the power supply Video signal failure Reinstall camera... -
Page 24: Annex: Dip Switch - Camera Address
Annex: DIP Switch – Camera Address ADDRESS... - Page 25 ANNEX: DIP SWITCH – CAMERA ADDRESS...
- Page 26 ANNEX: DIP SWITCH – CAMERA ADDRESS...
- Page 27 ANNEX: DIP SWITCH – CAMERA ADDRESS...
- Page 28 ANNEX: DIP SWITCH – CAMERA ADDRESS...
- Page 29 ANNEX: DIP SWITCH – CAMERA ADDRESS...
- Page 30 ANNEX: DIP SWITCH – CAMERA ADDRESS Table 4: DIP Switch – Camera Address...
- Page 31 Modification History Revision Date of Release Modified Contents Ver 1.0 Jan 1 2012 Official release of first version...
- Page 32 Office Headquarters: 8880 NW 18th Terrace Doral, FL 33172 USA T: 1.855.797.8XTS T: 1.305.863.7779 www.xtscorp.com...